Product Folder Sample & Buy Support & Community Tools & Software Technical Documents LM833 SLOS481B - JULY 2010 - REVISED OCTOBER 2014 LM833 Dual High-Speed Audio Operational Amplifier 1 Features 3 Description * * * * * * * * * * The LM833 device is a dual operational amplifier with high-performance specifications for use in quality audio and data-signal applications. Dual amplifiers are utilized widely in audio circuits optimized for all preamp and high level stages in PCM and HiFi systems. The LM833 device is pin-for-pin compatible with industry-standard dual operation amplifiers. With addition of a preamplifier, the gain of the power stage can be greatly reduced to improve performance. 1 Dual-Supply Operation: 5 V to 18 V Low Noise Voltage: 4.5 nV/Hz Low Input Offset Voltage: 0.15 mV Low Total Harmonic Distortion: 0.002% High Slew Rate: 7 V/s High-Gain Bandwidth Product: 16 MHz High Open-Loop AC Gain: 800 at 20 kHz Large Output-Voltage Swing: -14.6 V to 14.1 V Excellent Gain and Phase Margins Available in 8-Terminal MSOP Package (3.0 mm x 4.9 mm x 0.65 mm) Device Information PART NUMBER LM833 2 Applications * * * * * PACKAGE BODY SIZE (NOM) SOIC (8) 4.90 mm x 3.91 mm VSSOP (8) 3.00 mm x 3.00 mm PDIP (8) 9.81 mm x 6.35 mm HiFi Audio System Equipment Preamplification and Filtering Set-Top Box Microphone Preamplifier Circuit General-Purpose Amplifier Applications 4 Typical Design Example Audio Pre-Amplifier +VCC 750 47 F Audio Input 0.1 F 1000 1 F 47 k 0.0022 F 2.7 k OUT1 VCC+ 2.7 k IN1 0.001 F 0.1 F OUT2 IN1+ IN2 VCC IN2+ 10 k 47 F 750 VEE 12 V / 1 W 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LM833 SLOS481B - JULY 2010 - REVISED OCTOBER 2014 www.ti.com Table of Contents 1 2 3 4 5 6 7 8 Features .................................................................. Applications ........................................................... Description ............................................................. Typical Design Example Audio Pre-Amplifier..... Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 1 2 3 4 7.1 7.2 7.3 7.4 7.5 7.6 7.7 4 4 4 4 5 5 6 Absolute Maximum Ratings ..................................... Handling Ratings....................................................... Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... Operating Characteristics.......................................... Typical Characteristics .............................................. Detailed Description ............................................ 13 8.1 Overview ................................................................. 13 8.2 Functional Block Diagram ....................................... 13 8.3 Feature Description................................................. 14 8.4 Device Functional Modes........................................ 14 9 Application and Implementation ........................ 15 9.1 Application Information............................................ 15 9.2 Typical Application ................................................. 15 9.3 Typical Application -- Reducing Oscillation from High-Capacitive Loads............................................. 18 10 Power Supply Recommendations ..................... 20 11 Layout................................................................... 20 11.1 Layout Guidelines ................................................. 20 11.2 Layout Example .................................................... 20 12 Device and Documentation Support ................. 22 12.1 Trademarks ........................................................... 22 12.2 Electrostatic Discharge Caution ............................ 22 12.3 Glossary ................................................................ 22 13 Mechanical, Packaging, and Orderable Information ........................................................... 23 5 Revision History Changes from Revision A (August 2010) to Revision B Page * Updated document to new TI data sheet format. ................................................................................................................... 1 * Deleted Ordering Information table. ....................................................................................................................................... 1 * Added Device Information table. ............................................................................................................................................ 1 * Added Pin Functions table. .................................................................................................................................................... 3 * Added Handling Ratings table. ............................................................................................................................................... 4 * Added Thermal Information table. .......................................................................................................................................... 4 * Added Power Supply Recommendations, Layout, Device and Documentation Support, and Mechanical, Packaging, and Orderable Information sections .................................................................................................................................... 20 Changes from Original (July 2010) to Revision A * 2 Page Changed data sheet status from Product Preview to Production Data. ................................................................................. 1 Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 LM833 www.ti.com SLOS481B - JULY 2010 - REVISED OCTOBER 2014 6 Pin Configuration and Functions D (SOIC), DGK (MSOP), OR P (PDIP) PACKAGE (TOP VIEW) OUT1 1 8 VCC+ IN1- 2 7 OUT2 IN1+ 3 6 IN2- VCC- 4 5 IN2+ Pin Functions PIN NAME NO. TYPE DESCRIPTION IN1+ 3 Input Noninverting input IN1- 2 Input Inverting Input IN2+ 5 Input Noninverting input IN2- 6 Input Inverting Input OUT1 1 Output Output 1 OUT2 7 Output Output 2 VCC+ 8 -- Positive Supply VCC- 4 -- Negative Supply Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 3 LM833 SLOS481B - JULY 2010 - REVISED OCTOBER 2014 www.ti.com 7 Specifications 7.1 Absolute Maximum Ratings over operating free-air temperature range (unless otherwise noted) (1) MIN MAX UNIT VCC+ Supply voltage (2) 18 V VCC- Supply voltage (2) -18 V VCC+ - VCC- Supply voltage 36 V VCC+ V 10 mA Input voltage, either input (2) (3) Input current VCC- (4) Duration of output short circuit (5) TJ (1) (2) (3) (4) (5) Unlimited Operating virtual junction temperature 150 C Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC-. The magnitude of the input voltage must never exceed the magnitude of the supply voltage. Excessive input current will flow if a differential input voltage in excess of approximately 0.6 V is applied between the inputs, unless some limiting resistance is used. The output may be shorted to ground or either power supply. Temperature and/or supply voltages must be limited to ensure the maximum dissipation rating is not exceeded. 7.2 Handling Ratings PARAMETER Tstg MIN MAX UNIT C Storage temperature range V(ESD) (1) (2) DEFINITION -65 150 Human-Body Model (HBM) (1) 0 2.5 Charged-Device Model (CDM) (2) 0 1.5 kV JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. 7.3 Recommended Operating Conditions VCC- VCC+ TA MIN MAX -5 -18 5 18 -40 85 Supply voltage Operating free-air temperature range UNIT V C 7.4 Thermal Information LM833 THERMAL METRIC (1) D DGK P UNIT 85 C/W 8 PINS RJA (1) (2) (3) 4 Junction-to-ambient thermal resistance (2) (3) 97 172 For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report (SPRA953). Maximum power dissipation is a function of TJ(max), JA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) - TA) / JA. Operating at the absolute maximum TJ of 150C can affect reliability. The package thermal impedance is calculated in accordance with JESD 51-7. Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 LM833 www.ti.com SLOS481B - JULY 2010 - REVISED OCTOBER 2014 7.5 Electrical Characteristics VCC- = -15 V, VCC+ = 15 V, TA = 25C (unless otherwise noted) PARAMETER TEST CONDITIONS VIO Input offset voltage VO = 0, RS = 10 , VCM = 0 VIO Input offset voltage temperature coefficient VO = 0, RS = 10 , VCM = 0 IIB Input bias current VO = 0, VCM = 0 IIO Input offset current VO = 0, VCM = 0 VICR Common-mode input voltage range VIO = 5 mV, VO = 0 AVD Large-signal differential voltage amplification RL 2 k, VO = 10 V Maximum output voltage swing TYP MAX 0.15 2 TA = -40C to 85C TA = -40C to 85C mV V/C 2 300 750 nA 800 TA = 25C 25 150 TA = -40C to 85C RL = 10,000 UNIT 3 TA = -40C to 85C RL = 2000 VID = 1 V TA = 25C TA = 25C RL = 600 VOM MIN nA 175 13 14 TA = 25C 90 110 TA = -40C to 85C 85 VOM+ 10.7 VOM- -11.9 VOM+ 13.2 13.8 VOM- -13.2 -13.7 VOM+ 13.5 14.1 VOM- V dB V -14 -14.6 CMMR Common-mode rejection ratio VIN = 13 V 80 100 dB kSVR (1) Supply-voltage rejection ratio VCC+ = 5 V to 15 V, VCC- = -5 V to -15 V 80 105 dB 15 29 -20 -37 IOS Output short-circuit current |VID| = 1 V, Output to GND ICC Supply current (per channel) VO = 0 (1) Source current Sink current TA = 25C mA 2.05 2.5 TA = -40C to 85C mA 2.75 Measured with VCC differentially varied at the same time 7.6 Operating Characteristics VCC- = -15 V, VCC+ = 15 V, TA = 25C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN SR Slew rate at unity gain AVD = 1, VIN = -10 V to 10 V, RL = 2 k, CL = 100 pF GBW Gain bandwidth product f = 100 kHz B1 Unity gain frequency Open loop CL = 0 pF TYP MAX UNIT 5 7 V/s 10 16 MHz 9 MHz -11 Gm Gain margin RL = 2 k m Phase margin RL = 2 k Amp-to-amp isolation f = 20 Hz to 20 kHz Power bandwidth VO = 27 V(PP), RL = 2 k, THD 1% THD Total harmonic distortion VO = 3 Vrms, AVD = 1, RL = 2 k, f = 20 Hz to 20 kHz zo Open-loop output impedance VO = 0, f = 9 MHz rid Differential input resistance Cid Differential input capacitance Vn In CL = 100 pF -6 CL = 0 pF 55 CL = 100 pF 40 dB degrees -120 dB 120 kHz 0.002% 37 VCM = 0 175 k VCM = 0 12 pF Equivalent input noise voltage f = 1 kHz, RS = 100 4.5 nV/Hz Equivalent input noise current f = 1 kHz 0.5 pA/Hz Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 5 LM833 SLOS481B - JULY 2010 - REVISED OCTOBER 2014 www.ti.com 7.7 Typical Characteristics 0.1 F 100 k 10 2.0 k 4.3 k + D.U.T. 22 F 1/2 LM833 Scope x1 RIN = 1.0 M - 4.7 F 100 k Voltage Gain = 50,000 2.2 F 24.3 k 110 k 0.1 F NOTE: All capacitors are non-polarized. Figure 1. Voltage Noise Test Circuit (0.1 Hz to 10 Hz) 600 600 VCM = 0 V VCC+ = 15 V VCC- = -15 V TA = 25C 400 300 200 100 0 -15 6 TA = 25C 500 IIB - Input Bias Current - nA IIB - Input Bias Current - nA 500 400 300 200 100 0 -10 -5 0 5 10 5 15 6 7 8 9 10 11 12 13 14 15 16 17 18 VCM - Common Mode Voltage - V VCC+/-VCC- - Supply Voltage - V Figure 2. Input Bias Current vs Common-Mode Voltage Figure 3. Input Bias Current vs Supply Voltage Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 LM833 www.ti.com SLOS481B - JULY 2010 - REVISED OCTOBER 2014 Typical Characteristics (continued) 1000 2 VCC- = -15 V 800 VCM = 0 V VCC+ = 15 V VCC- = -15 V 1.5 VIO - Input Offset Voltage - mV IIB - Input Bias Current - nA VCC+ = 15 V 900 700 600 500 400 300 200 VCM = 0 V 1 0.5 0 -0.5 -1 -1.5 100 0 -55 -35 -15 5 25 45 65 85 -2 -55 -35 -15 105 125 5 25 45 65 85 105 125 TA - Temperature - C TA - Temperature - C Figure 4. Input Bias Current vs Temperature Figure 5. Input Offset Voltage vs Temperature 1.4 0 1.2 -0.2 VCC- = -3 V to -15 V D VIO = 5 mV -0.4 VO = 0 V Input Common-Mode Voltage High Proximity to V CC+ - V Input Common-Mode Voltage Low Proximity to V CC- - V VCC+ = 3 V to 15 V 1 0.8 0.6 VCC+ = 3 V to 15 V 0.4 VCC- = -3 V to -15 V D e VIO = 5 mV 0.2 VO = 0 V 0 -55 -25 5 35 65 95 -0.6 -0.8 -1 -1.2 -1.4 -55 125 -25 TA - Temperature - C Figure 6. Input Common-Mode Voltage Low Proximity to VCC- vs Temperature 35 65 95 125 Figure 7. Input Common-Mode Voltage High Proximity to VCC+ vs Temperature 10 0 -1 9 TA = 125C -2 8 TA = 25C -3 Output Saturation Voltage Proximity to V CC- - V Output Saturation Voltage Proximity to V CC+ - V 5 TA - Temperature - C TA = -55C -4 -5 -6 -7 -8 7 6 5 TA = 125C 4 TA = 25C 3 TA = -55C 2 -9 1 -10 0 0.5 1 1.5 2 2.5 3 3.5 4 0 4.5 0 kW RL - Load Resistance - kh 0.5 1 1.5 2 2.5 3 3.5 4 4.5 kW RL - Load Resistance - k@ Figure 8. Output Saturation Voltage Proximity to VCC+ vs Load Resistance Figure 9. Output Saturation Voltage Proximity to VCC- vs Load Resistance Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 7 LM833 SLOS481B - JULY 2010 - REVISED OCTOBER 2014 www.ti.com Typical Characteristics (continued) 10 70 9 VCC- = -15 V 60 VID = 1 V 8 ICC - Supply Current - mA IOS - Output Short-Circuit Current - mA VCC+ = 15 V 50 40 Source Sink 30 VCM = 0 V RL = High Impedance VO = 0 V 7 6 VCC = 15 V 5 4 VCC = 10 V 3 VCC = 5 V 2 20 1 10 -55 -35 -15 5 25 45 65 85 0 -55 105 125 -35 -15 TA - Temperature - C Figure 10. Output Short-Circuit Current vs Temperature 100 80 45 65 85 105 125 120 VCC+ = 15 V VCC- = -15 V TA = 25C 110 100 90 80 60 PSRR - dB CMMR - dB 70 25 Figure 11. Supply Current vs Temperature VCC+ = 15 V VCC- = -15 V VCM = 0 V DVCM = 1.5 V TA = 25C 90 5 TA - Temperature - C 50 40 70 T3P 60 50 T3N 40 30 30 20 20 10 10 0 100 10k 100k 1.0E+06 10M 1k 1M 1.0E+02 1.0E+03 1.0E+04 1.0E+05 1.0E+07 0 1.0E+02 1.0E+03 1.0E+04 1.0E+05 1.0E+07 100 10k 100k 1.0E+06 10M 1k 1M f - Frequency - Hz f - Frequency - Hz Figure 12. CMRR vs Frequency Figure 13. PSSR vs Frequency 30 GBW - Gain Bandwidth Product - MHz GBW - Gaind Bandwidth Product - MHz 30 25 20 15 10 5 0 5 6 7 8 20 15 10 5 0 -55 9 10 11 12 13 14 15 16 17 18 VCC+/-VCC- - Supply Voltage - V -35 -15 5 25 45 65 85 105 125 TA - Temperature - C Figure 14. Gain Bandwidth Product vs Supply Voltage 8 25 Figure 15. Gain Bandwidth Product vs Temperature Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 LM833 www.ti.com SLOS481B - JULY 2010 - REVISED OCTOBER 2014 Typical Characteristics (continued) 20 30 VCC+ = 15 V VCC- = -15 V RL = 2 kW AV = 1 THD < 1% TA = 25C 15 25 VO - Output Voltage - V VO - Output Voltage - V RL = 10 kW 10 RL = 2 kW 5 0 -5 RL = 10 kW -10 20 15 10 RL = 2 kW 5 -15 -20 5 6 7 8 0 100 10 10k 100k 1.E+06 10M 1k 1M 1.E+01 1.E+02 1.E+03 1.E+04 1.E+05 1.E+07 9 10 11 12 13 14 15 16 17 18 VCC+/-VCC- - Supply Voltage - V f - Frequency - Hz Figure 16. Output Voltage vs Supply Voltage Figure 17. Output Voltage vs Frequency 120 110 115 AV - Open-Loop Gain - dB AV - Open-Loop Gain - dB 105 100 95 90 RL = 2 kW f < 10 Hz DVO = 2/3(VCC+ - VCC-) TA = 25C 85 6 7 8 105 100 95 90 85 80 5 110 RL = 2 kW f < 10 Hz DVO = 2/3(VCC+ - VCC-) TA = 25C 80 -55 9 10 11 12 13 14 15 16 17 18 -35 -15 5 25 45 65 85 105 125 VCC+/-VCC- - Supply Voltage - V TA - Temperature - C Figure 18. Open-Loop Gain vs Supply Voltage Figure 19. Open-Loop Gain vs Temperature 200 50 VCC+ = 15 V 40 35 VCC- = -15 V 190 VO = 1 Vrms 180 TA = 25C Crosstalk Rejection - dB ZO - Output Impedance - W 45 30 25 20 15 AV = 1000 10 AV = 100 AV = 10 160 150 140 130 120 AV = 1 5 0 1.0E+03 1k 170 Drive Channel VCC+ = 15 V VCC- = -15 V RL = 2 kW VO = 20 VPP TA = 25C 110 1.0E+04 10k 1.0E+05 100k 1.0E+06 1M 100 1.E+01 10 1.0E+07 10M f - Frequency - Hz 1.E+02 100 1.E+03 1k 1.E+04 10k 1.E+05 100k f - Frequency - Hz Figure 20. Output Impedance vs Frequency Figure 21. Crosstalk Rejection vs Frequency Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 9 LM833 SLOS481B - JULY 2010 - REVISED OCTOBER 2014 www.ti.com Typical Characteristics (continued) AV = 1000 0.01 0.001 0.1 AV = 100 0.01 AV = 10 0.001 VCC+ = 15 V VCC- = -15 V f = 2 kHz RL = 2 kW TA = 25C AV = 1 0.0001 0.0001 10 1.E+01 100 1.E+02 1k 1.E+03 10k 1.E+04 0 100k 1.E+05 1 2 f - Frequency - Hz Figure 22. Total Harmonic Distortion vs Frequency 10 9 9 7 Rising Edge 6 5 4 DV = 2/3(V - V ) IN CC+ CC- AV = 1 3 RL = 2 kW TA = 25C 2 5 6 7 8 9 10 11 12 13 14 15 16 17 18 SR - Slew Rate - V/s SR - Slew Rate - V/s 8 Falling Edge VCC+ = 15 V VCC- = -15 V DVIN = 20 V AV = 1 RL = 2 kW 4 5 1.E+04 10k Gain Margin - dB -90 Gain, TA = 125C 45 65 85 VCC+ = 15 V VCC- = -15 V VO = 0 V 1.E+06 1M 125 10 40 6 Phase, TA = 125C 50 60 Phase, TA = 25C 70 0 -180 1.E+07 10M 0 30 Phase, TA = -55C 1.E+05 100k 105 20 Gain, TA = -55C 3 -135 VCC+ = 15 V VCC- = -15 V RL = 2 kW TA = 25C 25 9 -45 Gain 0 1.E+03 1k 1 10 100 80 1000 Cout - Output Load Capacitance - pF f - Frequency - Hz Figure 26. Gain and Phase vs Frequency 10 -15 Figure 25. Slew Rate vs Temperature 12 Phase Shift - deg Gain - dB 10 -35 TA - Temperature - C 30 20 9 5 Gain, TA = 25C 40 8 Rising Edge 70 50 7 6 2 -55 0 60 6 7 3 Figure 24. Slew Rate vs Supply Voltage Phase 5 Falling Edge VCC+/-VCC- - Supply Voltage - V 80 4 Figure 23. Total Harmonic Distortion vs Output Voltage 10 8 3 VO - Output Voltage - Vrms Phase Margin - deg 0.1 1 VCC+ = 15 V VCC- = -15 V VO = 1 Vrms AV = 1 RL = 2 kW TA = 25C THD - Total Harmonic Distortion - % THD - Total Harmonic Distortion - % 1 Submit Documentation Feedback Figure 27. Gain and Phase Margin vs Output Load Capacitance Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 LM833 www.ti.com SLOS481B - JULY 2010 - REVISED OCTOBER 2014 Typical Characteristics (continued) 80 VCC+ = 15 V VCC- = -15 V