X7R Dielectric General Specifications X7R formulations are called "temperature stable" ceramics and fall into EIA Class II materials. X7R is the most popular of these intermediate dielectric constant materials. Its temperature variation of capacitance is within 15% from -55C to +125C. This capacitance change is non-linear. Capacitance for X7R varies under the influence of electrical operating conditions such as voltage and frequency. X7R dielectric chip usage covers the broad spectrum of industrial applications where known changes in capacitance due to applied voltages are acceptable. PART NUMBER (see page 2 for complete part number explanation) 0805 5 C 103 M A T Size (L" x W") Voltage 4V = 4 6.3V = 6 10V = Z 16V = Y 25V = 3 50V = 5 100V = 1 200V = 2 500V = 7 Dielectric X7R = C Capacitance Code (In pF) 2 Sig. Digits + Number of Zeros Capacitance Tolerance J = 5%* K = 10% M = 20% Failure Rate A = Not Applicable 2 A Terminations T = Plated Ni and Sn 7 = Gold Plated* Z= FLEXITERM(R)** Packaging 2 = 7" Reel 4 = 13" Reel 7 = Bulk Cass. 9 = Bulk Special Code A = Std. Product *Optional termination Contact Factory For Multiples *1F only **See FLEXITERM(R) X7R section X7R Dielectric Typical Temperature Coefficient Capacitance vs. Frequency +30 10 +20 % Capacitance 0 -5 -10 -15 -20 0 20 40 60 0 -10 -20 -30 1KHz -25 -60 -40 -20 +10 80 100 120 140 Temperature C 10 KHz 100 KHz 10 1206 0805 1210 1,000 pF Impedance, Impedance, 10,000 pF 1.00 0.10 Frequency, MHz 16 100 0 0 20 40 1000 1.0 0.1 1 10 80 100 120 Variation of Impedance with Chip Size Impedance vs. Frequency 100,000 pF - X7R 10 1206 0805 1210 1.0 0.1 .01 .01 60 Temperature C Variation of Impedance with Chip Size Impedance vs. Frequency 10,000 pF - X7R 10.00 100 10 MHz 1,000 Frequency Variation of Impedance with Cap Value Impedance vs. Frequency 1,000 pF vs. 10,000 pF - X7R 0805 0.01 10 1 MHz Insulation Resistance vs Temperature 10,000 Impedance, % Cap Change 5 Insulation Resistance (Ohm-Farads) NOTE: Contact factory for availability of Termination and Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values. 100 Frequency, MHz 1,000 1 10 100 Frequency, MHz 1,000 X7R Dielectric Specifications and Test Methods Parameter/Test Operating Temperature Range Capacitance Insulation Resistance X7R Specification Limits -55C to +125C Within specified tolerance 2.5% for 50V DC rating 3.0% for 25V DC rating 3.5% for 16V DC rating 5.0% for 10V DC rating 100,000M or 1000M - F, whichever is less Dielectric Strength No breakdown or visual defects Dissipation Factor Resistance to Flexure Stresses Appearance Capacitance Variation Dissipation Factor Insulation Resistance Solderability Resistance to Solder Heat Thermal Shock Load Life Load Humidity Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength Appearance Capacitance Variation Dissipation Factor Insulation Resistance Dielectric Strength No defects 12% Measuring Conditions Temperature Cycle Chamber Freq.: 1.0 kHz 10% Voltage: 1.0Vrms .2V For Cap > 10 F, 0.5Vrms @ 120Hz Charge device with rated voltage for 120 5 secs @ room temp/humidity Charge device with 300% of rated voltage for 1-5 seconds, w/charge and discharge current limited to 50 mA (max) Note: Charge device with 150% of rated voltage for 500V devices. Deflection: 2mm Test Time: 30 seconds 1mm/sec Meets Initial Values (As Above) Initial Value x 0.3 95% of each terminal should be covered with fresh solder No defects, <25% leaching of either end terminal 90 mm Dip device in eutectic solder at 230 5C for 5.0 0.5 seconds 7.5% Meets Initial Values (As Above) Dip device in eutectic solder at 260C for 60 seconds. Store at room temperature for 24 2 hours before measuring electrical properties. Meets Initial Values (As Above) Meets Initial Values (As Above) No visual defects Step 1: -55C 2 30 3 minutes 7.5% Step 2: Room Temp 3 minutes Meets Initial Values (As Above) Step 3: +125C 2 30 3 minutes Meets Initial Values (As Above) Step 4: Room Temp 3 minutes Meets Initial Values (As Above) Repeat for 5 cycles and measure after 24 2 hours at room temperature No visual defects 12.5% Initial Value x 2.0 (See Above) Initial Value x 0.3 (See Above) Meets Initial Values (As Above) No visual defects 12.5% Charge device with 1.5 rated voltage ( 10V) in test chamber set at 125C 2C for 1000 hours (+48, -0) Remove from test chamber and stabilize at room temperature for 24 2 hours before measuring. Store in a test chamber set at 85C 2C/ 85% 5% relative humidity for 1000 hours (+48, -0) with rated voltage applied. Initial Value x 2.0 (See Above) Initial Value x 0.3 (See Above) Remove from chamber and stabilize at room temperature and humidity for 24 2 hours before measuring. Meets Initial Values (As Above) 17 X7R Dielectric Capacitance Range PREFERRED SIZES ARE SHADED SIZE 0201 0402 0603 0805 1206 Soldering Packaging Reflow Only All Paper Reflow/Wave All Paper Reflow/Wave All Paper Reflow/Wave Paper/Embossed Reflow/Wave Paper/Embossed 0.60 0.03 (0.024 0.001) 0.30 0.03 (0.011 0.001) 0.15 0.05 (0.006 0.002) 10 16 25 A A A A A A A A A A A A A A A A A A A A A A A A 1.00 0.10 (0.040 0.004) 0.50 0.10 (0.020 0.004) 0.25 0.15 (0.010 0.006) 16 25 50 1.60 0.15 (0.063 0.006) 0.81 0.15 (0.032 0.006) 0.35 0.15 (0.014 0.006) 16 25 50 10 2.01 0.20 (0.079 0.008) 1.25 0.20 (0.049 0.008) 0.50 0.25 (0.020 0.010) 16 25 50 3.20 0.20 (0.126 0.008) 1.60 0.20 (0.063 0.008) 0.50 0.25 (0.020 0.010) 16 25 50 100 J J J J J J J J J J J J J J J J J J N N N N J J J J J J J J J J J J J J J J J J N N N N (L) Length (W) Width (t) Terminal Cap (pF) Cap (F mm (in.) mm (in.) mm (in.) WVDC 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 0.010 0.015 0.022 0.033 0.047 0.068 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 10 22 47 100 WVDC SIZE Letter Max. Thickness A 0.33 (0.013) C G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G 100 200 G G G G G G G G G G G G G G 6.3 J* J* J* J* J* J J J J J J J J J J J J J J J J J N N N N N J J J J J J J J J J J J J J J J N N N N 100 200 J J J J J J J J J J J J N N N N N N N N J J J J J J J J J J J N 6.3 P* P* P* P* 10 J J J J J J J J J J J J J J J M M M P Q J J J J J J J J J J J J J J J M M M Q Q J J J J J J J J J J J J J J M M Q Q Q Q Q* Q* Q* Q* Q* 10 16 25 200 J J J J J J J J J J J J J J P P Q Q J J J J J J J J J J J M Q Q Q Q Q Q J J J J J J M M M M P P 50 100 200 500 K K K K M M M M P P Q* 10 16 25 16 0201 C 0.56 (0.022) 25 50 6.3 10 0402 E 0.71 (0.028) PAPER *Optional Specifications - Contact factory 18 10 C C C C C C C C C C C C C C C C C 6.3 G 0.90 (0.035) 16 25 50 100 200 6.3 0603 J 0.94 (0.037) K 1.02 (0.040) 10 16 25 50 100 200 6.3 0805 M 1.27 (0.050) N 1.40 (0.055) P Q 1.52 1.78 (0.060) (0.070) EMBOSSED 1206 X 2.29 (0.090) Y 2.54 (0.100) Z 2.79 (0.110) 500 X7R Dielectric Capacitance Range PREFERRED SIZES ARE SHADED 1210 1812 1825 2220 2225 Reflow Only Paper/Embossed Reflow Only All Embossed Reflow Only All Embossed Reflow Only All Embossed Reflow Only All Embossed 3.20 0.20 (0.126 0.008) 2.50 0.20 (0.098 0.008) 0.50 0.25 (0.020 0.010) 25 50 100 4.50 0.30 (0.177 0.012) 3.20 0.20 (0.126 0.008) 0.61 0.36 (0.024 0.014) 100 200 4.50 0.30 (0.177 0.012) 6.40 0.40 (0.252 0.016) 0.61 0.36 (0.024 0.014) 50 100 5.70 0.40 (0.225 0.016) 5.00 0.40 (0.197 0.016) 0.64 0.39 (0.025 0.015) 50 100 5.72 0.25 (0.225 0.010) 6.35 0.25 (0.250 0.010) 0.64 0.39 (0.025 0.015) 50 100 16 500 50 25 200 L J J J J J J J J J J J J J J J M M N N X X X Z Z* J J J J J J J J J J J J J J J M M N N X X X Z Z* J J J J J J J J J J J J J J J M P P Z Z Z Z Z* 10 16 25 J J J J J J J J J J J J J J J M X X Z Z Z Z J J J J J J J J J J J J M P Q Q X Z Z Z J J J J J J J J J J M M Z Z M M M M M M P Q Q K K K K K K K K K K K M M Z Z Z Z W T C 0.56 (0.022) K K K K K K K K K M P Q X Z Z K K K K K K K P P X K P P X Z Z Z M M M M M M M M M M M M M M M M M M M M M M M M M P P X X X X X X X X X X X X X X X X X Z t X X X X X X X X X X X X X X X Z Z X X X X X X X X X X X M M M M M M M M M M M M M M M 100 200 50 P P P P P P P P P P P P P X Z 50 100 200 500 50 1210 A 0.33 (0.013) 500 SIZE Letter Max. Thickness 200 Cap (F 10 Cap (pF) (t) Terminal (W) Width mm (in.) mm (in.) mm (in.) WVDC 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 0.010 0.015 0.022 0.033 0.047 0.068 0.10 0.15 0.22 0.33 0.47 0.68 1.0 1.5 2.2 3.3 4.7 10 22 47 100 WVDC (L) Length SIZE Soldering Packaging E 0.71 (0.028) PAPER G 0.90 (0.035) 100 200 1812 J 0.94 (0.037) K 1.02 (0.040) M 1.27 (0.050) N 1.40 (0.055) 500 50 100 25 1825 P Q 1.52 1.78 (0.060) (0.070) EMBOSSED 50 2220 X 2.29 (0.090) Y 2.54 (0.100) 100 2225 Z 2.79 (0.110) *Optional Specifications - Contact factory 19