MOTOROLA SEMICONDUCTOR TECHNICAL DATA Field-effect current regulator diodes are circuit elements that provide a current essentially independent of voltage. These diodes are especially designed for maximum impedance over the operating range. These devices may be used in parallel to obtain higher currents. Manufacturing Locations: WAFER FAB: Phoenix, Arizona ASSEMBLY/TEST: Phoenix, Arizona CURRENT REGULATOR DIODES CASE 51-02 MAXIMUM RATINGS Rating Peak Operating Voltage (TJ = -55C to +200C) Symbol Value Unit POV 100 Volts 600 4.8 mW mW/C -55 to +200 C Steady State Power Dissipation @ TL = 75C Derate above TL = 75C Lead Length = 3/8 (Forward or Reverse Bias) PD Operating and Storage Junction Temperature Range TJ, Tstg 1.5 Watt DC Power Data Sheet 9-2 Motorola TVS/Zener Device Data 1N5283 through 1N5314 ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) Type No. Nom Min Max Minimum Dynamic Impedance @ VT = 25 V ZT (M) 1N5283 1N5284 1N5285 1N5286 1N5287 0.22 0.24 0.27 0.30 0.33 0.198 0.216 0.243 0.270 0.297 0.242 0.264 0.297 0.330 0.363 25.0 19.0 14.0 9.00 6.60 2.75 2.35 1.95 1.60 1.35 1.00 1.00 1.00 1.00 1.00 1N5288 1N5289 1N5290 1N5291 1N5292 0.39 0.43 0.47 0.56 0.62 0.351 0.387 0.423 0.504 0.558 0.429 0.473 0.517 0.616 0.682 4.10 3.30 2.70 1.90 1.55 1.00 0.870 0.750 0.560 0.470 1.05 1.05 1.05 1.10 1.13 1N5293 1N5294 1N5295 1N5296 1N5297 0.68 0.75 0.82 0.91 1.00 0.612 0.675 0.738 0.819 0.900 0.748 0.825 0.902 1.001 1.100 1.35 1.15 1.00 0.880 0.800 0.400 0.335 0.290 0.240 0.205 1.15 1.20 1.25 1.29 1.35 1N5298 1N5299 1N5300 1N5301 1N5302 1.10 1.20 1.30 1.40 1.50 0.990 1.08 1.17 1.26 1.35 1.21 1.32 1.43 1.54 1.65 0.700 0.640 0.580 0.540 0.510 0.180 0.155 0.135 0.115 0.105 1.40 1.45 1.50 1.55 1.60 1N5303 1N5304 1N5305 1N5306 1N5307 1.60 1.80 2.00 2.20 2.40 1.44 1.62 1.80 1.98 2.16 1.76 1.98 2.20 2.42 2.64 0.475 0.420 0.395 0.370 0.345 0.092 0.074 0.061 0.052 0.044 1.65 1.75 1.85 1.95 2.00 1N5308 1N5309 1N5310 1N5311 1N5312 2.70 3.00 3.30 3.60 3.90 2.43 2.70 2.97 3.24 3.51 2.97 3.30 3.63 3.96 4.29 0.320 0.300 0.280 0.265 0.255 0.035 0.029 0.024 0.020 0.017 2.15 2.25 2.35 2.50 2.60 1N5313 1N5314 4.30 4.70 3.87 4.23 4.73 5.17 0.245 0.235 0.014 0.012 2.75 2.90 Regulator Current IP (mA) @ VT = 25 V Minimum Knee Impedance @ VK = 6.0 V ZK (M) Maximum Limiting Voltage @ IL = 0.8 IP (min) VL (Volts) Devices listed in bold, italic are Motorola preferred devices. Motorola TVS/Zener Device Data 1.5 Watt DC Power Data Sheet 9-3 1N5283 through 1N5314 5 ZK @ VK FORWARD 3 2 SYMBOLS AND DEFINITIONS IP & ZT @ VT VL @ IL 1 ID -- Diode Current. IL -- Limiting Current: 80% of IP minimum used to determine Limiting voltage, VL. IP -- Pinch-off Current: Regulator current at specified Test Voltage, VT. POV -- Peak Operating Voltage: Maximum voltage to be applied to device. l -- Current Temperature Coefficient. VAK -- Anode-to-cathode Voltage. VK -- Knee Impedance Test Voltage: Specified voltage used to establish Knee Impedance, ZK. VL -- Limiting Voltage: Measured at IL, VL, together with Knee AC Impedance, ZK, indicates the Knee characteristics of the device. VT -- Test Voltage: Voltage at which IP and ZT are specified. ZK -- Knee AC Impedance at Test Voltage: To test for ZK, a 90 Hz signal VK with RMS value equal to 10% of test voltage, VK, is superimposed on VK: ZK = VK/iK where iK is the resultant ac current due to VK. To provide the most constant current from the diode, ZK should be as high as possible; therefore, a minimum value of ZK is specified. ZT -- AC Impedance at Test Voltage: Specified as a minimum value. To test for ZT, a 90 Hz signal with RMS value equal to 10% of Test Voltage VT, is superimposed on VT. POV 0 REVERSE ID, DIODE CURRENT (mA) 4 -20 -40 + -60 REVERSE -80 -100 -2 -1 0 FORWARD 20 40 60 - ANODE 80 100 CATHODE 120 140 160 VAK, ANODE-CATHODE VOLTAGE (VOLTS) JL , JUNCTION-TO-LEAD THERMAL RESISTANCE (C/W) Figure 1. Typical Current Regulator Characteristics 300 250 APPLICATION NOTE 200 POINT OF LEAD TEMPERATURE MEASUREMENT 150 L L (MOST HEAT CONDUCTION IS THROUGH THE CATHODE LEAD) 100 50 As the current available from the diode is temperature dependent, it is necessary to determine junction temperature, TJ, under specific operating conditions to calculate the value of the diode current. The following procedure is recommended: Lead Temperature, TL, shall be determined from: TL = LA PD + TA where LA is lead-to-ambient thermal resistance and PD is power dissipation. LA is generally 30-40C/W for the various clips and tie points in common use, and for printed circuit-board wiring. Junction Temperature, TJ, shall be calculated from: TJ = TL + JL PD where JL is taken from Figure 2. For circuit design limits of VAK, limits of PD may be estimated and extremes of TJ may be computed. Using the information on Figures 4 and 5, changes in current may be found. To improve current regulation, keep VAK low to reduce PD and keep the leads short, especially the cathode lead, to reduce JL. 0 0.2 0.4 0.6 0.8 1 L, LEAD LENGTH (INCHES) ID, FORWARD DIODE CURRENT (mA) Figure 2. Typical Thermal Resistance 10 7 5 3 2 TJ = 25C POV = 100 V 1N5313 1N5309 (DATA OBTAINED FROM PULSE TESTS) 1N5305 1 1N5298 0.7 0.5 1N5290 0.3 0.2 0.1 0.1 0.2 0.3 0.5 0.7 1 2 3 5 7 10 20 30 50 70 100 VAK, ANODE-CATHODE VOLTAGE (VOLTS) Figure 3. Typical Forward Characteristics 1.5 Watt DC Power Data Sheet 9-4 Motorola TVS/Zener Device Data I , TEMPERATURE COEFFICIENT (%/ C) 1N5283 through 1N5314 0.7 0.6 0.5 TJ = +25C TO +150C VAK = 25 V IP = I IP(nom) TJ (C) 100 0.4 0.3 0.2 0.1 0 -0.1 RANGE* TYPICAL -0.2 -0.3 -0.4 -0.5 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 2 3 4 5 IP, NOMINAL PINCH-OFF CURRENT (mA) Figure 4. Temperature Coefficient I , TEMPERATURE COEFFICIENT (%/ C) 1 0.8 TJ = -55C TO +25C VAK = 25 V IP = I IP(nom) TJ (C) 100 0.6 0.4 0.2 RANGE* 0 TYPICAL -0.2 -0.4 -0.6 -0.8 -1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 2 3 4 5 3 4 5 IP, NOMINAL PINCH-OFF CURRENT (mA) Figure 5. Temperature Coefficient IP , CURRENT CHANGE (mA) 0.1 0 -0.1 -0.2 -0.3 -0.4 -0.5 -0.6 -0.7 TYPICAL RANGE* -0.8 -0.9 -1 -1.1 0.2 TA = 25C VAK = 40 V, VAK VARIED FROM 10 V TO 50 V IP = IP @ 50 V - IP @ 10 V 1/2 LEAD LENGTH, LA = 30C/W 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1 2 IP, NOMINAL PINCH-OFF CURRENT (mA) *90% of the units will be in the ranges shown. Figure 6. Current Regulation Factor Devices listed in bold, italic are Motorola preferred devices. Motorola TVS/Zener Device Data 1.5 Watt DC Power Data Sheet 9-5 1N5283 through 1N5314 Current Regulator Diodes -- Axial Leaded 1.5 Watt DC Power B NOTES: 1. PACKAGE CONTOUR OPTIONAL WITHIN DIA B AND LENGTH A. HEAT SLUGS, IF ANY, SHALL BE INCLUDED WITHIN THIS CYLINDER, BUT SHALL NOT BE SUBJECT TO THE MIN LIMIT OF DIA B. 2. LEAD DIA NOT CONTROLLED IN ZONES F, TO ALLOW FOR FLASH, LEAD FINISH BUILDUP, AND MINOR IRREGULARITIES OTHER THAN HEAT SLUGS. D K F A DIM A B D F K F K MILLIMETERS MIN MAX 5.84 7.62 2.16 2.72 0.46 0.56 -- 1.27 25.40 38.10 INCHES MIN MAX 0.230 0.300 0.085 0.107 0.018 0.022 -- 0.050 1.000 1.500 All JEDEC dimensions and notes apply CASE 51-02 DO-204AA GLASS (Refer to Section 10 for Surface Mount, Thermal Data and Footprint Information.) MULTIPLE PACKAGE QUANTITY (MPQ) REQUIREMENTS Package Option Type No. Suffix MPQ (Units) RL 2.5K (None) 500 Tape and Reel Bulk (Refer to Section 10 for more information on Packaging Specifications.) Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. 1.5 Watt DC Power Data Sheet 9-6 Motorola TVS/Zener Device Data