VCC- = -15 V VIN = 100 mVPP TA = 25C Overshoot - % 70 60 50 40 TA = 125C 30 20 10 VCC+ = 15 V nV/OHz Input Voltage Noise - nV/rtHz 90 TA = 25C 10 pA/OHz Input Current Noise - pA/rtHz 100 100 1 Input Voltage Noise Input Current Noise 10 TA = -55C 1 10 100 1000 10 100 Cout - Output Load Capacitance - pF 1k 1000 10k 10000 0.1 100k 100000 f - Frequency - Hz Figure 28. Overshoot vs Output Load Capacitance Figure 29. Input Voltage and Current Noise vs Frequency 16 1000 64 60 VCC- = -15 V f = 1 Hz TA = 25C 14 56 52 12 48 Phase Margin 100 Gain Margin - dB nV/OHz Input Referred Noise Voltage - nV/rtHz VCC+ = 15 V 10 44 10 40 Gain Margin 36 8 32 28 6 4 2 VCC+ = 15 V 24 VCC- = -15 V 20 AV = 100 16 VO = 0 V 12 TA = 25C 8 Phase Margin - deg 0 4 0 1.E+02 100 1.E+03 1k 1.E+04 10k 1.E+05 100k 1.E+06 1M 1 00 Figure 30. Input Referred Noise Voltage vs Source Resistance 55 45 0 45 -10 35 VCC+ = 15 V VCC- = -15 V AV = 1 RL = 2 kW CL = 100 pF TA = 25C -20 -30 5 -40 -5 -15 -2 2 6 10 14 18 VO - Output Voltage - V 10 VI - Input Voltage - V VO - Output Voltage - V Input Output 101k 00 0 1010k 0 0 0 10100k 0000 Figure 31. Gain and Phase Margin vs Differential Source Resistance 55 15 100 10 0 RSD - Differential Source Resistance - W e RS - Source Resistance - W e 25 10 10 Input 10 0 35 25 15 -10 VCC+ = 15 V VCC- = -15 V AV = -1 RL = 2 kW CL = 100 pF TA = 25C Output -20 -30 5 -40 -50 -5 -50 -60 -15 22 -60 -2 Time - s VI - Input Voltage - V 1 1.E+01 10 2 6 10 14 18 22 Time - s Figure 32. Large Signal Transient Response (AV = 1) Figure 33. Large Signal Transient Response (AV = -1) Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 11 LM833 SLOS481B - JULY 2010 - REVISED OCTOBER 2014 www.ti.com Typical Characteristics (continued) 0.6 0.2 400 0.5 0.1 300 -0.1 0.3 VCC+ = 15 V VCC- = -15 V AV = 1 RL = 2 kW CL = 100 pF TA = 25C 0.2 0.1 -0.2 -0.3 -0.4 0 Input Voltage Noise - nV Input VI - Input Voltage - V VO - Output Voltage - V 200 0.0 0.4 Output -0.2 -0.5 0.5 1.0 -200 T3 VCC+ = 15 V -300 VCC- = -15 V BW = 0.1 Hz to 10 Hz TA = 25C -5 1.5 -4 -3 -2 -1 0 1 2 3 4 5 Time - s Time - s Figure 34. Small Signal Transient Response 12 -100 -500 -0.6 0.0 0 -400 -0.5 -0.1 100 Submit Documentation Feedback Figure 35. Low-Frequency Noise Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 LM833 www.ti.com SLOS481B - JULY 2010 - REVISED OCTOBER 2014 8 Detailed Description 8.1 Overview The LM833 device is a dual operational amplifier with high-performance specifications for use in quality audio and data-signal applications. This device operates over a wide range of single- and dual-supply voltage with low noise, high-gain bandwidth, and high slew rate. Additional features include low total harmonic distortion, excellent phase and gain margins, large output voltage swing with no deadband crossover distortions, and symmetrical sink/source performance. The dual amplifiers are utilized widely in circuit of audio optimized for all preamp and high-level stages in PCM and HiFi systems. The LM833 device is pin-for-pin compatible with industry-standard dual operation amplifiers' pin assignments. With addition of a preamplifier, the gain of the power stage can be greatly reduced to improve performance. 8.2 Functional Block Diagram VCC INi IN+ VOUT VEE Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 13 LM833 SLOS481B - JULY 2010 - REVISED OCTOBER 2014 www.ti.com 8.3 Feature Description 8.3.1 Operating Voltage The LM833 operational amplifier is fully specified and ensured for operation from 5 V to 18 V. In addition, many specifications apply from -40C to 85C. Parameters that vary significantly with operating voltages or temperature are shown in Absolute Maximum Ratings . 8.3.2 High Gain Bandwidth Product Gain bandwidth product is found by multiplying the measured bandwidth of an amplifier by the gain at which that bandwidth was measured. The LM833 has a high gain bandwidth of 16 MHz which stays relatively stable over a wide range of supply voltages. Parameters that vary significantly with temperature are shown in Figure 14. 8.3.3 Low Total Harmonic Distortion Harmonic distortions to an audio signal are created by electronic components in a circuit. Total harmonic distortion (THD) is a measure of harmonic distortions accumulated by a signal in an audio system. The LM833 has a very low THD of 0.002% meaning that the LM833 will add little harmonic distortion when used in audio signal applications. More specific characteristics are shown in Figure 22. 8.4 Device Functional Modes The LM833 is powered on when the supply is connected. It can be operated as a single supply operational amplifier or dual supply amplifier depending on the application. 14 Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 LM833 www.ti.com SLOS481B - JULY 2010 - REVISED OCTOBER 2014 9 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 9.1 Application Information An application of the LM833 is the two stage RIAA Phono Preamplifier. A primary task of the phono preamplifier is to provide gain (usually 30 to 40 dB at 1 kHz) and accurate amplitude and phase equalization to the signal from a moving magnet or a moving coil cartridge. In addition to the amplification and equalization functions, the phono preamp must not add significant noise or distortion to the signal from the cartridge. The circuit shown in Figure 36 uses two amplifiers, fulfills these qualifications, and has greatly improved performance over a singleamplifier design. 9.2 Typical Application VIN 47 k CP 1/2 LM833 3 + 2 1 C4 2 PF R3 2.37 4 C3 33 nF -15 V R1 80.6 k 15 V R6 54.9 k R2 8.45 k R4 2k R0 499 5 + 8 6 7 VOUT 1/2 LM833 R5 4.3 k C1 39 nF C0 200 PF Figure 36. RIAA Phono Preamplifier 9.2.1 Design Requirements * Supply Voltage = 15 V * Low-Frequency -3 dB corner of the first amplifier (f0) > 20 Hz (below audible range) * Low-Frequency -3 dB corner of the second stage (fL) = 20.2 Hz 9.2.2 Detailed Design Procedure 9.2.2.1 Introduction to Design Method Equation 1 through Equation 5 show the design equations for the preamplifier. R1 = 8.058 R0A1 where * A1 is the 1 kHz voltage gain of the first amplifier (1) Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 15 LM833 SLOS481B - JULY 2010 - REVISED OCTOBER 2014 www.ti.com Typical Application (continued) C1 = 3.18 10-3 R1 (2) R R 2 = 1 - R0 9 C3 = 7.5 10-5 (3) (R3 + R6 ) 7.5 10 = R3 R 6 RP -5 (4) 1 C4 = 2 p f L (R3 + R6 ) where fL is the low-frequency -3 dB corner of the second stage * (5) For standard RIAA preamplifiers, fL should be kept well below the audible frequency range. If the preamplifier is to follow the IEC recommendation (IEC Publication 98, Amendment #4), fL should equal 20.2 Hz. R A V2 = 1 + 5 R4 where * AV2 is the voltage gain of the second amplifier (6) 1 2 p f0 R0 C0 where * f0 is the low-frequency -3 dB corner of the first amplifier (7) This should be kept well below the audible frequency range. A design procedure is shown below with an illustrative example using 1% tolerance E96 components for close conformance to the ideal RIAA curve. Because 1% tolerance capacitors are often difficult to find except in 5% or 10% standard values, the design procedure calls for re-calculation of a few component values so that standard capacitor values can be used. 9.2.2.2 RIAA Phono Preamplifier Design Procedure A design procedure is shown below with an illustrative example using 1% tolerance E96 components for close conformance to the ideal RIAA curve. Since 1% tolerance capacitors are often difficult to find except in 5% or 10% standard values, the design procedure calls for re-calculation of a few component values so that standard capacitor values can be used. Choose R0. R0 should be small for minimum noise contribution, but not so small that the feedback network excessively loads the amplifier. Example: Choose R0 = 500 Choose 1 kHz gain, AV1 of first amplifier. This will typically be around 20 dB to 30 dB. Example: Choose AV1 = 26 dB = 20 Calculate R1 = 8.058 R0AV1 Example: R1 = 8.058 x 500 x 20 = 80.58 k Calculate C1 = Example : C1 = 3.18 10-3 R1 3.18 10-3 8.058 104 (8) = 0.03946 mF (9) If C1 is not a convenient value, choose the nearest convenient value and calculate a new R1 from Equation 10. 16 Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 LM833 www.ti.com SLOS481B - JULY 2010 - REVISED OCTOBER 2014 Typical Application (continued) R1 = 3.18 10-3 C1 (10) Example: New C1 = 0.039 F. New R1 = 3.18 10-3 3.9 10-8 = 81.54k Use R1 = 80.6k (11) Calculate a new value for R0 from Equation 12. R1 R0 = 8.058 A V1 (12) 4 Example: New R0 = 8.06 10 = 498.8 8.058 20 (13) Use R0 = 499. Calculate R2 = R1 - R0 9 8.06 104 - 499 = 8456.56 9 Example : R2 = (14) Use R2 = 8.45 K. Choose a convenient value for C3 in the range from 0.01 F to 0.05 F. Example: C3 = 0.033 F Calculate RP = Example: RP = 7.5 10-5 C3 7.5 10-5 3.3 10-8 = 2.273k (15) Choose a standard value for R3 that is slightly larger than RP. Example: R3 = 2.37 k Calculate R6 from 1 / R6 = 1 / RP - 1 / R3 Example: R6 = 55.36 k Use 54.9 k Calculate C4 for low-frequency rolloff below 1 Hz from design Equation 5. Example: C4 = 2 F. Use a good quality mylar, polystyrene, or polypropylene. Choose gain of second amplifier. Example: The 1 kHz gain up to the input of the second amplifier is about 26 dB for this example. For an overall 1 kHz gain equal to about 36 dB we choose: AV2 = 10 dB = 3.16 Choose value for R4. Example: R4 = 2 k Calculate R5 = (AV2 - 1) R4 Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 17 LM833 SLOS481B - JULY 2010 - REVISED OCTOBER 2014 www.ti.com Typical Application (continued) Example: R5 = 4.32 k Use R5 = 4.3 k Calculate C0 for low-frequency rolloff below 1 Hz from design Equation 7. Example: C0 = 200 F 9.2.3 Application Curves for Output Characteristics The maximum observed error for the prototype was 0.1 dB. Figure 37. Deviation from Ideal RIAA Response for Circuit of Figure 36 Using 1% Resistors The lower curve is for an output level of 300 mVrms and the upper curve is for an output level of 1 Vrms. Figure 38. THD of Circuit in Figure 36 as a Function of Frequency 9.3 Typical Application -- Reducing Oscillation from High-Capacitive Loads While all the previously stated operating characteristics are specified with 100-pF load capacitance, the LM833 device can drive higher-capacitance loads. However, as the load capacitance increases, the resulting response pole occurs at lower frequencies, causing ringing, peaking, or oscillation. The value of the load capacitance at which oscillation occurs varies from lot-to-lot. If an application appears to be sensitive to oscillation due to load capacitance, adding a small resistance in series with the load should alleviate the problem (see Figure 39). 9.3.1 Test Schematic 15 V RO VO 5V -5 V -15 V CL RL = 2 k Figure 39. Capacitive Load Testing Circuit 18 Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 LM833 www.ti.com SLOS481B - JULY 2010 - REVISED OCTOBER 2014 Typical Application -- Reducing Oscillation from High-Capacitive Loads (continued) 9.3.2 Output Characteristics Figure 40 through Figure 45 demonstrate the effect adding this small resistance has on the ringing in the output signal. Maximum capacitance before oscillation = 590 pF 0.25 V per Division 0.25 V per Division Maximum capacitance before oscillation = 380 pF 250 ns per Division 250 ns per Division Figure 40. Pulse Response (RL = 600 , CL = 380 pF) Figure 41. Pulse Response (RL = 2 k, CL = 560 pF) 0.25 V per Division 0.25 V per Division Maximum capacitance before oscillation = 590 pF 250 ns per Division 250 ns per Division Figure 42. Pulse Response (RL = 10 k, CL = 590 pF) 0.25 V per Division 0.25 V per Division Figure 43. Pulse Response (RO = 0 , CO = 1000 pF, RL = 2 k) 250 ns per Division 250 ns per Division Figure 44. Pulse Response (RO = 4 , CO = 1000 pF, RL = 2 k) Figure 45. Pulse Response (RO = 35 , CO = 1000 pF, RL = 2 k) Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 19 LM833 SLOS481B - JULY 2010 - REVISED OCTOBER 2014 www.ti.com 10 Power Supply Recommendations The LM833 is specified for operation from 10 to 36 V (5 to 18 V); many specifications apply from -40C to 85C. The Typical Characteristics section presents parameters that can exhibit significant variance with regard to operating voltage or temperature. CAUTION Supply voltages larger than 36 V can permanently damage the device (see Absolute Maximum Ratings ). Place 0.1-F bypass capacitors close to the power-supply pins to reduce errors coupling in from noisy or high impedance power supplies. For more detailed information on bypass capacitor placement, refer to the Layout section. 