LMH6640 LMH6640 TFT-LCD Single, 16V Rail-to-Rail High Output Operational Amplifier Literature Number: SNOSAA0A LMH6640 TFT-LCD Single, 16V Rail-to-Rail High Output Operational Amplifier General Description Features The LMHTM6640 is a voltage feedback operational amplifier (VS = 16V, RL= 2 k to V+/2, 25C, Typical Values Unless Specified) n Supply current (no load) 4 mA n Output resistance (closed loop 1 MHz) 0.35 n -3 dB BW (AV = 1) 190 MHz n Settling time ( 0.1%, 2 VPP) 35 ns n Input common mode voltage -0.3V to 15.1V n Output voltage swing 100 mV from rails 100 mA n Linear output current n Total harmonic distortion (2 VPP, 5 MHz) -64 dBc n Fully characterized for: 5V & 16V n No output phase reversal with CMVR exceeded n Differential gain (RL = 150) 0.12% n Differential phase (RL = 150) 0.12 with a rail-to-rail output drive capability of 100 mA. Employing National's patented VIP10 process, the LMH6640 delivers a bandwidth of 190 MHz at a current consumption of only 4mA. An input common mode voltage range extending to 0.3V below the V- and to within 0.9V of V+, makes the LMH6640 a true single supply op-amp. The output voltage range extends to within 100 mV of either supply rail providing the user with a dynamic range that is especially desirable in low voltage applications. The LMH6640 offers a slew rate of 170 V/s resulting in a full power bandwidth of approximately 28 MHz with 5V single supply (2 VPP, -1 dB). Careful attention has been paid to ensure device stability under all operating voltages and modes. The result is a very well behaved frequency response characteristic for any gain setting including +1, and excellent specifications for driving video cables including total harmonic distortion of -64 dBc @ 5 MHz, differential gain of 0.12% and differential phase of 0.12. Applications n n n n n n TFT panel VCOM buffer amplifier Active filters CD/DVD ROM ADC buffer amplifier Portable video Current sense buffer Typical Application 20086234 Typical Application as a TFT Panel VCOM Driver LMHTM is a trademark of National Semiconductor Corporation. (c) 2004 National Semiconductor Corporation DS200862 www.national.com LMH6640 TFT-LCD Single, 16V Rail-to-Rail High Output Operational Amplifier November 2004 LMH6640 Absolute Maximum Ratings (Note 1) Junction Temperature (Note 4) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Soldering Information +150C Infrared or Convection (20 sec.) 235C Wave Soldering (10 sec.) 260C ESD Tolerance (Note 2) Human Body Model 2 KV Machine Model 200V Operating Ratings (Note 3) Supply Voltage (V+ - V-) 2.5V VIN Differential 10 mA Input Current Supply Voltages (V+ - V-) 18V + V +0.8V, V -0.8V Storage Temperature Range -65C to +150C -40C to +85C Package Thermal Resistance (Note 4) - Voltage at Input/Output Pins 4.5V to 16V Operating Temperature Range (Note 4) 5-Pin SOT23 265C/W 5V Electrical Characteristics Unless otherwise specified, All limits guaranteed for TJ = 25C, V+ = 5V, V- = 0V, VO = VCM = V+/2 and RL = 2 k to V+/2. Boldface limits apply at temperature extremes. (Note 9) Symbol BW BW0.1 dB Parameter Conditions Min (Note 6) Typ (Note 5) AV = +1 (RL = 100) 150 AV = -1 (RL = 100) 58 0.1 dB Gain Flatness AV = -3 18 -3 dB Bandwidth Max (Note 6) Units MHz MHz FPBW Full Power Bandwidth AV = +1, VOUT = 2 VPP, -1 dB 28 MHz LSBW -3 dB Bandwidth AV = +1, VO = 2 VPP (RL = 100) 32 MHz GBW Gain Bandwidth Product AV = +1, (RL = 100) 59 MHz SR Slew Rate (Note 8) AV = -1 en Input Referred Voltage Noise in Input Referred Current Noise 170 V/s f = 10 kHz 23 nV/ f = 1 MHz 15 f = 10 kHz 1.1 f = 1 MHz 0.7 THD Total Harmonic Distortion f = 5 MHz, VO = 2 VPP, AV = +2 RL = 1 k to V+/2 -65 ts Settling Time VO = 2 VPP, 0.1%, AV = -1 35 VOS Input Offset Voltage IB Input Bias Current (Note 7) IOS Input Offset Current CMVR Common Mode Input Voltage Range CMRR 50 dB 4.0 3.6 mV -1.2 -2.6 -3.25 A 34 800 1400 nA -0.3 -0.2 -0.1 4.1 V- VCM V+ -1.5V 72 90 AVOL Large Signal