Loose A70 MKP Series Taped METALLIZED POLYPROPYLENE CAPACITOR MULTIPURPOSE APPLICATIONS Typical applications: temperature compensation circuits, timing, oscillator circuits, power factor correction and coupling capacitor in SMPS applications. PRODUCT CODE: A70 D max 5 >5 7 Od 0.05 0.5 0.6 All dimensions are in mm. >7<16 0.8 16 1 Product code system GENERAL TECHNICAL DAta Dielectric: polypropylene film. The part number, comprising 14 digits, is formed as follows: Plates: aluminium layer deposited by evaporation under 1 2 3 4 5 6 7 8 9 10 11 12 13 14 vacuum. Winding: non-inductive type. A 7 0 Leads: tinned wire. Protection: polyester tape wrapping and thermosetting resin Digit 1 to 3Series code. end fill. Digit 4 d.c. rated voltage: Marking: Manufacturer's logo, series (1.70), dielectric G =160V I = 250V M = 400V P = 630V code (MKP), capacitance, tolerance, D.C. rated Digit 5 Length (mm): voltage. F=11; H=14; K=20.5; Q=28; T=33 Climatic category: 55/105/56 IEC 60068-1 Digit 6 to 9 Digits 7 - 8 - 9 indicate the first three digits of Operating temperature range: -55 to +105C Capacitance value and the 6th digit indicates Related documents: IEC 60384-16 the number of zeros that must be added to obtain the Rated Capacitance in pF. Digit 10 to 11 Mechanical version and/or packaging (table1) Digit 12 Identifies the dimensions and electrical characteristics. Winding scheme Internal use Digit 13 Digit 14 Capacitance tolerance: J=5%; K=10%; M=20%. single sided metallized polypropylene film Table 1 (for more detailed information, please refer to page 14). Standard packaging style Ordering code Reel O 355 mm 26 Loose AA 09/2008 (Digit 10 to 11) 64 A70 MKP Series METALLIZED POLYPROPYLENE CAPACITOR MULTIPURPOSE APPLICATIONS PRODUCT CODE: A70 Rated Cap. 160Vdc/90Vac D max L max Max dv/dt (V/s) Max K0 0.022 F 5.0 11.0 5 1.60 E3 5.0 11.0 5 1.60 E3 0.047 F 5.0 11.0 5 1.60 E3 0.068 F 5.5 14.0 5 1.60 E3 0.10 F 5.5 14.0 5 1.60 E3 0.15 F 6.5 14.0 5 1.60 E3 0.22 F 7.5 14.0 5 1.60 E3 0.33 F 7.0 20.5 3 0.96 E3 0.47 F 8.0 20.5 3 0.96 E3 0.68 F 8.0 28.0 2 0.64 E3 1.0 F 9.5 28.0 2 0.64 E3 1.5 F 11.0 28.0 2 0.64 E3 2.2 F 12.0 33.0 1 0.32 E3 3.3 F 14.5 33.0 1 0.32 E3 4.7 F 17.0 33.0 1 0.32 E3 Max dv/dt (V/s) Max K0 250Vdc/200Vac L max 5.0 11.0 11.0 5.5 E3 0.015 F 5.0 11.0 11.0 5.5 E3 0.022 F 5.5 14.0 10.0 5.0 E3 0.033 F 5.5 14.0 10.0 5.0 E3 0.047 F 6.0 14.0 10.0 5.0 E3 0.068 F 7.0 14.0 10.0 5.0 E3 0.10 F 8.5 14.0 10.0 5.0 E3 0.15 F 7.5 20.5 7.0 3.5 E3 0.22 F 9.0 20.5 7.0 3.5 E3 0.33 F 8.5 28.0 4.0 2.0 E3 0.47 F 10.0 28.0 4.0 2.0 E3 0.68 F 11.5 28.0 4.0 2.0 E3 1.0 F 12.5 33.0 2.5 1.3 E3 1.5 F 15.0 33.0 2.5 1.3 E3 2.2 F 18.0 33.0 2.5 1.3 E3 3.3 F 21.5 33.0 2.5 1.3 E3 Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) All dimensions are in mm. A70GF 2220--0-- L max Max dv/dt (V/s) Max K0 (V2/s) 6800 pF 5.0 11.0 25.0 20.0 E3 A70GF 2330--0-- 0.010 F 5.5 14.0 13.5 11.0 E3 A70GF 2470--0-- 0.015 F 6.0 14.0 13.5 11.0 E3 A70GH 2680--0-- 0.022 F 6.0 14.0 13.5 11.0 E3 A70GH 3100--0-- 0.033 F 6.5 14.0 13.5 11.0 E3 A70GH 3150--0-- 0.047 F 8.0 14.0 13.5 11.0 E3 A70GH 3220--0-- 0.068 F 7.0 20.5 10.0 8.0 E3 A70GK 3330--0-- 0.10 F 8.0 20.5 10.0 8.0 E3 A70GK 3470--0-- 0.15 F 8.0 28.0 6.5 5.2 E3 A70GQ3680--0-- 0.22 F 9.5 28.0 6.5 5.2 E3 A70GQ4100--0-- 0.33 F 11.0 28.0 6.5 5.2 E3 A70GQ4150--0-- 0.47 F 13.0 28.0 6.5 5.2 E3 A70GT 4220--0-- 0.68 F 13.5 33.0 4.0 3.2 E3 A70GT 4330--0-- 1.0 F 16.5 33.0 4.0 3.2 E3 A70GT 4470--0-- 1.5 F 20.0 33.0 4.0 3.2 E3 Rated Cap. D max L max Max dv/dt (V/s) 1000 pF 5.0 11.0 30 38.0 E3 A70IF 2150--0-- 1500 pF 5.0 11.0 30 38.0 E3 A70IH 2220--0-- 2200 pF 5.0 11.0 30 38.0 E3 A70IH 2330--0-- 3300 pF 5.0 11.0 30 38.0 E3 A70IH 2470--0-- 4700 pF 5.0 11.0 30 38.0 E3 A70IH 2680--0-- 6800 pF 5.5 14.0 20 25.0 E3 A70IH 3100--0-- 0.010 F 6.0 14.0 20 25.0 E3 A70IK 3150--0-- 0.015 F 7.0 14.0 20 25.0 E3 A70IK 3220--0-- 0.022 F 8.5 14.0 20 25.0 E3 A70IQ 3330--0-- 0.033 F 7.5 20.5 15 19.0 E3 A70IQ 3470--0-- 0.047 F 8.5 20.5 15 19.0 E3 A70IQ 3680--0-- 0.068 F 8.5 28.0 10 13.0 E3 A70IT 4100--0-- 0.10 F 10.0 28.0 10 13.0 E3 A70IT 4150--0-- 0.15 F 11.5 28.0 10 13.0 E3 A70IT 4220--0-- 0.22 F 12.5 33.0 6 7.6 E3 A70IT 4330--0-- 0.33 F 15.0 33.0 6 7.6 E3 0.47 F 17.5 33.0 6 7.6 E3 0.68 F 21.0 33.0 6 7.6 E3 Part Number (V2/s) D max 0.010 F 400Vdc/220Vac* D max (V2/s) 0.033 F Rated Cap. Rated Cap. Part Number A70IF 2100--0-- 630Vdc/250Vac* Part Number A70F 1680--0-A70MH 2100--0-A70MH 2150--0-A70MH 2220--0-A70MH 2330--0-A70MH 2470--0-A70MK 2680--0-A70MK 3100--0-- A70MQ3150--0-A70MQ3220--0-A70MQ3330--0-A70MQ3470--0-A70MT 3680--0-A70MT 4100--0-A70MT 4150--0-- Max K0 Part Number (V2/s) A70PF 1100--0-A70PF 1150--0-- A70PF 1220--0-A70PF 1330--0-A70PF 1470--0-A70PH 1680--0-A70PH 2100--0-A70PH 2150--0-A70PH 2220--0-A70PK 2330--0-A70PK 2470--0-A70PQ 2680--0-A70PQ 3100--0-A70PQ 3150--0-A70PT 3220--0-A70PT 3330--0-A70PT 3470--0-A70PT 3680--0-- Mechanical version and packaging (Table1) Internal use Tolerance: J (5%); K (10%); M (20%) Note 1: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse characteristic K0 depends on the voltage wave-form and in any case it cannot overcome the value given in the above table. The dv/dt test is carried out at 2 times the above values. Note 2:Special version for line applications (rated voltage 250 Vac) available upon request. * Not suitable for across-the-line applications. Please refer to Interference Suppression Capacitors (page 145). 65 09/2008 A70 MKP Series METALLIZED POLYPROPYLENE CAPACITOR MULTIPURPOSE APPLICATIONS PRODUCT CODE: A70 test method and performance electrical characteristics Damp heat, steady state: 160 Vdc - 250Vdc Rated voltage (VR): 400 Vdc - 630 Vdc Test conditions Rated temperature (TR): +85C Temperature: Temperature derated voltage: Relative humidity (RH): for temperatures between +85C and +105C a decreasing Test duration: factor of 1.25% per degree C on the rated voltage VR Performance Capacitance change |C/C|: (d.c. and a.c.) has to be applied. DF change (tg): Capacitance range: 1000pF to 4.7F Insulation resistance: Capacitance values: E6 series (IEC 60063 Norm). Capacitance tolerances (measured at 1 kHz): 5% (J); 10% (K); 20% (M). Total self-inductance (L): max 1 nH per 1 mm lead and capacitor length. Dissipation factor (DF): tgx10-4 at +25C 5C kHz 1 10 100 C<0.1 F 06 10 30 0.1 F to 1 F 06 20 2% 10x10-4 at 1kHz 50% of initial limit. Endurance: Test conditions Temperature: Test duration: Voltage applied: Performance +85C2C 2000 h 1.25xVR Capacitance change |C/C|: 3% 10x10-4 at 10kHz for C1F DF change (tg): 10x10-4 att01kHz for C>1F Insulation resistance: 50% of initial limit. >1 F 06 Resistance to soldering heat: Test conditions Insulation resistance: Test conditions Temperature: Voltage charge time: Voltage charge: Performance 1x105 M 30000 s +40C2C 93% 2% 56 days for C 0.33 F for C > 0.33 F Solder bath temperature: +260C5C Dipping time (with heat screen):10 s 1 s +25C 5C 1 min 100Vdc Performance Capacitance change |C/C|: 1% 10x10-4 at 10kHz for C1F DF change (tg): 10x10-4 att01kHz for C>1F Insulation resistance: initial limit. (5x105 M)* (150000 s)* *Typical value Test voltage between terminations: Long term stability (after two years): Storage: standard environmental conditions (see page 12). 1.6xVR applied for 2 s at +25C 5C. Performance Capacitance change |C/C|: 0.5% 09/2008 66 A70 MKP Series METALLIZED POLYPROPYLENE CAPACITOR MULTIPURPOSE APPLICATIONS PRODUCT CODE: A70 MAX. VOLTAGE (Vr.m.s.) VERSUS FREQUENCY (sinusoidal wave-form / Th 40C) 67 09/2008 A70 MKP Series METALLIZED POLYPROPYLENE CAPACITOR MULTIPURPOSE APPLICATIONS PRODUCT CODE: A70 MAX. CURRENT (Ir.m.s.) VERSUS FREQUENCY (sinusoidal wave-form / Th 40C) Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute - and we specifically disclaim - any warranty concerning suitability for a specific customer application or use. This Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained. 09/2008 68