TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com 800-mA SYNCHRONOUS STEP-DOWN CONVERTER Check for Samples: TPS62052, TPS62054, TPS62056, TPS62050, TPS62051 FEATURES DESCRIPTION * The TPS6205x devices are a family of high-efficiency synchronous step-down dc/dc converters ideally suited for systems powered from a 1-cell or 2-cell Li-Ion battery or from a 3-cell to 5-cell NiCd, NiMH, or alkaline battery. 1 2 * * * * * * * * * * * High-Efficiency Synchronous Step-Down Converter With up to 95% Efficiency 12-A Quiescent Current (Typ) 2.7-V to 10-V Operating Input Voltage Range Adjustable Output Voltage Range From 0.7 V to 6 V Fixed Output Voltage Options Available in 1.5 V, 1.8 V, and 3.3 V Synchronizable to External Clock Signal up to 1.2 MHz High Efficiency Over a Wide Load Current Range in Power-Save Mode 100% Maximum Duty Cycle for Lowest Dropout Low Noise Operation in Forced Fixed Frequency PWM Operation Mode Internal Softstart Overtemperature and Overcurrent Protected Available in 10-Pin Microsmall Outline Package MSOP The TPS62050 is a synchronous PWM converter with integrated N-channel and P-channel power MOSFET switches. Synchronous rectification increases efficiency and reduces external component count. To achieve highest efficiency over a wide load current range, the converter enters a power-saving pulse-frequency modulation (PFM) mode at light load currents. Operating frequency is typically 850 kHz, allowing the use of small inductor and capacitor values. The device can be synchronized to an external clock signal in the range of 600 kHz to 1.2 MHz. For low noise operation, the converter can be programmed into forced-fixed frequency in PWM mode. In shutdown mode, the current consumption is reduced to less than 2 A. The TPS6205x is available in the 10-pin (DGS) micro-small outline package (MSOP) and operates over an free air temperature range of -40C to 85C. APPLICATIONS * * * * Cellular Phones Organizers, PDAs, and Handheld PCs Low Power DSP Supply Digital Cameras and Hard Disks TYPICAL APPLICATION CIRCUIT VI = 3.3 V to 10 V 1 8 VIN SW EN FB TPS62050 9 L1 = 10 H EFFICIENCY vs OUTPUT CURRENT VO = 1.5 V / 800 mA 100 90 5 80 TPS62052 6 70 PG LBI 7 3 Co = 22 F 2 SYNC GND 4 LBO PGND 10 Efficiency - % Ci = 10 F 60 50 40 30 20 10 0 0.01 VI = 7.2 V, VO = 5 V, SYNC = L 0.1 1 10 100 1k IO - Output Current - mA 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. MATHCAD is a registered trademark of Mathsoft Incorporated. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2002-2011, Texas Instruments Incorporated TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. Package/Ordering Information PACKAGED DEVICES OUTPUT VOLTAGE LBI/LBO FUNCTIONALITY PACKAGE MARKING TPS62050DGS Adjustable 0.7 V to 6 V Standard BFM TPS62051DGS Adjustable 0.7 V to 6 V Enhanced BGB TPS62052DGS 1.5 V Standard BGC TPS62054DGS 1.8 V Standard BGE TPS62056DGS 3.3 V Standard BGG PLASTIC MSOP (1) (DGS) (1) The DGS packages are available taped and reeled. Add an R suffix to the device type (i.e., TPS62050DGSR) to order quantities of 2500 devices per reel. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted (1) TPS6205x -0.3 V to 11 V Supply voltage, VI -0.3 V to VI Voltage at EN, SYNC -0.3 V to 7 V Voltage at LBI, FB, LBO, PG -0.3 V to 11 V (2) Voltage at SW Output current, IO 850 mA Maximum junction temperature, TJ 150C Operating free-air temperature range, TA -40C to 85C Storage temperature range, Tstg -65C to 150C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds (1) (2) 300C Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. The voltage at the SW pin is sampled in PFM mode 15 s after the PMOS has switched off. During this time the voltage at SW is limited to 7 V maximum. Therefore, the output voltage of the converter is limited to 7 V maximum. PACKAGE DISSIPATION RATING (1) PACKAGE TA 25C POWER RATING DERATING FACTOR TA 25C TA = 70C POWER RATING TA = 85C POWER RATING 10-PIN MSOP (1) 555 mW 5.56 mW/C 305 mW 221 mW The thermal resistance junction to ambient soldered onto a PCB of the 10-pin MSOP is 180C/W. RECOMMENDED OPERATING CONDITIONS MIN Supply voltage at VI 2.7 Voltage at PG, LBO (1) 2 MAX 10 6 Maximum output current Operating junction temperature NOM -40 UNIT V V 800 (1) mA 125 C Assuming no thermal limitation Copyright (c) 2002-2011, Texas Instruments Incorporated TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com ELECTRICAL CHARACTERISTICS VI = 7.2 V, VO = 3.3 V, IO = 300 mA, EN = VI, TA = -40C to 85C (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT SUPPLY CURRENT VI Input voltage range I(Q) Operating quiescent current I(SD) Shutdown current IQ(LBI) Quiescent current with enhanced LBI comparator version. 10 V IO = 0 mA, SYNC = GND, VI = 7.2 V 2.7 12 20 A EN = GND 1.5 5 EN = GND, TA=25C 1.5 3 EN = VI, LBI=GND, TPS62051 only A A 5 ENABLE VIH EN high level input voltage VIL EN low level input voltage 1.3 V 0.3 EN trip point hysteresis 100 Ilkg EN input leakage current EN = GND or VIN, VI = 7.2 V I(EN) EN input current 0.6 V V(EN) 4 V V(UVLO) Undervoltage lockout threshold 0.01 V mV 0.2 A 2 A 1.6 V POWER SWITCH rDS(on) rDS(on) P-channel MOSFET on-resistance VI 5.4 V; IO = 300 mA 400 650 VI = 2.7 V; IO = 300 mA 600 850 1 A 1200 1400 mA VI 5.4 V; IO = 300 mA 300 450 VI = 2.7 V; IO = 300 mA 450 550 P-channel MOSFET leakage current VDS = 10 V P-channel MOSFET current limit VI = 7.2V, VO = 3.3 V N-channel MOSFET on-resistance N-channel MOSFET leakage current 1000 VDS = 6 V 1 m m A POWER GOOD OUTPUT, LBI, LBO V(PG) Power good trip voltage Vml -2% Power good delay time VOL VO ramping positive 50 VO ramping negative 200 PG, LBO output low voltage V(FB) = 0.8 x VO nominal, I(sink) = 1 mA PG, LBO output leakage current V(FB) = VO nominal, V(LBI) = VI 0.01 Minimum supply voltage for valid power good, LBO signal V(LBI) Low battery input trip voltage s 0.3 V 0.25 A 2.3 Input voltage falling V 1.21 Low battery input trip point accuracy V(LBI,HY V V 1.5% Low battery input hysteresis 15 mV S) Ilkg(LBI) LBI leakage current 0.01 0.1 A 850 1000 kHz 1200 kHz OSCILLATOR fS Oscillator frequency 600 f(SYNC) Synchronization range 600 VIH SYNC high level input voltage 1.5 VIL SYNC low level input voltage Ilkg SYNC input leakage current SYNC = GND or VIN V 0.01 SYNC trip point hysteresis 0.3 V 0.1 A 100 Duty cycle of external clock signal mV 20% 90% 6.0 V 0.1 A OUTPUT VO Adjustable output voltage range TPS62050, TPS62051 0.7 V(FB) Feedback voltage TPS62050, TPS62051 0.5 FB leakage current TPS62050, TPS62051 Feedback voltage tolerance TPS62050, TPS62051 Copyright (c) 2002-2011, Texas Instruments Incorporated V 0.02 VI = 2.7 V to 10 V, 0 mA< IO< 600 mA -3% 3% 3 TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com ELECTRICAL CHARACTERISTICS (continued) VI = 7.2 V, VO = 3.3 V, IO = 300 mA, EN = VI, TA = -40C to 85C (unless otherwise noted) PARAMETER Fixed output voltage tolerance (1) TEST CONDITIONS MIN -3% 3% TPS62054 VI = 2.7 V to 10 V, 0 mA< IO< 600 mA -3% 3% TPS62056 VI = 3.75 V to 10 V, 0 mA< IO< 600 mA -3% 3% 700 1000 k VO = 3.3 V, VI = 5 V to 10 V, IO = 600 mA 5.2 mV/V Load regulation VI = 7.2 V; IO = 10 mA to 600 mA 0.0045 %/mA VI = 5 V; VO = 3.3 V; IO = 300 mA 93% VI = 3.6 V; VO = 2.5 V; IO = 200 mA 93% Efficiency 100% Minimum ton time for main switch Shutdown temperature Start-up time 4 1300 UNIT Line regulation Duty cycle range for main switches (1) MAX VI = 2.7 V to 10 V, 0 mA< IO< 600 mA Resistance of internal voltage divider for fixed-voltage versions TYP TPS62052 IO = 200 mA, VI = 5 V, Vo = 3.3 V, Co = 22 F, L = 10 H 100 ns 145 C 1 ms The worst case rDS(on) of the PMOS in 100% mode for an input voltage of 3.3 V is 0.75 . This value can be used to determine the minimum input voltage if the output current is less than 600 mA with the TPS62056. Copyright (c) 2002-2011, Texas Instruments Incorporated TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com PIN ASSIGNMENTS DGS PACKAGE (TOP VIEW) VIN LBO GND PG FB 1 10 2 9 3 8 4 7 5 6 PGND SW EN SYNC LBI Pin Functions PIN NAME NO. I/O DESCRIPTION EN 8 I Enable. A logic high enables the converter, logic low forces the device into shutdown mode, reducing the supply current to less than 2 A. FB 5 I Feedback pin for the fixed output voltage option. For the adjustable version, an external resistive divider is connected to this pin. The internal voltage divider is disabled for the adjustable version. GND 3 I Ground LBO 2 O Open drain low battery output. Logic low signal indicates a low battery voltage. LBI 6 I Low battery input PG 4 O Power good comparator output. This is an open-drain output. A pullup resistor should be connected between PG and VOUT. The output floats when the output voltage is greater than 95% of the nominal value. PGND 10 I Power ground. Connect all power grounds to this pin. SW 9 O Connect the inductor to this pin. This pin is the switch pin and connected to the drain of the internal power MOSFETS. SYNC 7 I Input for synchronization to the external clock signal. This input can be connected to an external clock or pulled to GND or VI. When an external clock signal is applied, the device synchronizes to this external clock and the device operates in fixed PWM mode. When the pin is pulled to either GND or VI, the internal oscillator is used and the logic level determines if the device operates in fixed PWM or PWM/PFM mode.SYNC = HIGH: Low-noise mode enabled, fixed frequency PWM operation is forcedSYNC = LOW (GND): Power-save mode enabled, PFM/PWM mode enabled. VIN 1 I Supply voltage input Copyright (c) 2002-2011, Texas Instruments Incorporated 5 TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com FUNCTIONAL BLOCK DIAGRAM VI Current Limit Comparator + Undervoltage Lockout Bias Supply - REF SYNC + Soft Start I(AVG) Comparator REF - V I 850 kHz Oscillator V(COMP) P-Channel Power MOSFET Comparator + Saw Tooth Generator S R - Driver Shoot-Through Logic Control Logic Comparator High Comparator Low Comparator High2 SW N-Channel Power MOSFET Load Comparator + SKIP Comparator PG - Error Amp Comparator High + LBO Compensation Comparator Low Comparator Low2 VREF = 0.5 V - R1 - + _ R2 See Note + 1.21 V EN FB LBI PGND GND NOTE: For the adjustable versions (TPS62050, TPS62051), the internal feedback driver is disabled and the FB pin is directly connected to the GM amplifier. 