AS1910 - AS1915
Dual-Voltage Microprocessor Supervisory Circuits with Manual Reset
and Watchdog
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 1 - 16
Datasheet
1 General Description
The AS1910 - AS1915 microprocessor supervisory circuits were
designed to generate a reset when one of the two monitored supply
voltages falls below a factory-trimmed threshold, and to maintain the
reset for a minimum timeout period when both supplies are above
their reset thresholds. Guaranteed to be in the correct state for VCC
higher than +1.0V, these devices are ideal for multiple-voltage
systems with strict monitoring requirements.
The AS1913/AS1914/AS1915 feature factory-trimmed thresholds to
monitor a primary voltage between 1.8 and 3.6V, and a secondary
voltage between 0.9 and 2.5V.
For the AS1910/AS1911/AS1912, a secondary monitoring voltage
can be user-adjusted via an external resistor divider down to 0.6V.
The devices are available with the reset output types listed in Table
1.
The AS1910 - AS1915 include a manual-reset input for systems that
never fully power down the microprocessor. Additionally, these
devices feature a watchdog timer to help ensure that the processor is
operating within proper code boundaries.
The AS1910 - AS1915 are available in a 6-pin SOT23 package.
Figure 1. Typical Application Diagram
2 Key Features
Primary VCC Supervisory Range: +1.8 to +3.6V
Secondary VCC Supervisory Range: +0.9 to +2.5V (AS1913/
AS1914/AS1915)
User-Adjustable Threshold Down to +0.63V (AS1910/AS1911/
AS1912)
Guaranteed Reset Valid Down to VCC = +1.0V
Reset Timeout Delay: 215ms
Manual Reset Input
Three Reset Output Types:
- Active-High Push/Pull
- Active-Low Push/Pull
- Active-Low Open-Drain
Watchdog Timeout Period: 1.5s
Immune to Fast Negative VCC Transients
External Components Not Required
Operating Temperature Range: -40 to +125ºC
6-pin SOT23 Package
3 Applications
The devices are ideal for portable and battery-powered systems,
embedded controllers, intel lig ent instruments, automotive sys tem s,
critical CPU monitoring, and any multi-supply application.
Table 1. Standard Products
Model Reset Output Type
AS1910/AS1913 Active-Low Push/Pull
AS1911/AS1914 Active-High Push/Pull
AS1912/AS1915 Active-Low Open-Drain
External
Reset
CPU
Core
Supply
I/O Supply
VCC
VCC2
GND
RESETN
I/O
4
WDI
6
VCC
3
MRN
GND 2
1
RESETN
5
VCC2 AS1913/
AS1915
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 2 - 16
AS1910 - AS1915
Datasheet - Pin Assignments
4 Pin Assignments
Figure 2. Pin Assignments (Top View)
4.1 Pin Descriptions
Table 2. Pin Descriptions
Pin Number Pin Name Description
1
RESETN
Active-Low Reset Output (AS1910, AS1912, AS1913, AS1915). The RESETN signal toggles from high to low
when VCC, VCC2, or RESETIN input drops below the factory-trimmed reset threshold (see Table 4 on page 4),
or MRN is pulled low , or the watchdog triggers a reset. This output signal remains low for the reset timeout period
after all supervised voltages exceed their reset threshold, or MRN goes low to high, or the watchdog triggers a
reset.
RESET
Active-High Reset Output (AS1911, AS1914). The RESET signal toggles from low to high when VCC, VCC2, or
RESETIN input drops below the factory-trimmed reset threshold (see Table 4 on page 4), or MRN is pulled low,
or the watchdog triggers a reset. This output signal remains high for the reset timeout period (see tRP on page 5)
after all supervised voltages exceed their reset threshold, or MRN goes low to high, or the watchdog triggers a
reset.
2GND
Ground
3MRN
Active-Low Manual Reset Input. Pulling this pin low asserts a reset. This pin is connected to the internal 50kΩ
pullup to VCC. This reset remains active as long as MRN is low and for the reset timeout period (see tRP on
page 5) after MRN goes high.
Note: If the manual reset feature is not used, this pin should be unconnected or connected to VCC.
4WDI
Wa tchdog Input. If WDI remains high or low for longer than the watchdog timeout period (see tWD on page 6),
the internal watchdog timer period expires and a reset is triggered for the reset timeout period (see tRP on page
5). The internal watchdog timer clears whenever a reset is a asserted or when WDI senses a rising or falling
edge.
Note: To disable the watchdog feature, this pin must be unconnected or connected to a tri-state buffer output.
WDI must be low or unconnected (tristate) during the reset timeout period tRP, (see Figure 13 on page 10).
5RESETIN User-Adjustable Supervised Voltage Input (AS1910/AS191 1/AS1912). This high-impedance pin serves as the
input to the internal reset comparator. Connect this pin to an external resistor-divider network to set the reset
threshold voltage (down to 0.63V).
VCC2 Primary Supervised Voltage Input (AS1913/AS1914/AS1915). This pin serves as the secondary supervised
voltage input.
6VCC
Primary Supervised Voltage Input. This pin serves as the primary supervised voltage input.
AS1910 -
AS1915
2
GND
3
MRN
1
RESETN/RESET
4WDI
5RESETIN/VCC2
6VCC
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 3 - 16
AS1910 - AS1915
Datashee t - A b s o l u t e M a x i mu m R a t i n g s
5 Absolute Maximum Ratings
Stresses beyond those listed in Table 3 may cause permanent damage to the device. These are stress ratings only, and functional operation of
the device at these or any other conditions beyond those indicated in Electrical Characteristics on page 4 is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect device reliability.
Table 3. Absolute Maximum Ratings
Parameter Min Max Units Comments
Electrical Parameters
VCC, VCC2 to GND -0.3 +5.0 V
Open-Drain RESETN -0.3 +7.0 V
Push/Pull RESET, RESETN -0.3 VCC +
0.3 V
MRN, WDI, RESETIN to GND -0.3 VCC +
0.3 V
Input Current (VCC)20mA
Output Current (RESET, RESETN) 20 mA
Continuous Power Dissipation
Continuous Power Dissipation
(TAMB = +70ºC) 696 mW Derate 8.7mW/ºC above +70ºC
Temperature Ranges and Storage Conditions
Junction Temperature +150 ºC
Storage Temperature Range -55 +150 ºC
Package Body Temperat ure +260 ºC
The reflow peak soldering temperature (body temperature)
specified is in accordance with IPC/JEDEC J-STD-020
“Moisture/Reflow Sensitiv ity Cl ass ific ati on for Non-
Hermetic Solid State Surface Mount Devices”.
The lead finish for Pb-free leaded packages is matte tin
(100% Sn).
Humidity non-condensing 885%
Moisture Sensitive Level 1 Represents a max. floor life time of unlimited
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 4 - 16
AS1910 - AS1915
Datasheet - Electrical Characteristics
6 Electrical Characteristics
VCC = +2.7 to +3.6V for AS19xx-T/S/R, VCC = +2.1 to +2.75V for AS19xx- Z/Y, VCC = +1.53 to +2.0V for AS19xx-W/V; Typical values @ TAMB
= +25ºC (unless otherwise specified).
Table 4. Electrical Characteristics
Symbol Parameter 1Conditions Min Typ Max Units
TAMB Operatin g Temperature Range -40 +125 ºC
VCC Operating Voltage Range TAMB = 0 to +85ºC 1.0 3.6 V
TAMB = -40 to +125ºC 1.2 3.6
ICC VCC Supply Current
(MRN and WDI Not Connected)
VCC = +3.6V, No Load,
TAMB = -40ºC to +85ºC 5.8 13 µA
VCC = +3.6V, No Load,
TAMB = -40 to +125ºC 21
ICC2 VCC2 Supply Current VCC2 = +2.5V 2 µA
VTH VCC Reset Threshold
(VCC Falling)
TAMB = -40 to +85ºC AS19xx-T 2.994 3.08 3.154
V
TAMB = -40 to +125ºC 2.972 3.179
TAMB = -40 to +85ºC AS19xx-S 2.848 2.93 3.000
TAMB = -40 to +125ºC 2.827 3.024
TAMB = -40 to +85ºC AS19xx-R 2.556 2.63 2.693
TAMB = -40 to +125ºC 2.538 2.714
TAMB = -40 to +85ºC AS19xx-Z 2.255 2.32 2.376
TAMB = -40 to +125ºC 2.239 2.394
TAMB = -40 to +85ºC AS19xx-Y 2.129 2.19 2.243
TAMB = -40 to +125ºC 2.113 2.260
TAMB = -40 to +85ºC AS19xx-W 1.623 1.67 1.710
TAMB = -40 to +125ºC 1.612 1.723
TAMB = -40 to +85ºC AS19xx-V 1.536 1.58 1.618
TAMB = -40 to +125ºC 1.525 1.631
VTH2 VCC2 Reset Threshold
TAMB = -40 to +85ºC AS19xx-Z 2.237 2.313 2.387
V
TAMB = -40 to +125ºC 2.232 2.394
TAMB = -40 to +85ºC AS19xx-Y 2.116 2.188 2.258
TAMB = -40 to +125ºC 2.111 2.265
TAMB = -40 to +85ºC AS19xx-W 1.610 1.665 1.718
TAMB = -40 to +125ºC 1.607 1.723
TAMB = -40 to +85ºC AS19xx-V 1.523 1.575 1.625
TAMB = -40 to +125ºC 1.520 1.630
TAMB = -40 to +85ºC AS19xx-I 1.342 1.388 1.432
TAMB = -40 to +125ºC 1.339 1.437
TAMB = -40 to +85ºC AS19xx-H 1.270 1.313 1.355
TAMB = -40 to +125ºC 1.267 1.359
TAMB = -40 to +85ºC AS19xx-G 1.073 1.11 1.146
TAMB = -40 to +125ºC 1.071 1.149
TAMB = -40 to +85ºC AS19xx-F 1.015 1.05 1.084
TAMB = -40 to +125ºC 1.013 1.087
TAMB = -40 to +85ºC AS19xx-E 0.806 0.833 0.860
TAMB = -40 to +125ºC 0.804 0.862
TAMB = -40 to +85ºC AS19xx-D 0.762 0.788 0.813
TAMB = -40 to +125ºC 0.760 0.816
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 5 - 16
AS1910 - AS1915
Datasheet - Electrical Characteristics
Reset Threshold
Temperature Co efficient 60 ppm/ºC
Reset Threshold Hysteresis 8 x VTH mV
VRESETIN
TH RESETIN Threshold VRESETINTH Falling, TAMB = 0 to +85ºC 0.615 0.630 0.645 V
TAMB = -40 to +125ºC 0.61 0.65
RESETIN Hysteresis 8 x VTH mV
IRESETIN RESETIN Input Current 2TAMB = -40 to +85ºC -25 +25 nA
TAMB = -40 to +125ºC -100 +100
tRD VCC to Reset
Output Delay VCC = VTH to (VTH - 100mV) 55 µs
RESETIN to Reset
Output Delay VRESETIN = VRESETINTH to
(VRESETINTH - 30mV) 45 µs
tRP Reset Timeout Period TAMB = -40 to +85ºC 140 215 280 ms
TAMB = -40 to +125ºC 100 320
VOL RESETN Output Low
(Push/Pull or Open-Drain)
VCC 1.0V, ISINK = 50µA,
Reset Asserted, TAMB = 0 to +85ºC 0.3
V
VCC 1.2V, ISINK = 100µ A, Reset Asserted 0.3
VCC 2.55V, ISINK = 1.2mA,
Reset Asserted 0.3
VCC 3.3V, ISINK = 3.2mA,
Reset Asserted 0.4
VOH RESETN Output High
(Push/Pull Only)
VCC 1.8V, ISOURCE = 200µA,
Reset Not Asserted 0.8 x
VCC
V
VCC 3.15V, ISOURCE = 500µA,
Reset Not Asserted 0.8 x
VCC
VCC 3.3V, ISOURCE = 800µA,
Reset Not Asserted 0.8 x
VCC
ILKG Open-Drain RESETN Output Leakage
Current RESETN Not Asserted 1.0 µA
TAMB = +25 º C 0.2
VOH RESET Output High
(Push/Pull Only)
VCC 1.0V, ISOURCE = 1µA,
Reset Asserted, TAMB = 0 to +85ºC 0.8 x
VCC
V
VCC 1.50V, ISOURCE = 100µA,
Reset Asserted 0.8 x
VCC
VCC 2.55V, ISOURCE = 500µA,
Reset Asserted 0.8 x
VCC
VCC 3.3V, ISOURCE = 800µA,
Reset Asserted 0.8 x
VCC
VOL RESET Output Low
(Push/Pull Only)
VCC 1.8V, ISINK = 500µA,
Reset Asserted 0.3
V
VCC 3.15V, ISINK = 1.2mA,
Reset Asserted 0.3
VCC 3.3V, ISINK = 3.2mA,
Reset Asserted 0.4
Manual Reset Input
VIL MRN Input voltage
0.3 x
VCC V
VIH 0.7 x
VCC
MRN Minimum Input Pulse 1 µs
MRN Transient Rejection 90 ns
Table 4. Electrical Characteristics
Symbol Parameter 1Conditions Min Typ Max Units
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 6 - 16
AS1910 - AS1915
Datasheet - Electrical Characteristics
MRN to Reset Delay 130 ns
MRN Pullup Resistance 25 50 75 kΩ
Wa tchdog Input
tWD Watchdog Timeout Period TAMB = -40 to +85ºC 1.12 1.5 2.4 s
TAMB = -40 to +125ºC 0.80 2.60
tWDI WDI Pulse Width 220 ns
VIL WDI Input Voltage
0.3 x
VCC V
VIH 0.7 x
VCC
IWDI WDI Input Current WDI = VCC, Time Average 80 160 µA
WDI = 0, Time Average -20 -11
1. Over-temperature limits are guaranteed by design and not production tested. Devices tested at +25ºC.
2. Guaranteed by design and not production tested.
Note: All limits are guaranteed. The parameters with min and max values are guaranteed with production tests or SQC (Statistical Quality
Control) methods.
Table 4. Electrical Characteristics
Symbol Parameter 1Conditions Min Typ Max Units
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 7 - 16
AS1910 - AS1915
Datasheet - Typical Operating Characteristics
7 Typical Operating Characteristics
TAMB = +25ºC (unless otherwise specified).
Figure 3. Normalized Reset Threshold Delay vs. Figure 4. VOUT vs. VCC; VCC2 = 2.50V, VTH = 1.58V
Temperature Active-Low (Typ)
Figure 5. Reset Timeout Period vs. Temperature Figure 6. Supply Current vs. Temperature
Figure 7. VOH vs. ISOURCE; VCC = 3.2V Figure 8. VOL vs. ISINK; VCC = 3.2V
-0.50
0.00
0.50
1.00
1.50
2.00
2.50
3.00
3.50
4.00
4.50
5.00
5.50
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5
VCC (V)
Output Voltage (V) e
0.94
0.96
0.98
1
1.02
1.04
1.06
-40 -20 0 20 40 60 80 100 120
Temperature (°C)
Reset Threshold (V) e
3
4
5
6
7
8
9
10
-50 -25 0 25 50 75 100 125
Temperature (°C)
VCC Supply Current (µA) e
VCC = 3.08V T Version
VCC = 1.58V V Version
150
160
170
180
190
200
210
220
230
240
250
-40 -20 0 20 40 60 80 100 120
Temperature (°C)
Reset Timeout Periode (ms)
2.9
2.95
3
3.05
3.1
3.15
3.2
3.25
0 0.2 0.4 0.6 0.8 1 1.2
ISOURCE (mA)
VOUT (V) ]
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
01234567
ISINK (mA)
VOUT (V) e
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 8 - 16
AS1910 - AS1915
Datasheet - Detailed Descripti on
8 Detailed Description
The AS1910 - AS1915 supervisory circuits were designed to generate a reset when one of the two monitored supply voltages falls below its
factory-trimmed trip threshold (see VTH on page 4 and VTH2 on page 4), and to maintain the reset for a minimum timeout period (see tRP on
page 5) after all supplies have stabilized.
The integrated watchdog timer (see Watchdog Input on page 10) helps mitigate against bad programming code or clock signals, and/or poor
peripheral response. An active-low manual reset input (see Manual Reset Input on page 10) allows for an externally activated system reset.
8.1 RESET/RESETN
Whenever one of the monitored voltages falls below its reset threshold, the RESET output (AS1910, AS1912, AS1913, AS1915) asserts low or
the RESETN output (AS1911, AS1914) asserts high. Once all monitored voltages have stabilized, an internal timer keeps the reset asserted for
the reset timeout period (tRP). After the tRP period, the RESET or RESETN output return to their original state (see Figure 10).
Figure 9. Functional Diagram of VCC Supervisory Application
Figure 10. Reset Timing Diagram
AS1913/AS1914/AS1915
Reset Timeout Delay
Generator
Watchdog Transition
Detector Watchdog
Timer
+
1.26V
VCC
0.63V
1.26V
5
VCC2
2
GND
6
VCC
4
WDI
1
RESETN/
RESET
3
MRN
1V
tRD
tRP
tRP tRD
VTHVTH
VCC
RESETN
RESET
GND
1V
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 9 - 16
AS1910 - AS1915
Datasheet - Detailed Descripti on
Figure 11. Functional Diagram of RESETIN Supervisory Application
8.2 RESETIN
The AS1910/AS1911/AS1912 feature a user-adjustable supervisory voltage input (RESETIN). The threshold voltage for RESETIN is between
0.61 and 0.65V (0.63 typ).
Figure 12. Voltage Monitoring Circuit
To monitor a voltage higher than 0.63V, connect a resistor divider network to the circuit as shown in Figure 12. For the circuit shown in Figure 12,
the threshold at VMONITOR is: VMONITOR_TRIP = 0.63V [(R1 + R2)/R2](EQ 1)
Note: Since RESETIN is powered by VCC, VRESETIN must not be larger than VCC.
AS1910/AS1911/AS1912
Reset Timeout Delay
Generator
Watchdog Transition
Detector Watchdog
Timer
VCC
0.63V
+
1.26V
2
GND
1
RESETN/
RESET
5
RESETIN
6
VCC
4
WDI
3
MRN
AS1910/AS1911/
AS1912
R1
R2
VMONITOR
VCC VRESETIN
5
RESETIN
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 10 - 16
AS1910 - AS1915
Datasheet - Detailed Descripti on
8.3 Watchdog Input
The integrated watchdog feature can be used to monitor processor activity via pin WDI, and can detect pulses as short as 50ns. The watchdog
requires that the processor toggle the watchdog logic input at regular intervals, within a specified minimum timeout period (1.5s, typ). A reset is
asserted for the reset timeout period. As long as reset is asserted, the timer remains cleared and is not incremented. When reset is deasserted,
the watchdog timer starts counting (Figure 11).
Note: The watchdog timer can be cleared with a reset pulse or by toggling WDI.
Figure 13. Watchdog Timing Relationship
The watchdog is internally driven low during most (87.5%) of the watchdog timeout period (see tWD on page 6) and high for the rest of the
watchdog timeout period. When pin WDI is left unconnected, this internal driver clears the watchdog timer every 1.4s. When WDI is tri-stated or
is not connected, the maximum allowable leakage current is 10µA and the maximum allowable load capacitance is 200pF.
Note: The watchdog function can be disabled by leaving pin WDI unconnected or connecting it to a tri-state output buffer.
8.4 Manual Reset Input
The active-low pin MRN is used to force a manual reset. This input can be driven by CMOS logic levels or with open-drain collector outputs.
Pulling MRN low asserts a reset which will remain asserted as long as MRN is kept low, and for the timeout period (see tRP on page 5) after
MRN goes high (140ms min). The manual reset circuitry has an internal 50kΩ pullup resistor, thus it can be left open if not used.
To create a manual-reset circuit, connect a normally open momentary switch from pin MRN to GND (see Figure 1 on page 1); external debounce
circuitry is not required in this configuration.
If MRN is driven via long cables or the device is used in a noisy environment, a 0.1µF capacitor between pin MRN and GND will provide
additional noise immunity.
tRST
The RESET signal is the inverse of the RESETN signal.
tWD
VCC
RESETN
WDI
tRP
tRP
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 11 - 16
AS1910 - AS1915
Datasheet - Application Information
9 Application Information
9.1 Watchdog Input Current
The watchdog input is driven through an internal buffer and an internal series resistor from the watchdog timer (see Figure 11 on page 9). When
pin WDI is left unconnected (watchdog disabled), the watchdog timer is serviced within the watchdog timeout period (see tWD on page 6) by a
low-high-low pulse from the counter chain. For minimum watchdog input current (minimum overall power consumption), pull WDI low for most of
the watchdog timeout period, pulsing it low-high-low once within the first 7/8 (87.5%) of the watchdog timeout period to reset the watchdog timer .
Note: If WDI is externally driven high for the majority of the timeout period, up to 160µA can flow into pin WDI.
9.2 Interfacing to Bi-Directional CPU Reset Pins
Since the reset outputs of the AS1912 and AS1915 are open drain, these devices interface easily with processors that have bi-directional reset
pins. Connecting the processor reset output directly to the AS1912/AS1915 RESETN pin with a single pullup resistor (see Figure 14) allows the
AS1912/AS1912 to assert a reset.
Figure 14. AS1912 or AS1915 RESETN-to-CPU Bi-Directional Reset Pin
9.3 Fast Negative-Going Transients
Fast, negative-going VCC transients normally do not require the CPU to be shutdown. The AS1910 - AS1915 are virtually immune to such
transients. Resets are issued to the CPU during power-up, powerdown, and brownout conditions.
Note: VCC transients that go 100mV below the reset threshold and last 55µs typically will not assert a reset pulse.
9.4 Valid Reset to VCC = 0
The AS1910 - AS1915 are guaranteed to operate properly down to VCC = 1V. For applications requiring valid reset levels down to VCC = 0, a
pulldown resistor to active-low outputs (push/pull only) and a pullup resistor to active-high outputs (push/pull only) will ensure that the reset line
is valid during the interval where the reset output can no longer sink or source current.
9.5 Watchdog Tips
Careful consideration should be taken when implementing the AS1910 - AS1915 watchdog feature.
One method of supervising software code execution is to set/reset the watchdog input at different places in the code, rather than pulsing the
watchdog input high-low-high or low-high-low. This method avoids a loop condition in which the watchdog timer would continue to be reset inside
the loop, preventing the watchdog from ever timing out.
Figure 15 shows a flowchart where the input/output driving the watchdog is set high at the beginning of the routine, set low at the beginning of
every subroutine, then set high again when the routine returns to the beginning. If the routine should hang in a subroutine, the problem would
quickly be corrected, since the I/O is continually set low and the watchdog timer is allowed to time out, causing a reset or interrupt to be issued
(see Watchdog Input Current on page 11). This method results in higher averaged WDI input current over time than a case where WDI is held
low for the majority (87.5%) of the timeout period and periodically pulsing it low-high-low.
AS1912/
AS1915
CPU
Reset
Generator
VCC
RESETN
GND
VCC
1
RESETN
GND 2
VCC 6
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 12 - 16
AS1910 - AS1915
Datasheet - Application Information
Figure 15. Example Watchdog Programming Flowchart
Start
Set WDI
High
Subroutine or
Program Loop
Set WDI Low
Return
Program
Code
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 13 - 16
AS1910 - AS1915
Datasheet - Package Drawings and Markings
10 Package Drawings and Markings
Figure 16. 6-pi n SOT23 Marking
Top Marking Bottom Marking
xxxx- encoded Datacode
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 14 - 16
AS1910 - AS1915
Datasheet - Package Drawings and Markings
Figure 17. 6-pin SOT23 Package
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 15 - 16
AS1910 - AS1915
Datasheet - Ordering Info rmation
11 Ordering Information
The devices are available as the standard products shown in Table 5.
Note: All products are RoHS compliant and austriamicrosystems green.
Buy our products or get free samples online at ICdirect: http://www.austriamicrosystems.com/ICdirect
Technical Support is found at http://www.austriamicrosystems.com/Technical-Support
For further information and requests, please contact us mailto:sales@austriamicrosystems.com
or find your local distributor at http://www.austriamicrosystems.com/distributor
Table 5. Ordering Information
Ordering Code Marking Reset Output Type Thresholds Delivery Form Package
AS1910S-T ASH3 Active-Low Push/Pull 2.93V, Adjustable Tape and Reel 6-pin SOT23
AS1910R-T ASH4 Active-Low Push/Pull 2.63V, Adjustable Tape and Reel 6-pin SOT23
AS1910Z-T ASH5 Active-Low Push/Pull 2.32V, Adjustable Tape and Reel 6-pin SOT23
AS1910V-T ASH6 Active-Low Push/Pull 1.58V, Adjustable Tape and Reel 6-pin SOT23
AS1911S-T ASH7 Active High Push/Pull 2.93V, Adjustable Tape and Reel 6-pin SOT23
AS1911R-T ASH8 Active High Push/Pull 2.63V, Adjustable Tape and Reel 6-pin SOT23
AS1911Z-T ASH9 Active High Push/Pull 2.32V, Adjustable Tape and Reel 6-pin SOT23
AS1911V-T ASIA Active High Push/Pull 1.58V, Adjustable Tape and Reel 6-pin SOT23
AS1912S-T ASIB Open Drain 2.93V, Adjustable Tape and Reel 6-pin SOT23
AS1912R-T ASIC Open Drain 2.63V, Adjustable Tape and Reel 6-pin SOT23
AS1912Z-T ASID Open Drain 2.32V, Adjustable Tape and Reel 6-pin SOT23
AS1912V-T ASIE Open Drain 1.58V, Adjustable Tape and Reel 6-pin SOT23
AS1913TZ-T ASIF Active-Low Push/Pull 3.08V, 2.313V Tape and Reel 6-pin SOT23
AS1913SF-T ASIG Active-Low Push/Pull 2.93V,1.05V Tape and Reel 6-pin SOT23
AS1913VD-T ASIH Active-Low Push/Pull 1.58V, 0.788V Tape and Reel 6-pin SOT23
AS1914TZ-T ASII Active High Push/Pull 3.08V, 2.313V Tape and Reel 6-pin SOT23
AS1914SF-T ASIJ Active High Push/Pull 2.93V,1.05V Tape and Reel 6-pin SOT23
AS1914VD-T ASIK Active High Push/Pull 1.58V, 0.788V Tape and Reel 6-pin SOT23
AS1915TZ-T ASIL Open-Drain 3.08V, 2.313V Tape and Reel 6-pin SOT23
AS1915SF-T ASIM Open-Drain 2.93V,1.05V Tape and Reel 6-pin SOT23
AS1915VD-T ASIN Open-Drain 1.58V, 0.788V Tape and Reel 6-pin SOT23
www.austriamicrosystems.com/Supervisors/AS1910 Revision 1.03 16 - 16
AS1910 - AS1915
Datasheet
Copyrights
Copyright © 1997-2010, austriamicrosystems AG, Tobelbaderstrasse 30, 8141 Unterpremstaetten, Austria-Europe. Trademarks Registered ®.
All rights reserved. The material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of
the copyright owner.
All products and companies mentioned are trademarks or registered trademarks of their respective companies.
Disclaimer
Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing in its Term of Sale.
austriamicrosystems AG makes no warranty, express, statutory , implied, or by description regarding the information set forth herein or regarding
the freedom of the described devices from patent infringement. austriamicrosystems AG reserves the right to change specifications and prices at
any time and without notice. Therefore, prior to designing this product into a system, it is necessary to check with austriamicrosystems AG for
current information. This product is intended for use in normal commercial applications. Applications requiring extended temperature range,
unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are
specifically not recommended without additional processing by austriamicrosystems AG for each application. For shipments of less than 100
parts the manufacturing flow might show deviations from the standard production flow, such as test flow or test location.
The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However, austriamicrosystems AG shall not
be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use,
interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing,
performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of
austriamicrosystems AG rendering of technical or other services.
Contact Information
Headquarters
austriamicrosyste ms AG
Tobelbaderstrasse 30
A-8141 Unterpremstaetten, Austria
Tel: +43 (0) 3136 500 0
Fax: +43 (0) 3136 525 01
For Sales Offices, Distributors and Representa tive s, plea se vis it:
http://www.austriamicrosystems.com/contact