11 Layout 11.1 Layout Guidelines For best operational performance of the device, use good PCB layout practices, including: * Noise can propagate into analog circuitry through the power pins of the circuit as a whole and the operational amplifier. Bypass capacitors are used to reduce the coupled noise by providing low impedance power sources local to the analog circuitry. - Connect low-ESR, 0.1-F ceramic bypass capacitors between each supply pin and ground, placed as close to the device as possible. A single bypass capacitor from V+ to ground is applicable for single supply applications. * Separate grounding for analog and digital portions of circuitry is one of the simplest and most-effective methods of noise suppression. One or more layers on multilayer PCBs are usually devoted to ground planes. A ground plane helps distribute heat and reduces EMI noise pickup. Make sure to physically separate digital and analog grounds, paying attention to the flow of the ground current. For more detailed information, refer to Circuit Board Layout Techniques, (SLOA089). * To reduce parasitic coupling, run the input traces as far away from the supply or output traces as possible. If it is not possible to keep them separate, it is much better to cross the sensitive trace perpendicular as opposed to in parallel with the noisy trace. * Place the external components as close to the device as possible. Keeping RF and RG close to the inverting input minimizes parasitic capacitance, as shown in Layout Example. * Keep the length of input traces as short as possible. Always remember that the input traces are the most sensitive part of the circuit. * Consider a driven, low-impedance guard ring around the critical traces. A guard ring can significantly reduce leakage currents from nearby traces that are at different potentials. 11.2 Layout Example VIN RIN RG + VOUT RF Figure 46. Operational Amplifier Schematic for Noninverting Configuration 20 Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 LM833 www.ti.com SLOS481B - JULY 2010 - REVISED OCTOBER 2014 Layout Example (continued) Place components close to device and to each other to reduce parasitic errors Run the input traces as far away from the supply lines as possible VS+ RF OUT1 VCC+ GND IN1i OUT2 VIN IN1+ IN2i VCCi IN2+ RG GND RIN Use low-ESR, ceramic bypass capacitor Only needed for dual-supply operation GND VS(or GND for single supply) Ground (GND) plane on another layer Figure 47. Operational Amplifier Board Layout for Noninverting Configuration Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 21 LM833 SLOS481B - JULY 2010 - REVISED OCTOBER 2014 www.ti.com 12 Device and Documentation Support 12.1 Trademarks All trademarks are the property of their respective owners. 12.2 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 12.3 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 22 Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 LM833 www.ti.com SLOS481B - JULY 2010 - REVISED OCTOBER 2014 13 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Submit Documentation Feedback Copyright (c) 2010-2014, Texas Instruments Incorporated Product Folder Links: LM833 23 PACKAGE OPTION ADDENDUM www.ti.com 24-Aug-2018 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM833D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 LM833 LM833DGKR ACTIVE VSSOP DGK 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 RSU LM833DGKT ACTIVE VSSOP DGK 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 RSU LM833DR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 LM833 LM833P ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type -40 to 85 LM833P (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 24-Aug-2018 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 3-Aug-2017 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing LM833DGKR VSSOP DGK 8 LM833DGKT VSSOP DGK LM833DR SOIC D LM833DR SOIC D SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 2500 330.0 12.4 5.3 3.3 1.3 8.0 12.0 Q1 8 250 180.0 12.4 5.3 3.3 1.3 8.0 12.0 Q1 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 3-Aug-2017 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM833DGKR VSSOP DGK 8 2500 346.0 346.0 35.0 LM833DGKT VSSOP DGK 8 250 203.0 203.0 35.0 LM833DR SOIC D 8 2500 367.0 367.0 35.0 LM833DR SOIC D 8 2500 340.5 338.1 20.6 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2018, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM833D LM833DGKR LM833DGKT LM833DR LM833P LM833MMX