09/2008 64
A70
MKP Series
METALLIZED POLYPROPYLENE CAPACITOR
MULTIPURPOSE APPLICATIONS
Typical applications: temperature compensation circuits,
timing, oscillator circuits, power factor correction and
coupling capacitor in SMPS applications.
PRODUCT CODE: A70
GENERAL TECHNICAL DATA
Dielectric: polypropylene lm.
Plates: aluminium layer deposited by evaporation under
vacuum.
Winding: non-inductive type.
Leads: tinned wire.
Protection: polyester tape wrapping and thermosetting resin
end ll.
Marking: Manufacturer’s logo, series (1.70), dielectric
code (MKP), capacitance, tolerance, D.C. rated
voltage.
Climatic category: 55/105/56 IEC 60068-1
Operating temperature range: -55 to +105°C
Related documents: IEC 60384-16
Loose Taped
PRODUCT CODE SYSTEM
The part number, comprising 14 digits, is formed as follows:
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A 7 0 -
Digit 1 to 3 Series code.
Digit 4 d.c. rated voltage:
G = 160V I = 250V M = 400V P = 630V
Digit 5 Length (mm):
F=11; H=14; K=20.5; Q=28; T=33
Digit 6 to 9 Digits 7 - 8 - 9 indicate the rst three digits of
Capacitance value and the 6th digit indicates
the number of zeros that must be added to
obtain the Rated Capacitance in pF.
Digit 10 to 11 Mechanical version and/or packaging (table1)
Digit 12 Identies the dimensions and electrical
characteristics.
Digit 13 Internal use
Digit 14 Capacitance tolerance:
J=5%; K=10%; M=20%.
Table 1 (for more detailed information, please refer to page 14).
Standard
packaging style
Ordering code
(Digit 10 to 11)
Reel Ø 355 mm 26
Loose AA
single sided metallized
polypropylene lm
Winding scheme
D max 5 >5 ≤ 7 >7<16 ≥16
Ød ±0.05 0.5 0.6 0.8 1
All dimensions are in mm.
09/2008
65
Rated
Cap.
400Vdc/220Vac* Max
dv/dt
Max K0Part Number
D max L max (V/µs) (V2/µs)
6800 pF 5.0 11.0 25.0 20.0 E3 A70ΜF 1680--0--
0.010 µF 5.5 14.0 13.5 11.0 E3 A70MH 2100--0--
0.015 µF 6.0 14.0 13.5 11.0 E3 A70MH 2150--0--
0.022 µF 6.0 14.0 13.5 11.0 E3 A70MH 2220--0--
0.033 µF 6.5 14.0 13.5 11.0 E3 A70MH 2330--0--
0.047 µF 8.0 14.0 13.5 11.0 E3 A70MH 2470--0--
0.068 µF 7.0 20.5 10.0 8.0 E3 A70MK 2680--0--
0.10 µF 8.0 20.5 10.0 8.0 E3 A70MK 3100--0--
0.15 µF 8.0 28.0 6.5 5.2 E3 A70MQ3150--0--
0.22 µF 9.5 28.0 6.5 5.2 E3 A70MQ3220--0--
0.33 µF 11.0 28.0 6.5 5.2 E3 A70MQ3330--0--
0.47 µF 13.0 28.0 6.5 5.2 E3 A70MQ3470--0--
0.68 µF 13.5 33.0 4.0 3.2 E3 A70MT 3680--0--
1.0 µF 16.5 33.0 4.0 3.2 E3 A70MT 4100--0--
1.5 µF 20.0 33.0 4.0 3.2 E3 A70MT 4150--0--
Rated
Cap.
630Vdc/250Vac* Max
dv/dt
Max K0Part Number
D max L max (V/µs) (V2/µs)
1000 pF 5.0 11.0 30 38.0 E3 A70PF 1100--0--
1500 pF 5.0 11.0 30 38.0 E3 A70PF 1150--0--
2200 pF 5.0 11.0 30 38.0 E3 A70PF 1220--0--
3300 pF 5.0 11.0 30 38.0 E3 A70PF 1330--0--
4700 pF 5.0 11.0 30 38.0 E3 A70PF 1470--0--
6800 pF 5.5 14.0 20 25.0 E3 A70PH 1680--0--
0.010 µF 6.0 14.0 20 25.0 E3 A70PH 2100--0--
0.015 µF 7.0 14.0 20 25.0 E3 A70PH 2150--0--
0.022 µF 8.5 14.0 20 25.0 E3 A70PH 2220--0--
0.033 µF 7.5 20.5 15 19.0 E3 A70PK 2330--0--
0.047 µF 8.5 20.5 15 19.0 E3 A70PK 2470--0--
0.068 µF 8.5 28.0 10 13.0 E3 A70PQ 2680--0--
0.10 µF 10.0 28.0 10 13.0 E3 A70PQ 3100--0--
0.15 µF 11.5 28.0 10 13.0 E3 A70PQ 3150--0--
0.22 µF 12.5 33.0 6 7.6 E3 A70PT 3220--0--
0.33 µF 15.0 33.0 6 7.6 E3 A70PT 3330--0--
0.47 µF 17.5 33.0 6 7.6 E3 A70PT 3470--0--
0.68 µF 21.0 33.0 6 7.6 E3 A70PT 3680--0--
Rated
Cap.
160Vdc/90Vac Max
dv/dt
Max K0Part Number
D max L max (V/µs) (V2/µs)
0.022 µF 5.0 11.0 5 1.60 E3 A70GF 2220--0--
0.033 µF 5.0 11.0 5 1.60 E3 A70GF 2330--0--
0.047 µF 5.0 11.0 5 1.60 E3 A70GF 2470--0--
0.068 µF 5.5 14.0 5 1.60 E3 A70GH 2680--0--
0.10 µF 5.5 14.0 5 1.60 E3 A70GH 3100--0--
0.15 µF 6.5 14.0 5 1.60 E3 A70GH 3150--0--
0.22 µF 7.5 14.0 5 1.60 E3 A70GH 3220--0--
0.33 µF 7.0 20.5 3 0.96 E3 A70GK 3330--0--
0.47 µF 8.0 20.5 3 0.96 E3 A70GK 3470--0--
0.68 µF 8.0 28.0 2 0.64 E3 A70GQ 3680--0--
1.0 µF 9.5 28.0 2 0.64 E3 A70GQ 4100--0--
1.5 µF 11.0 28.0 2 0.64 E3 A70GQ 4150--0--
2.2 µF 12.0 33.0 1 0.32 E3 A70GT 4220--0--
3.3 µF 14.5 33.0 1 0.32 E3 A70GT 4330--0--
4.7 µF 17.0 33.0 1 0.32 E3 A70GT 4470--0--
Rated
Cap.
250Vdc/200Vac Max
dv/dt
Max K0Part Number
D max L max (V/µs) (V2/µs)
0.010 µF 5.0 11.0 11.0 5.5 E3 A70IF 2100--0--
0.015 µF 5.0 11.0 11.0 5.5 E3 A70IF 2150--0--
0.022 µF 5.5 14.0 10.0 5.0 E3 A70IH 2220--0--
0.033 µF 5.5 14.0 10.0 5.0 E3 A70IH 2330--0--
0.047 µF 6.0 14.0 10.0 5.0 E3 A70IH 2470--0--
0.068 µF 7.0 14.0 10.0 5.0 E3 A70IH 2680--0--
0.10 µF 8.5 14.0 10.0 5.0 E3 A70IH 3100--0--
0.15 µF 7.5 20.5 7.0 3.5 E3 A70IK 3150--0--
0.22 µF 9.0 20.5 7.0 3.5 E3 A70IK 3220--0--
0.33 µF 8.5 28.0 4.0 2.0 E3 A70IQ 3330--0--
0.47 µF 10.0 28.0 4.0 2.0 E3 A70IQ 3470--0--
0.68 µF 11.5 28.0 4.0 2.0 E3 A70IQ 3680--0--
1.0 µF 12.5 33.0 2.5 1.3 E3 A70IT 4100--0--
1.5 µF 15.0 33.0 2.5 1.3 E3 A70IT 4150--0--
2.2 µF 18.0 33.0 2.5 1.3 E3 A70IT 4220--0--
3.3 µF 21.5 33.0 2.5 1.3 E3 A70IT 4330--0--
A70
MKP Series
METALLIZED POLYPROPYLENE CAPACITOR
MULTIPURPOSE APPLICATIONS
PRODUCT CODE: A70
All dimensions are in mm.
Note 1: If the working voltage (V) is lower than the rated voltage (VR), the capacitor may work at higher dv/dt. In this case
the maximum value allowed is obtained multiplying the above value (see table dv/dt) with the ratio VR /V. The pulse
characteristic K0 depends on the voltage wave-form and in any case it cannot overcome the value given in the above
table. The dv/dt test is carried out at 2 times the above values.
Note 2: Special version for line applications (rated voltage 250 Vac) available upon request.
* Not suitable for across-the-line applications. Please refer to Interference Suppression Capacitors (page 145).
Mechanical version and packaging (Table1)
Internal use
Tolerance: J (±5%); K (±10%); M (±20%) Mechanical version and packaging (Table1)
Internal use
Tolerance: J (±5%); K (±10%); M (±20%)
09/2008 66
TEST METHOD AND PERFORMANCE
Damp heat, steady state:
Test conditions
Temperature: +40°C±2°C
Relative humidity (RH): 93% ±2%
Test duration: 56 days
Performance
Capacitance change |∆C/C|: ≤2%
DF change (∆tgδ): ≤10x10-4 at 1kHz
Insulation resistance: ≥50% of initial limit.
Endurance:
Test conditions
Temperature: +85°C±2°C
Test duration: 2000 h
Voltage applied: 1.25xVR
Performance
Capacitance change |∆C/C|: ≤3%
DF change (∆tgδ): ≤10x10-4 at 10kHz for C≤1µF
≤10x10-4 att01kHz for C>1µF
Insulation resistance: ≥50% of initial limit.
Resistance to soldering heat:
Test conditions
Solder bath temperature: +260°C±5°C
Dipping time (with heat screen):10 s ±1 s
Performance
Capacitance change |∆C/C|: ≤1%
DF change (∆tgδ): ≤10x10-4 at 10kHz for C≤1µF
≤10x10-4 att01kHz for C>1µF
Insulation resistance: ≥ initial limit.
Long term stability (after two years):
Storage: standard environmental conditions (see page 12).
Performance
Capacitance change |∆C/C|: ≤0.5%
ELECTRICAL CHARACTERISTICS
Rated voltage (VR): 160 Vdc - 250Vdc
400 Vdc - 630 Vdc
Rated temperature (TR): +85°C
Temperature derated voltage:
for temperatures between +85°C and +105°C a decreasing
factor of 1.25% per degree °C on the rated voltage VR
(d.c. and a.c.) has to be applied.
Capacitance range: 1000pF to 4.7µF
Capacitance values:
E6 series (IEC 60063 Norm).
Capacitance tolerances (measured at 1 kHz):
±5% (J); ±10% (K); ±20% (M).
Total self-inductance (L):
max 1 nH per 1 mm lead and capacitor length.
Dissipation factor (DF):
tgδx10-4 at +25°C ±5°C
kHz C<0.1 µF 0.1 µF to 1 µF >1 µF
1
10
100
≤06
≤10
≤30
≤06
≤20
≤06
Insulation resistance:
Test conditions
Temperature: +25°C± 5°C
Voltage charge time: 1 min
Voltage charge: 100Vdc
Performance
≥1x105 MΩ for C ≤ 0.33 µF (5x105 MΩ)*
≥30000 s for C > 0.33 µF (150000 s)*
*Typical value
Test voltage between terminations:
1.6xVR applied for 2 s at +25°C ±5°C.
A70
MKP Series
METALLIZED POLYPROPYLENE CAPACITOR
MULTIPURPOSE APPLICATIONS
PRODUCT CODE: A70
09/2008
67
MAX. VOLTAGE (Vr.m.s.) VERSUS FREQUENCY (sinusoidal wave-form / Th ≤ 40°C)
A70
MKP Series
METALLIZED POLYPROPYLENE CAPACITOR
MULTIPURPOSE APPLICATIONS
PRODUCT CODE: A70
09/2008 68
MAX. CURRENT (Ir.m.s.) VERSUS FREQUENCY (sinusoidal wave-form / Th ≤ 40°C)
A70
MKP Series
METALLIZED POLYPROPYLENE CAPACITOR
MULTIPURPOSE APPLICATIONS
PRODUCT CODE: A70