6 Copyright (c) 2002-2011, Texas Instruments Incorporated TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com PARAMETER MEASUREMENT INFORMATION All graphs were generated using the circuit as shown unless otherwise noted. For output voltages other than 5 V, the fixed voltage versions are used. The resistors R1, R2, and the feedforward capacitor (Cff) are removed and the feedback pin is directly connected to the output. WE PD 744 777 10 VI 1 R5 130 k Ci = 10 F TDK C3216X5R1A106M VIN SW EN FB 5 8 TPS62050 6 R6 100 k 9 L1 = 10 H 4 LBI PG 7 R3 1M VO = 5 V R4 1M C(ff) = 6.8 pF R1 = 820 k Co = 22 F 2 SYNC GND 3 LBO R2 = 91 k Taiyo Yuden JMK316BJ226ML PGND 10 Quiescent Current Measurements and Efficiency Were Taken With: R5 = Open, R4 = Open, LBI Connected to GND. Figure 1. Standard Circuit for Adjustable Version Copyright (c) 2002-2011, Texas Instruments Incorporated 7 TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com TYPICAL CHARACTERISTICS Table 1. TABLE OF GRAPHS FIGURE Efficiency vs load current 1-8 Switching frequency vs temperature 9 Output voltage ripple in SKIP mode 10 Output voltage ripple in PWM mode 11 Line transient response in PWM mode 12 Load transient 13 V(switch) and IL (inductor current) in skip mode 14 Start-up timing 15 TPS62050 EFFICIENCY vs LOAD CURRENT TPS62052 EFFICIENCY vs LOAD CURRENT 100 90 VI = 6.5 V Efficiency - % 40 VI = 10 V 30 SYNC = L VO = 5 V TA = 25C 10 0.1 1 60 40 VI = 7.2 V 10 100 SYNC = L VO = 1.5 V TA = 25C VI = 10 V 10 0 0.01 1k VI = 10 V 0.1 1 10 100 SYNC = L VO = 1.8 V TA = 25C 10 0 0.01 1k 0.1 1 10 100 Figure 4. TPS62056 EFFICIENCY vs LOAD CURRENT TPS62050 EFFICIENCY vs LOAD CURRENT TPS62052 EFFICIENCY vs LOAD CURRENT 100 VI = 5.5 V 90 Efficiency - % 70 VI = 7.2 V 50 VI = 10 V 30 70 VI = 7.2 V VI = 8.4 V VI = 10 V 40 SYNC = L VO = 3.3 V TA = 25C 10 1 10 IL - Load Current - mA Figure 5. 100 SYNC = H VO = 5 V TA = 25C 20 10 1k 0 0.01 VI = 5 V 60 VI = 7.2 V 50 40 VI = 10 V 30 30 20 VI = 3.3 V 80 60 50 VI = 2.7 V 90 VI = 6.5 V 80 VI = 5 V 70 1k IL - Load Current - mA Figure 3. 80 0.1 40 20 100 0 0.01 VI = 7.2 V Figure 2. VI = 3.5 V 40 VI = 5 V 50 IL - Load Current - mA 100 60 VI = 3.3 V 60 30 20 IL - Load Current - mA Efficiency - % VI = 5 V 50 30 20 0 0.01 70 VI = 3.3 V Efficiency - % Efficiency - % VI = 8.4 V VI = 2.7 V 80 70 60 50 90 80 VI = 7.2 V 70 VI = 2.7 V Efficiency - % 80 8 100 100 VI = 5.5 V 90 90 TPS62054 EFFICIENCY vs LOAD CURRENT 0.1 1 10 IL - Load Current - mA Figure 6. 100 SYNC = H VO = 1.5 V TA = 25C 20 10 1k 0 0.01 0.1 1 10 100 1k IL - Load Current - mA Figure 7. Copyright (c) 2002-2011, Texas Instruments Incorporated TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com TPS62054 EFFICIENCY vs LOAD CURRENT TPS62056 EFFICIENCY vs LOAD CURRENT 100 VI = 2.7 V 90 VI = 3.3 V 80 80 VI = 5 V 60 VI = 7.2 V 50 40 VI = 10 V VI = 7.2 V 60 50 40 VI = 10 V 30 30 SYNC = H VO = 1.8 V TA = 25C 20 10 0 0.01 0.1 1 10 100 SYNC = H VO = 3.3 V TA = 25C 20 10 0 0.01 1k 0.1 1 2.7 V 890 VI = 5 V 70 Efficiency - % 70 900 VI = 3.5 V 90 10 100 3.6 V 880 Switching Frequency - kHz 100 870 5V 860 850 7.2 V 840 830 820 810 800 1k -40 -20 0 20 40 60 80 TA - Free-Air Temperature - C IL - Load Current - mA IL - Load Current - mA 100 Figure 8. Figure 9. Figure 10. OUTPUT VOLTAGE RIPPLE IN SKIP MODE OUTPUT VOLTAGE RIPPLE IN PWM MODE LINE TRANSIENT RESPONSE IN PWM MODE VI = 7.2 V VO = 3.3 V IO = 800 mA Output Voltage IO = 20 mA Voltage at SW Pin VO 10 mV/div 2 V/div 2 V/div 10 mV/div VI = 4.5 V to 5.5 V to 4.5 V 500 mv/div VI = 7.2 V, VO = 3.3 V 10 mV/div Output Voltage Voltage at SW Pin 10 s/div 1 s/div 1 s/div Figure 11. Figure 12. Figure 13. LOAD TRANSIENT V(SWITCH) AND IL (INDUCTOR CURRENT) IN SKIP MODE START-UP TIMING VI = 5 V VO = 3.3 V Voltage at SW Pin EN 5 V/div 50 mV/div Output Voltage 5 V/div Efficiency - % SWITCHING FREQUENCY vs FREE-AIR TEMPERATURE VI = 5 V IO = 100 mA VO 50 s/div 5 s/div Figure 14. Figure 15. Copyright (c) 2002-2011, Texas Instruments Incorporated II VI = 5 V RL = 2.7 100 mA/div 100 mA/div Load Step = 60 mA to 540 mA 500 mA/div 1 V/div Inductor Current 200 s/div Figure 16. 9 TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com APPLICATION INFORMATION Operation The TPS6205x is a synchronous step-down converter that operates with a 850-kHz fixed frequency pulse width modulation (PWM) at moderate to heavy load currents and enters the power-save mode at light load current. During PWM operation the converter uses a unique fast response voltage mode control scheme with input voltage feed forward to achieve good line and load regulation with the use of small ceramic input and output capacitors. At the beginning of each clock cycle initiated by the clock signal (S), the P-channel MOSFET switch is turned on and the inductor current ramps up until the voltage-comparator trips and the control logic turns the switch off. Also the switch is turned off by the current limit comparator in case the current limit of the P-channel switch is exceeded. After the dead time preventing current shoot through, the N-channel MOSFET rectifier is turned on and the inductor current ramps down. The next cycle is initiated by the clock signal again, turning off the N-channel rectifier and turning on the P-channel switch. The error amplifier as well as the input voltage determines the rise time of the saw tooth generator; therefore, any change in input voltage or output voltage directly controls the duty cycle of the converter giving a very good line and load transient regulation. Constant Frequency Mode Operation (SYNC = HIGH) In the constant frequency mode, the output voltage is regulated by varying the duty cycle of the PWM signal in the range of 100% to 10%. Connecting the SYNC pin to a voltage greater than 1.5 V forces the converter to operate permanently in the PWM mode even at light or no load currents. The advantage is the converter operates with a fixed switching frequency that allows simple filtering of the switching frequency for noise sensitive applications. In this mode, the efficiency is lower compared to the power-save mode during light loads (see Figure 17). The N-MOSFET of the devices stays on even when the current into the output drops to zero. This prevents the device from going into discontinuous mode. The device transfers unused energy back to the input. Therefore, there is no ringing at the output that usually occurs in the discontinuous mode. The duty cycle range in constant frequency mode is 100% to 10%. It is possible to switch from forced PWM mode to the power-save mode during operation by pulling the SYNC pin low. The flexible configuration of the SYNC pin during operation of the device allows efficient power management by adjusting the operation of the TPS6205x to the specific system requirements. Power-Save Mode Operation (SYNC = LOW) As the load current decreases, the converter enters the power-save mode operation. During power-save mode the converter operates with reduced switching frequency in PFM and with a minimum quiescent current to maintain high efficiency. Whenever the average output current goes below the skip threshold, the converter enters the power-save mode. The average current depends on the input voltage. It is 100 mA at low input voltages and up to 200 mA with maximum input voltage. The average output current must be below the threshold for at least 32 clock cycles (tcy) to enter the power-save mode. During the power-save mode the output voltage is monitored with a comparator. When the output voltage falls below the comp low threshold set to 0.8% above VO nominal, the P-channel switch turns on. The P-channel switch turns off as the peak switch current of typically 200 mA is reached. The N-channel rectifier turns on and the inductor current ramps down. As the inductor current approaches zero, the N-channel rectifier is turned off and the switch is turned on starting the next pulse. When the output voltage can not be reached with a single pulse, the device continues to switch with its normal operating frequency, until the comparator detects the output voltage to be 1.6% above the nominal output voltage. The converter wakes up again when the output voltage falls below the comp low threshold. This control method reduces the quiescent current to typically to 12 A and the switching frequency to a minimum achieving the highest converter efficiency. Having these skip current thresholds 0.8% and 1.6% above the nominal output voltage gives a lower absolute voltage drop during a load transient as anticipated with a standard converter operating in this mode. Feedforward Capacitor The feedforward capacitor, C(ff) shown in Figure 21, improves the performance in SKIP mode. The comparator is faster, therefore, there is less voltage ripple at the output in SKIP mode. Use the values listed in Table 2. Larger values decrease stability in fixed frequency PWM mode. If the TPS6205x is only operated in fixed frequency PWM mode, the feedforward capacitor is not needed. 