SN54ALVTH162245, SN74ALVTH162245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES331A - APRIL 2000 - REVISED APRIL 2002 D D D D D D D D D D State-of-the-Art Advanced BiCMOS Technology (ABT) Widebus Design for 2.5-V and 3.3-V Operation and Low Static-Power Dissipation Support Mixed-Mode Signal Operation (5-V Input and Output Voltages With 2.3-V to 3.6-V VCC ) Typical VOLP (Output Ground Bounce) <0.8 V at VCC = 3.3 V, TA = 25C High Drive - A Port = -12/12 mA at 3.3-V VCC - B port = -32/64 mA at 3.3-V VCC Ioff and Power-Up 3-State Support Hot Insertion Use Bus Hold on Data Inputs in Place of External Pullup/Pulldown Resistors to Prevent the Bus From Floating A-Port Outputs Have Equivalent 30- Series Resistors, So No External Resistors Are Required Flow-Through Architecture Facilitates Printed Circuit Board Layout Distributed VCC and GND Pins Minimize High-Speed Switching Noise Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II SN54ALVTH162245 . . . WD PACKAGE SN74ALVTH162245 . . . DGG, DGV, OR DL PACKAGE (TOP VIEW) 1DIR 1B1 1B2 GND 1B3 1B4 VCC 1B5 1B6 GND 1B7 1B8 2B1 2B2 GND 2B3 2B4 VCC 2B5 2B6 GND 2B7 2B8 2DIR 1 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 16 33 17 32 18 31 19 30 20 29 21 28 22 27 23 26 24 25 1OE 1A1 1A2 GND 1A3 1A4 VCC 1A5 1A6 GND 1A7 1A8 2A1 2A2 GND 2A3 2A4 VCC 2A5 2A6 GND 2A7 2A8 2OE description The 'ALVTH162245 devices are 16-bit (dual-octal) noninverting 3-state transceivers designed for 2.5-V or 3.3-V VCC operation, but with the capability to provide a TTL interface to a 5-V system environment. These devices can be used as two 8-bit transceivers or one 16-bit transceiver. They allow data transmission from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE) input can be used to disable the device so that the buses are effectively isolated. The A-port outputs, which are designed to source or sink up to 12 mA, include equivalent 30- series resistors to reduce overshoot and undershoot. These devices are fully specified for hot-insertion applications using Ioff and power-up 3-state. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The power-up 3-state circuitry places the outputs in the high-impedance state during power up and power down, which prevents driver conflict. Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus is a trademark of Texas Instruments. Copyright 2002, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SN54ALVTH162245, SN74ALVTH162245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES331A - APRIL 2000 - REVISED APRIL 2002 description (continued) When VCC is between 0 and 1.2 V, the device is in the high-impedance state during power up or power down. However, to ensure the high-impedance state above 1.2 V, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. SN74ALVTH162245 . . . GQL PACKAGE (TOP VIEW) 1 2 3 4 5 terminal assignments 6 A B C D E F G 1 2 3 4 5 6 A 1DIR NC NC NC NC 1OE B 1B2 1B1 GND GND 1A1 1A2 C 1B4 1B3 1A4 1B6 1B5 VCC GND 1A3 D VCC GND 1A5 1A6 E 1B8 1B7 1A7 1A8 F 2B1 2B2 2A2 2A1 G 2B3 2B4 GND GND 2A4 2A3 H 2B5 2B6 2B7 2B8 VCC GND 2A5 J VCC GND 2A6 H 2A8 2A7 J K 2DIR NC NC NC NC 2OE K NC - No internal connection ORDERING INFORMATION TA -40C 40C to 85C -55C to 125C ORDERABLE PART NUMBER PACKAGE TOP-SIDE MARKING SSOP - DL Tape and reel SN74ALVTH162245LR ALVTH162245 TSSOP - DGG Tape and reel SN74ALVTH162245GR ALVTH162245 TVSOP - DGV Tape and reel SN74ALVTH162245VR VT2245 VFBGA - GQL Tape and reel SN74ALVTH162245QR CFP - WD Tube SNJ54ALVTH162245WD SNJ54ALVTH162245WD Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. FUNCTION TABLE (each 8-bit section) INPUTS 2 OPERATION OE DIR L L B data to A bus L H A data to B bus H X Isolation POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ALVTH162245, SN74ALVTH162245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES331A - APRIL 2000 - REVISED APRIL 2002 logic diagram (positive logic) 1DIR 1 2DIR 48 1A1 25 1OE 47 2A1 2 24 2OE 36 13 1B1 To Seven Other Channels 2B1 To Seven Other Channels Pin numbers shown are for the DGG, DGV, DL, and WD packages. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 4.6 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V Voltage range applied to any output in the high-impedance or power-off state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V Voltage range applied to any output in the high state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . -0.5 V to 7 V Output current in the low state, IO: SN54ALVTH162245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 mA SN74ALVTH162245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Output current in the high state, IO: SN54ALVTH162245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -48 mA SN74ALVTH162245 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -64 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50 mA Package thermal impedance, JA (see Note 2): DGG package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70C/W DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58C/W DL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63C/W GQL package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SN54ALVTH162245, SN74ALVTH162245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES331A - APRIL 2000 - REVISED APRIL 2002 recommended operating conditions, VCC = 2.5 V 0.2 V (see Note 3) SN54ALVTH162245 SN74ALVTH162245 MIN MIN VCC VIH Supply voltage 2.3 High-level input voltage 1.7 VIL VI Low-level input voltage IOH IOL TYP MAX 2.7 TYP 2.3 2.7 1.7 0 VCC 5.5 0 VCC V 5.5 V -6 -8 High-level output current (B port) -6 -8 Low-level output current (A port) 6 12 Low-level output current (B port) 6 8 18 24 t/v Input transition rise or fall rate t/VCC TA Power-up ramp rate 200 Operating free-air temperature -55 Outputs enabled 10 10 mA mA ns/V s/V 200 125 V 0.7 High-level output current (A port) Low-level output current; current duty cycle 50%; f 1 kHz (B port) UNIT V 0.7 Input voltage MAX -40 85 C NOTE 3: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. recommended operating conditions, VCC = 3.3 V 0.3 V (see Note 3) SN54ALVTH162245 SN74ALVTH162245 MIN MIN VCC VIH Supply voltage 3 High-level input voltage 2 VIL VI Low-level input voltage IOH IOL TYP MAX 3.6 TYP 3 3.6 2 0 VCC 5.5 0 VCC V 5.5 V -8 -12 High-level output current (B port) -24 -32 Low-level output current (A port) 8 12 Low-level output current (B port) 24 32 Low-level output current; current duty cycle 50%; f 1 kHz (B port) 48 64 10 10 Input transition rise or fall rate t/VCC TA Power-up ramp rate 200 Operating free-air temperature -55 Outputs enabled -40 mA mA ns/V s/V 200 125 V 0.8 High-level output current (A port) t/v UNIT V 0.8 Input voltage MAX 85 C NOTE 3: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ALVTH162245, SN74ALVTH162245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES331A - APRIL 2000 - REVISED APRIL 2002 electrical characteristics over recommended operating free-air temperature range, VCC = 2.5 V 0.2 V (unless otherwise noted) PARAMETER VIK A port VOH VCC = 2.3 V, VCC = 2.3 V to 2.7 V, II = -18 mA IOH = -100 A 3V VCC = 2 2.3 IOH = -6 mA IOH = -8 mA VCC = 2.3 V to 2.7 V, B port VCC = 2 2.3 3V VCC = 2.3 V to 2.7 V, A port VCC = 2 2.3 3V VCC = 2.3 V to 2.7 V, VOL B port 3V VCC = 2 2.3 Control inputs VCC = 2.7 V, VCC = 0 or 2.7 V, A or B ports VCC = 2.7 V II Ioff IBHL IBHH IBHLO IBHHO# IEX|| SN54ALVTH162245 MIN TYP MAX TEST CONDITIONS SN74ALVTH162245 MIN TYP MAX -1.2 -1.2 VCC-0.2 1.7 VCC-0.2 VCC-0.2 1.7 VCC-0.2 1.7 IOH = -100 A IOH = -6 mA IOH = -8 mA IOL = 100 A V V 1.7 0.2 IOL = 6 mA IOL = 12 mA 0.4 IOL = 100 A IOL = 6 mA 0.2 0.2 0.4 0.2 0.4 IOL = 8 mA IOL = 18 mA 0.5 IOL = 24 mA VI = GND 1 1 VI = 5.5 V VI = 5.5 V 10 10 20 20 VI = VCC VI = 0 1 1 -5 -5 V 0.4 0.5 VCC = 0, VCC = 2.3 V, VI or VO = 0 to 4.5 V VI = 0.7 V VCC = 2.3 V, VCC = 2.7 V, VI = 1.7 V VI = 0 to VCC VCC = 2.7 V, VCC = 2.3 V, VI = 0 to VCC VO = 5.5 V 100 115 -10 A A 115 A -10 A 300 300 A -300 -300 A 125 125 A 100 100 A IOZ(PU/PD)k VCC 1.2 V, VO = 0.5 V to VCC, VI = GND or VCC, OE = don't care VCC = 2.7 V, IO = 0, VI = VCC or GND Outputs high 0.04 0.1 0.04 0.1 ICC Outputs low 2.3 4.5 2.3 4.5 Outputs disabled 0.04 0.1 0.04 0.1 VCC = 2.5 V, VCC = 2.5 V, VI = 2.5 V or 0 VO = 2.5 V or 0 3.5 Ci UNIT 3.5 mA pF Cio 8 8 pF All typical values are at VCC = 2.5 V, TA = 25C. The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and then raising it to VIL max. The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and then lowering it to VIH min. An external driver must source at least IBHLO to switch this node from low to high. # An external driver must sink at least IBHHO to switch this node from high to low. || Current into an output in the high state when VO > VCC k High-impedance state during power up or power down PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SN54ALVTH162245, SN74ALVTH162245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES331A - APRIL 2000 - REVISED APRIL 2002 electrical characteristics over recommended operating free-air temperature range, VCC = 3.3 V 0.3 V (unless otherwise noted) PARAMETER VIK A port VOH VCC = 3 V, VCC = 3 V to 3.6 V, II = -18 mA IOH = -100 A VCC = 3 V IOH = -8 mA IOH = -12 mA VCC = 3 V to 3.6 V, B port VCC = 3 V VCC = 3 V to 3.6 V, A port VCC = 3 V VCC = 3 V to 3.6 V, VOL B port VCC = 3 V Control inputs VCC = 3.6 V, VCC = 0 or 3.6 V, A or B ports VCC = 3.6 V II Ioff IBHL IBHH IBHLO IBHHO# IEX|| SN54ALVTH162245 MIN TYP MAX TEST CONDITIONS SN74ALVTH162245 MIN TYP MAX -1.2 -1.2 VCC-0.2 2 VCC-0.2 VCC-0.2 2 VCC-0.2 2 IOH = -100 A IOH = -24 mA IOH = -32 mA IOL = 100 A UNIT V V 2 0.2 IOL = 8 mA IOL = 12 mA ? IOL = 100 A IOL = 24 mA 0.2 0.2 0.8 0.2 0.5 IOL = 32 mA IOL = 48 mA V 0.5 0.55 IOL = 64 mA VI = VCC or GND 0.55 1 1 VI = 5.5 V VI = 5.5 V 10 10 20 20 VI = VCC VI = 0 1 1 -5 -5 VCC = 0, VCC = 3 V, VI or VO = 0 to 4.5 V VI = 0.8 V VCC = 3 V, VCC = 3.6 V, VCC = 3.6 V, VCC = 3 V, 100 A A 75 75 A VI = 2 V VI = 0 to VCC -75 -75 A 500 500 A VI = 0 to VCC VO = 5.5 V -500 -500 A IOZ(PU/PD)k VCC 1.2 V, VO = 0.5 V to VCC, VI = GND or VCC, OE = don't care ICC VCC = 3.6 V, IO = 0, VI = VCC or GND ICCh VCC = 3 V to 3.6 V, One input at VCC - 0.6 V, Other inputs at VCC or GND Ci VCC = 3.3 V, VCC = 3.3 V, 125 125 A 100 100 A Outputs high 0.07 0.1 0.07 0.1 Outputs low 3.2 5 3.2 5 0.07 0.1 0.07 0.1 Outputs disabled VI = 3.3 V or 0 VO = 3.3 V or 0 0.2 3.5 0.2 3.5 mA mA pF Cio 8 8 pF All typical values are at VCC = 3.3 V, TA = 25C. The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and then raising it to VIL max. The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and then lowering it to VIH min. An external driver must source at least IBHLO to switch this node from low to high. # An external driver must sink at least IBHHO to switch this node from high to low. || Current into an output in the high state when VO > VCC k High-impedance state during power up or power down h This is the increase in supply current for each input that is at the specified TTL voltage level rather than VCC or GND. PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SN54ALVTH162245, SN74ALVTH162245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES331A - APRIL 2000 - REVISED APRIL 2002 switching characteristics over recommended operating free-air temperature range, CL = 30 pF, VCC = 2.5 V 0.2 V (unless otherwise noted) (see Figure 1) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A B tPLH tPHL B A tPZH tPZL OE A tPZH tPZL OE B OE A OE B tPHZ tPLZ tPHZ tPLZ SN54ALVTH162245 SN74ALVTH162245 MIN MAX MIN MAX 0.3 3.6 0.3 3.6 0.5 3.5 0.5 3.5 1.1 4.3 1.1 4.3 1.1 3.8 1.1 3.8 2 5.6 2 5.6 1.8 4.4 1.8 4.4 1.5 5.1 1.5 5.1 1.5 4.1 1.5 4.1 1.9 4.9 1.9 4.9 1.5 4.3 1.5 4.3 1.9 4.8 1.9 4.8 1.5 4.1 1.5 4.1 UNIT ns ns ns ns ns ns switching characteristics over recommended operating free-air temperature range, CL = 50 pF, VCC = 3.3 V 0.3 V (unless otherwise noted) (see Figure 2) PARAMETER FROM (INPUT) TO (OUTPUT) tPLH tPHL A B tPLH tPHL B A tPZH tPZL OE A tPZH tPZL OE B OE A OE B tPHZ tPLZ tPHZ tPLZ SN54ALVTH162245 SN74ALVTH162245 MIN MAX MIN MAX 0.5 3.1 0.5 3.1 0.5 3 0.5 3 1 3.7 1 3.7 1 3.4 1 3.4 1.4 4.7 1.4 4.7 1.4 3.9 1.4 3.9 1 3.8 1 3.8 0.7 3.4 0.7 3.4 2.4 5 2.4 5 2.6 4.9 2.6 4.9 2.4 4.7 2.4 4.7 2.3 4.8 2.3 4.8 UNIT ns ns ns ns ns ns PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SN54ALVTH162245, SN74ALVTH162245 2.5-V/3.3-V 16-BIT BUS TRANSCEIVERS WITH 3-STATE OUTPUTS SCES331A - APRIL 2000 - REVISED APRIL 2002 PARAMETER MEASUREMENT INFORMATION 2 x VCC S1 RL From Output Under Test Open GND CL (see Note A) RL TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 2 x VCC GND CL 30 pF 50 pF VCC 2.5 V 0.2 V 3.3 V 0.3 V LOAD CIRCUIT V 0.15 V 0.3 V RL 500 500 VCC Timing Input VCC/2 0V tw tsu VCC VCC/2 Input VCC/2 th VCC VCC/2 Data Input VCC/2 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC VCC/2 Input VCC/2 0V tPHL tPLH Output VCC/2 VOL tPHL VCC/2 tPLZ VCC VCC/2 VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS Output Waveform 2 S1 at GND (see Note B) VOL + V VOL tPHZ tPZH VCC/2 VCC/2 0V Output Waveform 1 S1 at 2 x VCC (see Note B) tPLH VOH Output VCC/2 tPZL VOH VCC/2 VCC Output Control VCC/2 VOH - V VOH 0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR 10 MHz, ZO = 50 , tr 2 ns, tf 2 ns. D. The outputs are measured one at a time with one transition per measurement. E. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 18-Sep-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 74ALVTH162245DLG4 ACTIVE SSOP DL 48 74ALVTH162245GRE4 ACTIVE TSSOP DGG 74ALVTH162245GRG4 ACTIVE TSSOP 74ALVTH162245LRG4 ACTIVE 74ALVTH162245VRE4 25 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SSOP DL 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM ACTIVE TVSOP DGV 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ALVTH162245VRG4 ACTIVE TVSOP DGV 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ALVTH162245DL ACTIVE SSOP DL 48 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ALVTH162245GR ACTIVE TSSOP DGG 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ALVTH162245LR ACTIVE SSOP DL 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74ALVTH162245VR ACTIVE TVSOP DGV 48 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 25 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Aug-2009 TAPE AND REEL INFORMATION *All dimensions are nominal Device SN74ALVTH162245GR Package Package Pins Type Drawing TSSOP SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant DGG 48 2000 330.0 24.4 8.6 15.8 1.8 12.0 24.0 Q1 SN74ALVTH162245LR SSOP DL 48 1000 330.0 32.4 11.35 16.2 3.1 16.0 32.0 Q1 SN74ALVTH162245VR TVSOP DGV 48 2000 330.0 16.4 7.1 10.2 1.6 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Aug-2009 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74ALVTH162245GR TSSOP DGG 48 2000 346.0 346.0 41.0 SN74ALVTH162245LR SSOP DL 48 1000 346.0 346.0 49.0 SN74ALVTH162245VR TVSOP DGV 48 2000 346.0 346.0 33.0 Pack Materials-Page 2 MECHANICAL DATA MSSO001C - JANUARY 1995 - REVISED DECEMBER 2001 DL (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0.025 (0,635) 0.0135 (0,343) 0.008 (0,203) 48 0.005 (0,13) M 25 0.010 (0,25) 0.005 (0,13) 0.299 (7,59) 0.291 (7,39) 0.420 (10,67) 0.395 (10,03) Gage Plane 0.010 (0,25) 1 0-8 24 0.040 (1,02) A 0.020 (0,51) Seating Plane 0.110 (2,79) MAX 0.004 (0,10) 0.008 (0,20) MIN PINS ** 28 48 56 A MAX 0.380 (9,65) 0.630 (16,00) 0.730 (18,54) A MIN 0.370 (9,40) 0.620 (15,75) 0.720 (18,29) DIM 4040048 / E 12/01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15). Falls within JEDEC MO-118 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MTSS003D - JANUARY 1995 - REVISED JANUARY 1998 DGG (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 48 PINS SHOWN 0,27 0,17 0,50 48 0,08 M 25 6,20 6,00 8,30 7,90 0,15 NOM Gage Plane 1 0,25 24 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 48 56 64 A MAX 12,60 14,10 17,10 A MIN 12,40 13,90 16,90 DIM 4040078 / F 12/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MPDS006C - FEBRUARY 1996 - REVISED AUGUST 2000 DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE 24 PINS SHOWN 0,40 0,23 0,13 24 13 0,07 M 0,16 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 0-8 1 0,75 0,50 12 A Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,08 14 16 20 24 38 48 56 A MAX 3,70 3,70 5,10 5,10 7,90 9,80 11,40 A MIN 3,50 3,50 4,90 4,90 7,70 9,60 11,20 DIM 4073251/E 08/00 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side. Falls within JEDEC: 24/48 Pins - MO-153 14/16/20/56 Pins - MO-194 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DLP(R) Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee(R) Solutions amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2009, Texas Instruments Incorporated