Available on Tape and Reel
Operating Temperature: -50oC to +150oC
Storage Temperature: -50oC to +150oC
FR2A-L FR2A 50V 35V 50V
FR2B-L FR2B 100V 70V 100V
FR2D-L FR2D 200V 140V 200V
FR2G-L FR2G 400V 280V 400V
FR2J-L FR2J 600V 420V 600V
FR2K-L FR2K 800V 560V 800V
FR2M-L FR2M 1000V 700V 1000V
Maximum
DC Blocking
Voltage
MCC
Catalog
Number
Device
Marking
Maximum
Recurrent
Peak
Reverse
Volta
g
e
Maximum
RMS
Voltage
Electrical Characteristics @ 25oC Unless Otherwise Specified
Average Forward
Current IF(AV) 2.0A TJ=90oC
Peak Forward
Sur
g
e Current IFSM 50A 8.3ms half sine
Maximum
Instantaneous
Forward Voltage
VF1.30V IFM=2.0A
TA=25oC*
Maximum DC
Reverse Current At
Rated DC Blocking
Voltage
IR 5.0uA TJ=25oC
Maximum Reverse
Recovery Times
FR2A-L~FR2G-L
FR2J-L
FR2K-L~FR2M-L
trr
150ns
250ns
500ns
IF=0.5A,
IR=1.0A,
Irr=0.25A
Typical Junction
Capacitance Cj50pF
Measured at
1.0MHz,
VR=4.0V
Note:1. High Temperature Solder Exemptions Applied, see EU Directive Annex 7.
FR2A-L
THRU
FR2M-L
2.0 Amp Fast
Recovery Rectifier
50 to 1000 Volts
omponents
20736 Marilla Street Chatsworth

 !"#
$%  !"#
MCC
Revision: C 2013/08/20
DO-214AA
(SMB) (LEAD FRAME)
TM
Micro Commercial Components
www.mccsemi.com
1 of 4
• Epoxy meets UL 94 V-0 flammability rating
• Moisture Sensitivity Level 1
• Lead Free Finish/Rohs Compliant (Note1) ("P"Suffix designates
Compliant. See ordering information)
Features
Higher Temp Soldering: 260oC for 10 Seconds At Terminals
*Pulse test: Pulse width 300 usec, duty cycle 2%.
0.050”
0.106”
0.083”
SUGGESTED SOLDER
PAD LAYOUT
A
B
D
C
E
F
G
H
DIMENSIONS
INCHES MM
DIM MIN MAX MIN MAX NOTE
A .160 .180 4.06 4.57
B .130 .155 3.30 3.94
C .006 .012 0.15 0.31
D..030 .060 0.76 1..52
E .205 .220 5.21 5.59
F .079 .103 2.01 2.62
G .077 .087 1.96 2.21
H .002 .008 0.05 0.20
MAX
MIN
MIN
Maximum Ratings
• Halogen free available upon request by adding suffix "-HF"
•
•
FR2A-L thru FR2M-L
Average Forward Rectified Current - Amperes versus
Ambient Temperature - °C
Figure 2
Forward Derating Curve
017550 75 100 125
0
.5
1.0
1.5
Single Phase, Half Wave
60Hz Resistive or Inductive Load
Amps
°C
150
2.0
2.5
3.0
Junction Capacitance - pF versus
Reverse Voltage - Volts
Instantaneous Forward Current - Amperes versus
Instantaneous Forward Voltage - Volts
Figure 1
Typical Forward Characteristics
4
6
20
10
Amps
.4 .6 .8 1.0 12 1.4
.01
.02
.04
.06
.1
.2
.4
.6
1
2
25°C
Volts
Figure 3
Junction Capacitance
.1 .2 1.4 2 10 20 404 100 200
1
2
6
10
20
100
pF
Volts
60
40
4
400 1000
TJ=25°C
MCC
Revision: C 2013/08/20
TM
Micro Commercial Components
www.mccsemi.com
2 of 4
FR2A-L thru FR2M-L
trr
+0.5A
0
-0.25
-1.0
1cm
Set Time Base for 20/100ns/cm
25Vdc
1Ω
50Ω10Ω
Oscilloscope
Note 1
Pulse
Generator
Note 2
Notes:
1. Rise Time = 7ns max.
Input impedance = 1 megohm, 22pF
2. Rise Time = 10ns max.
Source impedance = 50 ohms
3. Resistors are non-inductive
Figure 5
Reverse Recovery Time Characteristic And Test Circuit Diagram
1 100
4
0
15
30
45
8
Figure 4
Maximum Non-Repetitive Forward Surge Current
Peak Forward Surge Current - Amperes versus
Number Of Cycles At 60Hz - Cycles
Amps
Cycles
2610 20 60 80
40
60
75
90
MCC
Revision: C 2013/08/20
TM
Micro Commercial Components
www.mccsemi.com
3 of 4
MCC
Revision: C 2013/08/20
TM
Micro Commercial Components
www.mccsemi.com
4 of 4
Device Packing
FR2A-LTP~FR2M-LTP Tape&Reel: 3Kpcs/Reel
Ordering Information :
***IMPORTANT NOTICE***
Micro Commercial Components Corp. reservesthe right to make changes without further notice to any product herein to
make corrections, modifications , enhancements , improvements , or other changes . Micro Commercial Components
Corp . does not assume any liability arising out of the application or use of any product described herein; neither does it
convey any license under its patent rights ,nor the rights of others . The user of products in such applications shall assume all
risks of such use and will agree to hold Micro Commercial Components Corp . and all the companies whose products are
represented on our website, harmless against all damages.
***LIFE SUPPORT***
MCC's products are not authorized for use as critical components in life support devices or systems without the express written
approval of Micro Commercial Components Corporation.
***CUSTOMER AWARENESS***
Counterfeiting of semiconductor parts is a growing problem in the industry. Micro Commercial Components (MCC) is taking
strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. MCC strongly encourages
customers to purchase MCC parts either directly from MCC or from Authorized MCC Distributors who are listed by country on
our web page cited below. Products customers buy either from MCC directly or from Authorized MCC Distributors are genuine
parts, have full traceability, meet MCC's quality standards for handling and storage. MCC will not provide any warranty
coverage or other assistance for parts bought from Unauthorized Sources. MCC is committed to combat this global
problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized
distributors.