10 Copyright (c) 2002-2011, Texas Instruments Incorporated TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com 1.6% 0.8% VO, nominal -1.6% t Figure 17. Power-Save Mode Output Voltage Thresholds The converter enters the fixed frequency PWM mode again as soon as the output voltage falls below the comp low 2 threshold set to 1.6% below VO, nominal. Soft-Start The TPS6205x has an internal soft-start circuit that limits the inrush current during start-up. This prevents possible voltage drops of the input voltage if a battery or a high impedance power source is connected to the input of the TPS6205x. The soft-start is implemented as a digital circuit increasing the switch current in steps of 200 mA, 400 mA, 800 mA and then the typical switch current limit of 1.2 A. Therefore the start-up time mainly depends on the output capacitor and load current. Typical start-up time with a 22-F output capacitor and a 200-mA load current is 1 ms. 100% Duty Cycle Low Dropout Operation The TPS6205x offers the lowest possible input to output voltage difference while still maintaining operation with the use of the 100% duty cycle mode. In this mode, the P-channel switch is constantly turned on. This is particularly useful in battery powered applications to achieve longest operation time by taking full advantage of the whole battery voltage range, i.e. The minimum input voltage to maintain regulation depends on the load current and output voltage and can be calculated as: V I(min) + V (max) ) I (max) O O rDS(on)(max) ) RL IO(max) = Maximum output current plus inductor ripple current rDS(on)(max) = Maximum P-Channel switch rDS(on) RL = DC resistance of the inductor VO(max) = Nominal output voltage plus maximum output voltage tolerance Enable and Overtemperature Protection Logic low on EN forces the TPS6205x into shutdown. In shutdown, the power switch, drivers, voltage reference, oscillator, and all other functions are turned off. The supply current is reduced to less than 2 A in the shutdown mode. When the device is in thermal shutdown, the bandgap is forced to stay on even if the device is set into shutdown by pulling EN to GND. As soon as the temperature drops below the threshold, the device automatically starts again. If an output voltage is present when the device is disabled, which could be an external voltage source or super cap, the reverse leakage current is specified under electrical characteristics. Pulling the enable pin high starts up the TPS6205x with the soft-start as described under the paragraph soft-start. If the EN pin is connected to any voltage other than VI or GND, an increased leakage current of typically 10 A and up to 20 A can occur. Copyright (c) 2002-2011, Texas Instruments Incorporated 11 TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com VIN VIN 0 A for VEN < 0.6 V Typically 0.3 A to 5 Afor VEN < 4 V 5V EN Vt = 0.7 V Enable to Internal Circuitry Figure 18. Internal Circuit of the ENABLE Pin The EN pin can be used in a pushbutton configuration as shown in Figure 19. The external resistor to GND must be capable of sinking 0.3 A with a minimum voltage drop of 1.3 V to keep the system enabled when both switches are open. When the ON-button is pressed, the device is enabled and the current through the external resistor keeps the voltage level high to ensure that the device stays on when the ON-button is released. When the OFF-button is pressed, the device is switched off and the current through the external resistor is zero. The device therefore stays off even when the OFF-button is released. VIN TPS6205x ON EN OFF 0.3 A, min R >1.3 V/0.3 A Figure 19. Pushbutton Configuration for the EN-Pin Undervoltage Lockout The undervoltage lockout circuit prevents the device from misoperation at low input voltages. It prevents the converter from turning on the switch or rectifier MOSFET under undefined conditions. Synchronization If no clock signal is applied, the converter operates with a typical switching frequency of 850 kHz. It is possible to synchronize the converter to an external clock within a frequency range from 600 kHz to 1200 kHz. The device automatically detects the rising edge of the first clock and synchronizes to the external clock. If the clock signal is stopped, the converter automatically switches back to the internal clock and continues operation. The switchover is initiated if no rising edge on the SYNC pin is detected for a duration of four clock cycles. Therefore, the maximum delay time can be 8.3 s if the internal clock has its minimum frequency of 600 kHz. During this time, there is no clock signal available. The device stops switching until the internal circuitry is switched to the internal clock source. When the device is