Voltage Gain VO = 4 VPP, RL = 2 k to V+/2 86 82 95 VO = 3.75 VPP, RL = 150 to V+/2 74 70 78 RL = 2 k to V+/2 4.90 4.94 RL = 150 to V+/2 4.75 4.80 Output Swing Low www.national.com + ns 5 7 Common Mode Rejection Ratio Output Swing High dBc 1 CMRR VO pA/ dB dB RL = 2 k to V /2 0.06 0.10 RL = 150 to V+/2 0.20 0.25 2 V V LMH6640 5V Electrical Characteristics (Continued) Unless otherwise specified, All limits guaranteed for TJ = 25C, V+ = 5V, V- = 0V, VO = VCM = V+/2 and RL = 2 k to V+/2. Boldface limits apply at temperature extremes. (Note 9) Symbol ISC IOUT Parameter Output Short Circuit Current (Note 3) Conditions Min (Note 6) Typ (Note 5) Sourcing to V+/2 100 75 130 Sinking from V+/2 100 70 130 Output Current VO = 0.5V from either Supply Max (Note 6) mA +75/-90 PSRR Power Supply Rejection Ratio 4V V 6V IS Supply Current No Load 3.7 RIN Common Mode Input Resistance AV = +1, f = 1 kHz, RS = 1 M 15 CIN Common Mode Input Capacitance AV = +1, RS = 100 k 1.7 ROUT Output Resistance Closed Loop RF = 10 k, f = 1 kHz, AV = -1 + 72 Units mA 80 dB 5.5 8.0 mA M pF 0.1 RF = 10 k, f = 1 MHz, AV = -1 0.4 DG Differential Gain NTSC, AV = +2 RL = 150 to V+/2 0.13 DP Differential Phase NTSC, AV = +2 RL = 150 to V+/2 0.10 % deg 16V Electrical Characteristics Unless otherwise specified, All limits guaranteed for TJ = 25C, V+ = 16V, V- = 0V, VO = VCM = V+/2 and RL = 2 k to V+/2. Boldface limits apply at temperature extremes. (Note 9) Symbol BW Parameter -3 dB Bandwidth BW0.1 dB 0.1 dB Gain Flatness Conditions Min (Note 6) Typ (Note 5) Max (Note 6) Units AV = +1 (RL = 100) 190 AV = -1 (RL = 100) 60 AV = -2.7 20 MHz MHz LSBW -3 dB Bandwidth AV = +1, VO = 2 VPP (RL = 100) 35 MHz GBW Gain Bandwidth Product AV = +1, (RL = 100) 62 MHz SR Slew Rate (Note 8) AV = -1 170 V/s en Input Referred Voltage Noise in Input Referred Current Noise f = 10 kHz 23 f = 1 MHz 15 f = 10 kHz 1.1 f = 1 MHz 0.7 THD Total Harmonic Distortion f = 5 MHz, VO = 2 VPP, AV = +2 RL = 1 k to V+/2 -64 VO = 2 VPP, 0.1%, AV = -1 35 nV/ pA/ dBc ts Settling Time VOS Input Offset Voltage 1 5 7 mV IB Input Bias Current (Note 7) -1 -2.6 -3.5 A IOS Input Offset Current 34 800 1800 nA CMVR Common Mode Input Voltage Range -0.3 -0.2 -0.1 CMRR Common Mode Rejection Ratio CMRR 50 dB V- VCM V+ -1.5V 3 15.0 14.6 15.1 72 90 ns V dB www.national.com LMH6640 16V Electrical Characteristics (Continued) Unless otherwise specified, All limits guaranteed for TJ = 25C, V+ = 16V, V- = 0V, VO = VCM = V+/2 and RL = 2 k to V+/2. Boldface limits apply at temperature extremes. (Note 9) Symbol AVOL VO Parameter Large Signal Voltage Gain Output Swing High Conditions Min (Note 6) Typ (Note 5) VO = 15 VPP, RL = 2 k to V+/2 86 82 95 VO = 14 VPP, RL = 150 to V+/2 74 70 78 15.85 15.90 15.45 15.78 RL = 2 k to V+/2 + RL = 150 to V /2 Output Swing Low ISC Output Short Circuit Current (Note 3) Max (Note 6) dB RL = 2 k to V+/2 0.10 0.15 RL = 150 to V+/2 0.21 0.55 + Sourcing to V /2 60 30 95 Sinking from V+/2 50 15 75 V mA 100 mA 80 dB IOUT Output Current VO = 0.5V from either Supply PSRR Power Supply Rejection Ratio 15V V+ 17V IS Supply Current No Load 4 RIN Common Mode Input Resistance AV = +1, f = 1 kHz, RS = 1 M 32 CIN Common Mode Input Capacitance AV = +1, RS = 100 k 1.7 ROUT Output Resistance Closed Loop RF = 10 k, f = 1 kHz, AV = -1 72 Units 0.1 RF = 10 k, f = 1 MHz, AV = -1 0.3 DG Differential Gain NTSC, AV = +2 RL = 150 to V+/2 0.12 DP Differential Phase NTSC, AV = +2 RL = 150 to V+/2 0.12 6.5 7.8 mA M pF % deg Note 1: Absolute maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Note 2: Human body model, 1.5 k in series with 100 pF. Machine Model, 0 in series with 200 pF. Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150 C Short circuit test is a momentary test. Output short circuit duration is infinite for VS < 6V at room temperature and below. For VS > 6V, allowable short circuit duration is 1.5 ms. Note 4: The maximum power dissipation is a function of TJ(MAX), JA , and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX)-TA ) / JA. All numbers apply for packages soldered directly onto a PC board. Note 5: Typical Values represent the most likely parametric norm. Note 6: All limits are guaranteed by testing or statistical analysis. Note 7: Positive current corresponds to current flowing into the device. Note 8: Slew rate is the average of the rising and falling slew rates Note 9: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that TJ = TA. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self-heating where TJ > TA. www.national.com 4 LMH6640 Connection Diagram 5-Pin SOT23 20086223 Top View Ordering Information Package 5-Pin SOT23 Part Number LMH6640MF LMH6640MFX Package Marking Transport Media 1k Units Tape and Reel AH1A 3k Units Tape and Reel 5 NSC Drawing MF05A www.national.com LMH6640 Typical Performance Characteristics At TJ = 25C, V+ = 16 V, V- = 0V, RF = 330 for AV= +2, RF = 1 k for AV = -1. RL tied to V /2. Unless otherwise specified. + IS vs. VS for Various Temperature IS vs. VCM for Various Temperature 20086220 20086221 IB vs. VS for Various Temperature IB vs. VS for Various Temperature 20086218 20086219 VOS vs. VS for Various Temperature (Typical Unit) IOS vs. VS for Various Temperature 20086216 www.national.com 20086227 6 1 k for AV = -1. RL tied to V+/2. Unless otherwise specified. (Continued) Positive Output Saturation Voltage vs. VS for Various Temperature Negative Output Saturation Voltage vs. VS for Various Temperature 20086224 20086228 Output Sourcing Saturation Voltage vs. ISOURCING for Various Temperature Output Sinking Saturation Voltage vs. ISINKING for Various Temperature 20086230 20086231 Input Current Noise vs. Frequency Input Voltage Noise vs. Frequency 20086204 20086205 7 www.national.com LMH6640 Typical Performance Characteristics At TJ = 25C, V+ = 16 V, V- = 0V, RF = 330 for AV= +2, RF = LMH6640 Typical Performance Characteristics At TJ = 25C, V+ = 16 V, V- = 0V, RF = 330 for AV= +2, RF = 1 k for AV = -1. RL tied to V+/2. Unless otherwise specified. (Continued) Gain vs. Frequency Normalized (PIN= -30 dBm) Gain vs. Frequency Normalized (PIN=-30dBm) 20086206 20086207 Gain vs. Frequency for Various VS (PIN = -30 dBm) Gain vs. Frequency for Various VS (PIN = -30 dBm) 20086209 20086210 Relative Gain vs. Frequency for Various Temperature (PIN = -10 dBm) Open Loop Gain & Phase vs. Frequency for Various Temperature (PIN = -30 dBm) 20086233 www.national.com 20086232 8 1 k for AV = -1. RL tied to V+/2. Unless otherwise specified. (Continued) Large Signal Transition Large Signal Transition 20086213 20086214 Small Signal Pulse Response Small Signal Pulse Response 20086215 20086208 Large Signal Pulse Response Large Signal Pulse Response 20086211 20086212 9 www.national.com LMH6640 Typical Performance Characteristics At TJ = 25C, V+ = 16 V, V- = 0V, RF = 330 for AV= +2, RF = LMH6640 Typical Performance Characteristics At TJ = 25C, V+ = 16 V, V- = 0V, RF = 330 for AV= +2, RF = 1 k for AV = -1. RL tied to V+/2. Unless otherwise specified. (Continued) PSRR vs. Frequency CMRR vs. Frequency 20086201 20086217 Closed Loop Output Resistance vs. Frequency Harmonic Distortion 20086203 20086226 0.1 dB Gain Flatness vs. Frequency Normalized Output Power vs. Input Power (AV = +1) 20086202 www.national.com 20086229 10 1 k for AV = -1. RL tied to V+/2. Unless otherwise specified. (Continued) Differential Gain/Phase vs. IRE 20086225 * The sum of all the capacitors and resistors in the R-C ladder is the total VCOM capacitance and resistance respectively. This total varies from panel to panel; capacitance could range from 50 nF-200 nF and the resistance could be anywhere from 20-100. * The number of ladder sections has been reduced to a number (4 sections in this case) which can easily be put together in the lab and which behaves reasonably close to the actual load. In this example, the LMH6640 was tested under the simulated conditions of total 209 nF capacitance and 54 as shown in Figure 1. Application Notes With its high output current and speed, one of the major applications for the LMH6640 is the VCOM driver in a TFT panel. This application is a specially taxing one because of the demands it places on the operational amplifier's output to drive a large amount of bi-directional current into a heavy capacitive load while operating under unity gain condition, which is a difficult challenge due to loop stability reasons. For a more detailed explanation of what a TFT panel is and what its amplifier requirements are, please see the Application Notes section of the LM6584 found on the web at: http://www.national.com/ds.cgi/LM/LM6584.pdf Because of the complexity of the TFT VCOM waveform and the wide variation in characteristics between different TFT panels, it is difficult to decipher the results of circuit testing in an actual panel. The ability to make simplifying assumptions about the load in order to test the amplifier on the bench allows testing using standard equipment and provides familiar results which could be interpreted using standard loop analysis techniques. This is what has been done in this application note with regard to the LMH6640's performance when subjected to the conditions found in a TFT VCOM application. Figure 1, shows a typical simplified VCOM application with the LMH6640 buffering the VCOM potential (which is usually around 12 of panel supply voltage) and looking into the simplified model of the load. The load represents the cumulative effect of all stray capacitances between the VCOM node and both row and column lines. Associated with the capacitances shown, is the distributed resistance of the lines to each individual transistor switch. The other end of this R-C ladder is driven by the column driver in an actual panel and here is driven with a low impedance MOSFET driver (labeled "High Current Driver") for the purposes of this bench test to simulate the effect that the column driver exerts on the VCOM load. The modeled TFT VCOM load, shown in Figure 1, is based on the following simplifying assumptions in order to allow for easy bench testing and yet allow good matching results obtained in the actual application: 20086235 FIGURE 1. LMH6640 in a VCOM Buffer Application with Simulated TFT Load RS is sometimes used in the panel to provide additional isolation from the load while RF2 provides a more direct feedback from the VCOM. RF1, RF2, and RS are trimmed in the actual circuit with settling time and stability trade-offs considered and evaluated. When tested under simulated load conditions of Figure 1, here are the resultant voltage and current waveforms at the LMH6640 output: 11 www.national.com LMH6640 Typical Performance Characteristics At TJ = 25C, V+ = 16 V, V- = 0V, RF = 330 for AV= +2, RF = LMH6640 Application Notes (Continued) 20086236 FIGURE 2. VCOM Output, High Current Drive Waveform, & LMH6640 Output Current Waveforms 20086237 FIGURE 3. Expanded View of Figure 2 Waveforms showing LMH6640 Current Sinking 12 Cycle combination of all these features is not readily available in the market, especially in the space saving SOT23-5 package. All this performance is achieved at the low power consumption of 65 mW which is of utmost importance in today's battery driven TFT panels. As can be seen, the LMH6640 is capable of supplying up to 160 mA of output current and can settle the output in 4.4 s. The LMH6640 is a cost effective amplifier for use in the TFT VCOM application and is made even more attractive by its large supply voltage range and high output current. The www.national.com 12 inches (millimeters) 5-Pin SOT23 NS Product Number MF05A National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 LMH6640 TFT-LCD Single, 16V Rail-to-Rail High Output Operational Amplifier Physical Dimensions unless otherwise noted IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated