PD - 95129A IRF3205ZPbF IRF3205ZSPbF IRF3205ZLPbF Features l l l l l l HEXFET(R) Power MOSFET Advanced Process Technology Ultra Low On-Resistance 175C Operating Temperature Fast Switching Repetitive Avalanche Allowed up to Tjmax Lead-Free D RDS(on) = 6.5m G Description ID = 75A S This HEXFET(R) Power MOSFET utilizes the latest processing techniques to achieve extremely low on-resistance per silicon area. Additional features of this design are a 175C junction operating temperature, fast switching speed and improved repetitive avalanche rating. These features combine to make this design an extremely efficient and reliable device for use in a wide variety of applications. VDSS = 55V TO-220AB IRF3205ZPbF D2Pak TO-262 IRF3205ZSPbF IRF3205ZLPbF Absolute Maximum Ratings Parameter Max. Units ID @ TC = 25C Continuous Drain Current, VGS @ 10V (Silicon Limited) ID @ TC = 100C Continuous Drain Current, VGS @ 10V 110 ID @ TC = 25C Continuous Drain Current, VGS @ 10V (Package Limited) Pulsed Drain Current IDM 75 440 PD @TC = 25C Power Dissipation 170 W Linear Derating Factor VGS Gate-to-Source Voltage EAS (Thermally limited) Single Pulse Avalanche Energy Single Pulse Avalanche Energy Tested Value EAS (Tested ) 1.1 20 W/C V 180 mJ 78 c d c IAR Avalanche Current EAR Repetitive Avalanche Energy TJ Operating Junction and TSTG Storage Temperature Range -55 to + 175 C Thermal Resistance i Parameter RJC Junction-to-Case RCS Case-to-Sink, Flat Greased Surface RJA Junction-to-Ambient www.irf.com Junction-to-Ambient (PCB Mount) A mJ Mounting Torque, 6-32 or M3 screw i 250 See Fig.12a, 12b, 15, 16 g Soldering Temperature, for 10 seconds RJA h A i j 300 (1.6mm from case ) y y 10 lbf in (1.1N m) Typ. Max. Units --- 0.90 C/W 0.50 --- --- 62 --- 40 1 07/23/10 IRF3205ZS/LPbF Electrical Characteristics @ TJ = 25C (unless otherwise specified) Parameter Min. Typ. Max. Units V(BR)DSS Drain-to-Source Breakdown Voltage 55 --- --- V(BR)DSS/TJ Breakdown Voltage Temp. Coefficient --- 0.051 --- RDS(on) Static Drain-to-Source On-Resistance --- 4.9 6.5 VGS(th) Gate Threshold Voltage 2.0 --- 4.0 gfs IDSS Forward Transconductance 71 --- Drain-to-Source Leakage Current --- --- --- --- 250 Gate-to-Source Forward Leakage --- --- 200 Gate-to-Source Reverse Leakage --- --- -200 IGSS V Conditions VGS = 0V, ID = 250A V/C Reference to 25C, ID = 1mA m VGS = 10V, ID = 66A e V VDS = VGS, ID = 250A --- S VDS = 25V, ID = 66A 20 A VDS = 55V, VGS = 0V VDS = 55V, VGS = 0V, TJ = 125C nA VGS = 20V VGS = -20V Qg Total Gate Charge --- 76 110 Qgs Gate-to-Source Charge --- 21 --- Qgd Gate-to-Drain ("Miller") Charge --- 30 --- VGS = 10V td(on) Turn-On Delay Time --- 18 --- VDD = 28V tr Rise Time --- 95 --- td(off) Turn-Off Delay Time --- 45 --- tf Fall Time --- 67 --- VGS = 10V LD Internal Drain Inductance --- 4.5 --- Between lead, LS Internal Source Inductance --- 7.5 --- 6mm (0.25in.) from package Ciss Input Capacitance --- 3450 --- and center of die contact VGS = 0V Coss Output Capacitance --- 550 --- Crss Reverse Transfer Capacitance --- 310 --- Coss Output Capacitance --- 1940 --- VGS = 0V, VDS = 1.0V, = 1.0MHz Coss Output Capacitance --- 430 --- VGS = 0V, VDS = 44V, = 1.0MHz Coss eff. Effective Output Capacitance --- 640 --- VGS = 0V, VDS = 0V to 44V ID = 66A nC VDS = 44V e ID = 66A ns nH RG = 6.8 e VDS = 25V pF = 1.0MHz f Source-Drain Ratings and Characteristics Parameter Min. Typ. Max. Units IS Continuous Source Current --- --- 75 ISM (Body Diode) Pulsed Source Current --- --- 440 VSD (Body Diode) Diode Forward Voltage --- --- 1.3 V trr Reverse Recovery Time --- 28 42 ns Qrr Reverse Recovery Charge --- 25 38 nC ton Forward Turn-On Time 2 c Conditions MOSFET symbol A showing the integral reverse p-n junction diode. TJ = 25C, IS = 66A, VGS = 0V TJ = 25C, IF = 66A, VDD = 25V di/dt = 100A/s e e Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD) www.irf.com IRF3205ZS/LPbF 1000 10 4.5V 1 0.1 VGS TOP 15V 10V 8.0V 7.0V 6.0V 5.5V 5.0V BOTTOM 4.5V ID, Drain-to-Source Current (A) ID, Drain-to-Source Current (A) 100 1000 VGS TOP 10 100 4.5V 20s PULSE WIDTH Tj = 25C 1 15V 10V 8.0V 7.0V 6.0V 5.5V 5.0V BOTTOM 4.5V 10 100 0.1 1 VDS, Drain-to-Source Voltage (V) 10 100 VDS, Drain-to-Source Voltage (V) Fig 1. Typical Output Characteristics Fig 2. Typical Output Characteristics 1000 120 T J = 25C Gfs, Forward Transconductance (S) ID, Drain-to-Source Current ( A) 20s PULSE WIDTH Tj = 175C T J = 175C 100 10 VDS = 25V 20s PULSE WIDTH 1 4.0 5.0 6.0 7.0 8.0 9.0 10.0 VGS, Gate-to-Source Voltage (V) Fig 3. Typical Transfer Characteristics www.irf.com T J = 175C 100 80 T J = 25C 60 40 20 VDS = 10V 20s PULSE WIDTH 0 11.0 0 20 40 60 80 100 ID, Drain-to-Source Current (A) Fig 4. Typical Forward Transconductance Vs. Drain Current 3 IRF3205ZS/LPbF 6000 20 5000 VGS, Gate-to-Source Voltage (V) VGS = 0V, f = 1 MHZ C iss = C gs + C gd, C ds SHORTED C rss = C gd C, Capacitance (pF) C oss = C ds + C gd 4000 Ciss 3000 2000 1000 Coss Crss VDS= 44V VDS= 28V VDS= 11V 16 12 8 4 0 0 1 ID= 66A 10 0 100 1000.0 10000 ID, Drain-to-Source Current (A) ISD, Reverse Drain Current (A) 60 80 100 120 Fig 6. Typical Gate Charge Vs. Gate-to-Source Voltage Fig 5. Typical Capacitance Vs. Drain-to-Source Voltage OPERATION IN THIS AREA LIMITED BY R DS(on) 1000 TJ = 175C 100.0 40 QG Total Gate Charge (nC) VDS, Drain-to-Source Voltage (V) 100 10.0 T J = 25C 1.0 VGS = 0V 0.1 0.2 0.6 1.0 1.4 1.8 VSD, Source-toDrain Voltage (V) Fig 7. Typical Source-Drain Diode Forward Voltage 4 20 100sec 10 1msec 1 Tc = 25C Tj = 175C Single Pulse 0.1 2.2 1 10msec 10 100 1000 VDS , Drain-toSource Voltage (V) Fig 8. Maximum Safe Operating Area www.irf.com IRF3205ZS/LPbF 120 2.5 RDS(on) , Drain-to-Source On Resistance (Normalized) LIMITED BY PACKAGE ID , Drain Current (A) 100 80 60 40 20 0 25 50 75 100 125 150 175 T C , Case Temperature (C) ID = 66A VGS = 10V 2.0 1.5 1.0 0.5 -60 -40 -20 0 20 40 60 80 100 120 140 160 180 T J , Junction Temperature (C) Fig 10. Normalized On-Resistance Vs. Temperature Fig 9. Maximum Drain Current Vs. Case Temperature 1 Thermal Response ( Z thJC ) D = 0.50 0.20 0.10 0.1 0.05 0.02 0.01 0.01 SINGLE PULSE ( THERMAL RESPONSE ) Notes: 1. Duty Factor D = t1/t2 2. Peak Tj = P dm x Zthjc + Tc 0.001 1E-006 1E-005 0.0001 0.001 0.01 0.1 t1 , Rectangular Pulse Duration (sec) Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case www.irf.com 5 IRF3205ZS/LPbF DRIVER L VDS D.U.T RG 20V VGS + V - DD IAS tp A 0.01 Fig 12a. Unclamped Inductive Test Circuit V(BR)DSS tp EAS, Single Pulse Avalanche Energy (mJ) 350 15V TOP 300 BOTTOM ID 27A 47A 66A 250 200 150 100 50 0 25 50 75 100 125 150 175 Starting T J, Junction Temperature (C) I AS Fig 12c. Maximum Avalanche Energy Vs. Drain Current Fig 12b. Unclamped Inductive Waveforms QG QGS QGD 4.0 VG Charge Fig 13a. Basic Gate Charge Waveform L DUT 0 1K VCC VGS(th) Gate threshold Voltage (V) 10 V ID = 250A 3.0 2.0 1.0 -75 -50 -25 0 25 50 75 100 125 150 175 T J , Temperature ( C ) Fig 13b. Gate Charge Test Circuit 6 Fig 14. Threshold Voltage Vs. Temperature www.irf.com IRF3205ZS/LPbF Avalanche Current (A) 1000 Duty Cycle = Single Pulse 100 Allowed avalanche Current vs avalanche pulsewidth, tav assuming Tj = 25C due to avalanche losses. Note: In no case should Tj be allowed to exceed Tjmax 0.01 0.05 10 0.10 1 0.1 1.0E-08 1.0E-07 1.0E-06 1.0E-05 1.0E-04 1.0E-03 1.0E-02 1.0E-01 tav (sec) Fig 15. Typical Avalanche Current Vs.Pulsewidth EAR , Avalanche Energy (mJ) 200 TOP Single Pulse BOTTOM 10% Duty Cycle ID = 66A 160 120 80 40 0 25 50 75 100 125 150 Starting T J , Junction Temperature (C) Fig 16. Maximum Avalanche Energy Vs. Temperature www.irf.com Notes on Repetitive Avalanche Curves , Figures 15, 16: (For further info, see AN-1005 at www.irf.com) 1. Avalanche failures assumption: Purely a thermal phenomenon and failure occurs at a temperature far in excess of T jmax. This is validated for every part type. 2. Safe operation in Avalanche is allowed as long asTjmax is not exceeded. 3. Equation below based on circuit and waveforms shown in Figures 12a, 12b. 4. PD (ave) = Average power dissipation per single avalanche pulse. 5. BV = Rated breakdown voltage (1.3 factor accounts for voltage increase during avalanche). 6. Iav = Allowable avalanche current. 7. T = Allowable rise in junction temperature, not to exceed Tjmax (assumed as 25C in Figure 15, 16). tav = Average time in avalanche. 175 D = Duty cycle in avalanche = tav *f ZthJC(D, tav ) = Transient thermal resistance, see figure 11) PD (ave) = 1/2 ( 1.3*BV*Iav) = DT/ ZthJC Iav = 2DT/ [1.3*BV*Zth] EAS (AR) = PD (ave)*tav 7 IRF3205ZS/LPbF D.U.T Driver Gate Drive + * * * * D.U.T. ISD Waveform Reverse Recovery Current + dv/dt controlled by RG Driver same type as D.U.T. I SD controlled by Duty Factor "D" D.U.T. - Device Under Test P.W. Period * RG D= VGS=10V Circuit Layout Considerations * Low Stray Inductance * Ground Plane * Low Leakage Inductance Current Transformer - - Period P.W. + VDD + Body Diode Forward Current di/dt D.U.T. VDS Waveform Diode Recovery dv/dt Re-Applied Voltage - Body Diode VDD Forward Drop Inductor Curent Ripple 5% ISD * VGS = 5V for Logic Level Devices Fig 17. Peak Diode Recovery dv/dt Test Circuit for N-Channel HEXFET(R) Power MOSFETs V DS VGS RG RD D.U.T. + -VDD 10V Pulse Width 1 s Duty Factor 0.1 % Fig 18a. Switching Time Test Circuit VDS 90% 10% VGS td(on) tr t d(off) tf Fig 18b. Switching Time Waveforms 8 www.irf.com IRF3205ZS/LPbF TO-220AB Package Outline Dimensions are shown in millimeters (inches) TO-220AB Part Marking Information EXAMPLE: T HIS IS AN IRF1010 LOT CODE 1789 AS S EMBLED ON WW 19, 2000 IN T HE AS S EMBLY LINE "C" Note: "P" in as s embly line pos ition indicates "Lead - Free" INT ERNAT IONAL RECT IFIER LOGO AS S EMBLY LOT CODE PART NUMBER DAT E CODE YEAR 0 = 2000 WEEK 19 LINE C TO-220AB package is not recommended for Surface Mount Application Notes: 1. For an Automotive Qualified version of this part please seehttp://www.irf.com/product-info/auto/ 2. For the most current drawing please refer to IR website at http://www.irf.com/package/ www.irf.com 9 IRF3205ZS/LPbF D2Pak (TO-263AB) Package Outline Dimensions are shown in millimeters (inches) D2Pak (TO-263AB) Part Marking Information T HIS IS AN IRF530S WIT H LOT CODE 8024 ASSE MB LED ON WW 02, 2000 IN THE AS SEMBLY LINE "L" INTE RNATIONAL RE CTIFIER LOGO AS SEMBLY LOT CODE PART NUMBER F 530S DATE CODE YEAR 0 = 2000 WEEK 02 LINE L OR INTE RNATIONAL RECTIF IER LOGO ASS EMBLY LOT CODE PART NUMBER F530S DATE CODE P = DES IGNAT ES LEAD - F REE PRODUCT (OPTIONAL) YEAR 0 = 2000 WEEK 02 A = ASSE MBLY SIT E CODE Notes: 1. For an Automotive Qualified version of this part please seehttp://www.irf.com/product-info/auto/ 2. For the most current drawing please refer to IR website at http://www.irf.com/package/ 10 www.irf.com IRF3205ZS/LPbF TO-262 Package Outline Dimensions are shown in millimeters (inches) TO-262 Part Marking Information EXAMPLE : T HIS IS AN IRL3103L LOT CODE 1789 AS SEMBLED ON WW 19, 1997 IN T HE ASSEMBLY LINE "C" Note: "P" in assembly line position indicates "Lead-F ree" INT E RNAT IONAL RECT IFIER LOGO ASSE MBLY LOT CODE PART NUMBER DAT E CODE YE AR 7 = 1997 WEEK 19 LINE C OR INTE RNAT IONAL RECT IFIER LOGO ASSE MBLY LOT CODE PART NUMBE R DAT E CODE P = DE SIGNAT ES LEAD-FREE PRODUCT (OPTIONAL) YEAR 7 = 1997 WEEK 19 A = ASSEMBLY SITE CODE Notes: 1. For an Automotive Qualified version of this part please seehttp://www.irf.com/product-info/auto/ 2. For the most current drawing please refer to IR website at http://www.irf.com/package/ www.irf.com 11 IRF3205ZS/LPbF D2Pak Tape & Reel Infomation Dimensions are shown in millimeters (inches) TRR 1.60 (.063) 1.50 (.059) 4.10 (.161) 3.90 (.153) FEED DIRECTION 1.85 (.073) 1.65 (.065) 1.60 (.063) 1.50 (.059) 11.60 (.457) 11.40 (.449) 0.368 (.0145) 0.342 (.0135) 15.42 (.609) 15.22 (.601) 24.30 (.957) 23.90 (.941) TRL 10.90 (.429) 10.70 (.421) 1.75 (.069) 1.25 (.049) 4.72 (.136) 4.52 (.178) 16.10 (.634) 15.90 (.626) FEED DIRECTION 13.50 (.532) 12.80 (.504) 27.40 (1.079) 23.90 (.941) 4 330.00 (14.173) MAX. Notes: 60.00 (2.362) MIN. NOTES : 1. COMFORMS TO EIA-418. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION MEASURED @ HUB. 4. INCLUDES FLANGE DISTORTION @ OUTER EDGE. 26.40 (1.039) 24.40 (.961) 3 30.40 (1.197) MAX. 4 Repetitive rating; pulse width limited by Limited by T Jmax , see Fig.12a, 12b, 15, 16 for typical repetitive max. junction temperature. (See fig. 11). avalanche performance. Limited by TJmax, starting TJ = 25C, L = 0.08mH This value determined from sample failure population. 100% RG = 25, IAS = 66A, VGS =10V. Part not tested to this value in production. recommended for use above this value. This is only applied to TO-220AB pakcage. Pulse width 1.0ms; duty cycle 2%. This is applied to D2Pak, when mounted on 1" square PCB (FR Coss eff. is a fixed capacitance that gives the 4 or G-10 Material). For recommended footprint and soldering same charging time as Coss while VDS is rising techniques refer to application note #AN-994. from 0 to 80% VDSS . Data and specifications subject to change without notice. This product has been designed and qualified for the Industrial market. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information. 07/2010 12 www.irf.com