switched between internal synchronization and external synchronization during operation, the output voltage may show transient over/undershoot during switchover. The voltage transients are minimized by using 850 kHz as an initial external frequency, and changing the frequency slowly (>1 ms) to the value desired. The voltage drop at the output when the device is switched from external synchronization to internal synchronization can be reduced by increasing the output capacitor value. If the device is synchronized to an external clock, the power-save mode is disabled and the device stays in forced PWM mode. 12 Copyright (c) 2002-2011, Texas Instruments Incorporated TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com Connecting the SYNC pin to the GND pin enables the power-save mode. The converter operates in the PWM mode at moderate to heavy loads and in the PFM mode during light loads maintaining high efficiency over a wide load current range. Power Good Comparator The power good (PG) comparator has an open drain output capable of sinking typically 1 mA. The PG function is only active when the device is enabled (EN = high). When the device is disabled (EN = low), the PG pin is pulled to GND. The PG output is only valid after a 250 s delay after the device is enabled and the supply voltage is greater than 2.7 V. Power good is low during the first 250 s after shutdown and in shutdown. The PG pin floats high when the output voltage exceeds typically 98.5% of its nominal value. Leave the PG pin unconnected, or connect to GND when not used. Low-Battery Detector (Standard Version) The low-battery output (LBO) is an open drain type which goes low when the voltage at the low battery input (LBI) falls below the trip point of 1.21 V 1.5%. The voltage at which the low-battery warning is issued is adjusted with a resistive divider as shown in Figure 21. The sum of the resistors R1 and R2 is recommended to be in the 100-k to 1-M range for high efficiency at low output current. An external pullup resistor at LBO can either be connected to OUT, or any other voltage rail in the voltage range of 0 V to 6 V. During start-up, the LBO output signal is invalid for the first 500 s. LBO is high impedance when the device is disabled. If the low-battery comparator function is not used, connect LBI to ground. The low-battery detector is disabled when the device is disabled. Leave the LBO pin unconnected, or connect to GND when not used. ENABLE/Low-Battery Detector (Enhanced Version) TPS62051 Only The TPS62051 offers an enhanced LBI functionality to provide a precise, user programmable undervoltage shutdown. No additional supply voltage supervisor (SVS) is needed to provide this function. When the enable (EN) pin is pulled high, only the internal bandgap voltage reference is switched on to provide a reference source for the LBI comparator. As long as the voltage at LBI is less than the LBI trip point, all other internal circuits are shut down, reducing the supply current to 5 A. As soon as input voltage at LBI rises above the LBI trip point of 1.21 V, the device is completely enabled and starts switching. VIN ENABLE Bandgap Enable to Internal Circuitry LBI LBI Comparator LBO Figure 20. Block Diagram of ENABLE/LBI Functionality for TPS62051 The logic level of the LBO pin is not defined for the first 500 s after EN is pulled high. When the enhanced LBI is used to supervise the battery voltage and shut down the TPS62051 at low input voltages, the battery voltage rises again when the current drops to zero. The implemented hysteresis on the LBI pin may not be sufficient for all types of batteries. Figure 21 shows how an additional external hysteresis can be implemented. Copyright (c) 2002-2011, Texas Instruments Incorporated 13 TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com 1 8 VIN SW EN FB L1 = 10 H VO = 2.5 V / 600 mA 5 R3 R4 R1 C(ff) = 6.8 pF TPS62051 R5 6 Ci = 10 F 1 Cell Li-lon 9 PG 4 LBI 7 SYNC R6 GND 3 LBO R2 2 Co = 22 F PGND 10 R7 Figure 21. Enhanced LBI With Increased Hysteresis A MATHCAD(R) file to calculate R7 can be downloaded from the product folder on the TI web. No Load Operation If the converter operates in the forced PWM mode and there is no load connected to the output, the converter regulates the output voltage by allowing the inductor current to reverse for a short period of time. STANDARD CIRCUIT FOR ADJUSTABLE VERSION WE PD 744 777 10 VI 1 R5 130 k Ci = 10 F VIN SW EN FB 5 8 R6 100 k R3 1M VO = 5 V R4 1M C(ff) = 6.8 pF TPS62050 6 TDK C3216X5R1A106M 9 L1 = 10 H R1 = 820 k 4 LBI PG 7 Co = 22 F 2 SYNC GND 3 LBO Taiyo Yuden JMK316BJ226ML R2 = 91 k PGND 10 Quiescent Current Measurements and Efficiency Were Taken With: R5 = Open, R4 = Open, LBI Connected to GND. V 14 O +V FB R1 ) R2 R2 V R1 + R2 O -R2 V FB V FB + 0.5V Copyright (c) 2002-2011, Texas Instruments Incorporated TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com Table 2. Values NOMINAL OUTPUT VOLTAGE EQUATION POSSIBLE RESISTOR COMBINATION TYPICAL FEEDBACK CAPACITOR 0.7 V R1 = 0.4 x R2 R1 = 270 k, R2 = 680 k C(ff) = 22 pF 1.2 V R1 = 1.4 x R2 R1 = 510 k, R2 = 360 k (1.21 V) C(ff) = 6.8 pF 1.5 V R1 = 2 x R2 R1 = 300 k, R2 = 150 k (1.50 V) C(ff) = 6.8 pF 1.8 V R1 = 2.6 x R2 R1 = 390 k, R2 = 150 k (1.80 V) C(ff) = 6.8 pF 2.5 V R1 = 4 x R2 R1 = 680 k, R2 = 169 k (2.51 V) C(ff) = 6.8 pF 3.3 V R1 = 5.6 x R2 R1 = 560 k, R2 = 100 k (3.30 V) C(ff) = 6.8 pF 5V R1 = 9 x R2 R1 = 820 k, R2 = 91 k (5.0 V) C(ff) = 6.8 pF STANDARD CIRCUIT FOR FIXED VOLTAGE VERSION VI = 2.7 V to 10 V 1 R5 VIN SW EN FB 9 L1 = 10 H 5 8 R3 VO = 1.8 V / 600 mA R4 TPS62054 Ci = 10 F 6 4 R6 PG LBI 7 SYNC LBO Co = 22 F 2 PGND GND 3 10 CONVERTER FOR 0.7-V OUTPUT VOLTAGE VI = 2.7 V to 7 V 1 SW VIN R1 = 270 k 8 EN Ci = 10 F 9 L1 = 10 H FB 5 VO = 0.7 V / 600 mA C(ff) = 22 pF TPS62050 6 4 LBI PG 7 R2 = 680 k Co = 47 F 2 SYNC GND 3 LBO PGND 10 The TPS62050 is used to generate output voltages as low as 0.7 V. With such low output voltages, the inductor discharges very slowly. This leads to a high output voltage ripple in power-save mode (SYNC = GND). It is therefore recommended to use a larger output capacitor to keep the output ripple low. With an output capacitor of 47 F, the output voltage ripple is less than 40 mVPP. Copyright (c) 2002-2011, Texas Instruments Incorporated 15 TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com LAYOUT AND BOARD SPACE All capacitors should be soldered as close as possible to the IC. For information on the PCB layout see the user's guideSLVU081. Keep the feedback track as short as possible. Any coupling to the FB pin may cause additional output voltage ripple. INDUCTOR SELECTION A 10-H minimum inductor should be used with the TPS6205x. Values larger than 22 H or smaller than 10 H may cause stability problems due to the internal compensation of the regulator. After choosing the inductor value of typically 10 H, two additional inductor parameter should be considered: the current rating of the inductor and the dc resistance. The dc resistance of the inductance directly influences the efficiency of the converter. Therefore, an inductor with lowest dc resistance should be selected for highest efficiency. In order to avoid saturation of the inductor, the inductor should be rated at least for the maximum output current plus half the inductor ripple current which is calculated as: DI L + V O V 1* O V I L f I L(max) + I (max) ) DIL O 2 f = Switching frequency (850 kHz typical) L = Inductor value IL = Peak-to-peak inductor ripple current IL(max) = Maximum inductor current The highest inductor current occurs at maximum VIN . A more conservative approach is to select the inductor current rating just for the maximum switch current of the TPS6205x which is 1.4 A maximum. See Table 3 for inductors that have been tested for operation with the TPS6205x. Table 3. Inductors MANUFACTURER TYPE INDUCTANCE DC RESISTANCE SATURATION CURRENT TDK SLF7032T100M1R4SLF7032T220M96SLF7045T100M1R3SLF7045T100MR90 10 H 20% 22 H 20% 10 H 20% 22 H 20% 53 m 20% 110 m 20% 36 m 20% 61 m 20% 1.4 A 0.96 A 1.3 A 0.9 A CDR74B 10 H 70 m 1.65 A CDR74B 22 H 130 m 1.12 A CDH74 10 H 49 m 1.8 A CDH74 22 H 110 m 1.23 A CDR63B 10 H 140 m 1A CDRH4D28 10 H 128 m 1A CDRH5D28 10 H 48 m 1.3 A CDRH5D18 10 H 92 m 1.2 A DT3316P-153 15 H 60 m 1.8 A DT3316P-223 22 H 84 m 1.5 A WE-PD 744 778 10 10 H 72 m 1.68 A 1.84 A Sumida Coilcraft Wuerth 16 WE-PD 744 777 10 10 H 49 m WE-PD 744 778 122 22 H 190 m 1.07A WE-PD 744 777 122 22 H 110 m 1.23 A Copyright (c) 2002-2011, Texas Instruments Incorporated TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com OUTPUT CAPACITOR SELECTION The output capacitor should have a minimum value of 22F. For best performance, a low ESR ceramic output capacitor is needed. For completeness, the RMS ripple current is calculated as: I RMS(Co) +V O V 1- O V I L f 1 3 2 The overall output ripple voltage is the sum of the voltage spike caused by the output capacitor ESR plus the voltage ripple caused by charge and discharging the output capacitor: DV O +V O V 1* O V I L f 8 1 Co f )R ESR The highest output voltage ripple occurs at the highest input voltage VI. INPUT CAPACITOR SELECTION Because the buck converter has a pulsating input current, a low ESR input capacitor is required for best input voltage filtering and minimizing the interference with other circuits caused by high input voltage spikes. The input capacitor should have a minimum value of 10 F and can be increased without any limit for better input voltage filtering. The input capacitor should be rated for the maximum input ripple current calculated as: V I + I (max) RMS O O V I V 1* O V I The worst case RMS ripple current occurs at D = 0.5 and is calculated as: IRMS = IO/2. Ceramic capacitors have a good performance because of their low ESR value and they are less sensitive to voltage transients compared to tantalum capacitors. Place the input capacitor as close as possible to the input pin of the IC for best performance. Table 4. Capacitors MANUFACTURER Taiyo Yuden Kemet TDK (1) PART NUMBER SIZE VOLTAGE CAPACITANCE TYPE JMK212BJ106MG 0805 6.3 V 10 F Ceramic JMK316BJ106ML 1206 6.3 V 10 F Ceramic JMK316BJ226ML 1206 6.3 V 22 F Ceramic LMK316BJ475ML 1206 10 V 4.7 F (1) Ceramic (1) Ceramic 4.7 F EMK316BJ475ML 1206 16 V EMK325BJ106KN-T 1210 16 V 10 F Ceramic C1206C106M9PAC 1206 6.3 V 10 F Ceramic C2012X5R0J106M 0805 6.3 V 10 F Ceramic C3216X5R0J226M 1206 6.3 V 22 F Ceramic C3216X5R1A106M 1206 10 V 10 F Ceramic Connect two in parallel. Copyright (c) 2002-2011, Texas Instruments Incorporated 17 TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com Table 5. Capacitor Manufacturers 18 MANUFACTURER CAPACITOR TYPE INTERNET Taiyo Yuden X7R/X5R ceramic www.t-yuden.com TDK X7R/X5R ceramic www.component.tdk.com Vishay X7R/X5R ceramic www.vishay.com Kemet X7R/X5R ceramic www.kemet.com Copyright (c) 2002-2011, Texas Instruments Incorporated TPS62052, TPS62054 TPS62056, TPS62050, TPS62051 SLVS432E - SEPTEMBER 2002 - REVISED JUNE 2011 www.ti.com REVISION HISTORY Note: Page numbers of current version may differ from previous versions. Changes from Revision D (October 2003) to Revision E Page * Changed to Revision E, June 2011 ...................................................................................................................................... 1 * Changed formatting. ............................................................................................................................................................. 1 * Changed "goes active high" to "floats" in Terminal Functions table, row PG, description. .................................................. 5 * Changed "becomes active" to "floats" in last paragraph of Power Good Comparator section. .......................................... 13 Copyright (c) 2002-2011, Texas Instruments Incorporated 19 PACKAGE OPTION ADDENDUM www.ti.com 2-Jun-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp TPS62050DGS ACTIVE MSOP DGS 10 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TPS62050DGSG4 ACTIVE MSOP DGS 10 80 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TPS62050DGSR ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TPS62050DGSRG4 ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAUAGLevel-1-260C-UNLIM TPS62051DGS ACTIVE MSOP DGS 10 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62051DGSG4 ACTIVE MSOP DGS 10 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62051DGSR ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62051DGSRG4 ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62052DGS ACTIVE MSOP DGS 10 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62052DGSG4 ACTIVE MSOP DGS 10 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62052DGSR ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62052DGSRG4 ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62054DGS ACTIVE MSOP DGS 10 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62054DGSG4 ACTIVE MSOP DGS 10 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62054DGSR ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62054DGSRG4 ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62056DGS ACTIVE MSOP DGS 10 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 (3) Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 2-Jun-2011 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp TPS62056DGSG4 ACTIVE MSOP DGS 10 80 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62056DGSR ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS62056DGSRG4 ACTIVE MSOP DGS 10 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM (3) Samples (Requires Login) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 23-Aug-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPS62050DGSR MSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TPS62051DGSR MSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TPS62052DGSR MSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TPS62054DGSR MSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 TPS62056DGSR MSOP DGS 10 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 23-Aug-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS62050DGSR MSOP DGS 10 2500 367.0 367.0 35.0 TPS62051DGSR MSOP DGS 10 2500 367.0 367.0 35.0 TPS62052DGSR MSOP DGS 10 2500 367.0 367.0 35.0 TPS62054DGSR MSOP DGS 10 2500 367.0 367.0 35.0 TPS62056DGSR MSOP DGS 10 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated