© Semiconductor Components Industries, LLC, 2012
October, 2012 − Rev. 14
1Publication Order Number:
MC74HC1G08/D
MC74HC1G08
Single 2-Input AND Gate
The MC74HC1G08 is a high speed CMOS 2−input AND gate
fabricated with silicon gate CMOS technology.
The internal circuit is composed of multiple stages, including a
buffer output which provides high noise immunity and stable output.
The MC74HC1G08 output drive current is 1/2 compared to
MC74HC series.
Features
•High Speed: tPD = 7 ns (Typ) at VCC = 5 V
•Low Power Dissipation: ICC = 1 mA (Max) at TA = 25°C
•High Noise Immunity
•Balanced Propagation Delays (tpLH = tpHL)
•Symmetrical Output Impedance (IOH = IOL = 2 mA)
•Chip Complexity: FET = 44
•NLV Prefix for Automotive and Other Applications Requiring
Unique Site and Control Change Requirements; AEC−Q100
Qualified and PPAP Capable
•These Devices are Pb−Free / Halogen−Free and are RoHS Compliant
Figure 1. Pinout
Figure 2. Logic Symbol
IN A
IN B OUT Y
&
VCC
IN B
IN A
OUT YGND
1
2
34
5
L
L
H
H
L
H
L
H
FUNCTION TABLE
Inputs Output
AB
L
L
L
H
Y
See detailed ordering and shipping information in the
package dimensions section on page 4 of this data sheet.
ORDERING INFORMATION
PIN ASSIGNMENT
1
2
3 GND
IN B
IN A
4
5V
CC
OUT Y
http://onsemi.com
MARKING
DIAGRAMS
H2 = Device Code
M = Date Code*
G= Pb−Free Package
SC−88A / SOT−353 / SC−70
DF SUFFIX
CASE 419A
TSOP−5 / SOT−23 / SC−59
DT SUFFIX
CASE 483
H2 M G
G
1
5
H2 M G
G
M
1
5
(Note: Microdot may be in either location)
*Date Code orientation and/or position may vary
depending upon manufacturing location.
MC74HC1G08
http://onsemi.com
2
MAXIMUM RATINGS
Symbol Parameter Value Unit
VCC DC Supply Voltage *0.5 to )7.0 V
VIN DC Input Voltage *0.5 to VCC )0.5 V
VOUT DC Output Voltage *0.5 to VCC )0.5 V
IIK DC Input Diode Current $20 mA
IOK DC Output Diode Current $20 mA
IOUT DC Output Sink Current $12.5 mA
ICC DC Supply Current per Supply Pin $25 mA
TSTG Storage Temperature Range *65 to )150 °C
TLLead Temperature, 1 mm from Case for 10 Seconds 260 °C
TJJunction Temperature Under Bias )150 °C
qJA Thermal Resistance SC70−5/SC−88A/SOT−353 (Note 1)
SOT23−5/TSOP−5/SC59−5
350
230
°C/W
PDPower Dissipation in Still Air at 85°CSC70−5/SC−88A/SOT−353
SOT23−5/TSOP−5/SC59−5
150
200
mW
MSL Moisture Sensitivity Level 1
FRFlammability Rating Oxygen Index: 28 to 34 UL 94 V−0 @ 0.125 in
VESD ESD Withstand Voltage Human Body Model (Note 2)
Machine Model (Note 3)
Charged Device Model (Note 4)
u2000
u200
N/A
V
ILATCHUP Latchup Performance Above VCC and Below GND at 125°C (Note 5) $500 mA
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Measured with minimum pad spacing on an FR4 board, using 10 mm−by−1 inch, 20 ounce copper trace with no air flow.
2. Tested to EIA/JESD22−A114−A.
3. Tested to EIA/JESD22−A115−A.
4. Tested to JESD22−C101−A.
5. Tested to EIA/JESD78.
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter Min Max Unit
VCC DC Supply Voltage 2.0 6.0 V
VIN DC Input Voltage 0.0 VCC V
VOUT DC Output Voltage 0.0 VCC V
TAOperating Temperature Range *55 )125 °C
tr , tfInput Rise and Fall Time VCC = 2.0 V
VCC = 3.0 V
VCC = 4.5 V
VCC = 6.0 V
0
0
0
0
1000
600
500
400
ns
DEVICE JUNCTION TEMPERATURE VERSUS
TIME TO 0.1% BOND FAILURES
Junction
Temperature °CTime, Hours Time, Years
80 1,032,200 117.8
90 419,300 47.9
100 178,700 20.4
110 79,600 9.4
120 37,000 4.2
130 17,800 2.0
140 8,900 1.0
1
1 10 100 1000
FAILURE RATE OF PLASTIC = CERAMIC
UNTIL INTERMETALLICS OCCUR
Figure 3. Failure Rate vs. Time Junction Temperature
NORMALIZED FAILURE RATE
TIME, YEARS
TJ = 130°C
TJ = 120°C
TJ = 110°C
TJ = 100°C
TJ = 90°C
TJ = 80°C
MC74HC1G08
http://onsemi.com
3
DC ELECTRICAL CHARACTERISTICS
VCC TA = 255C TA v 855C*555C v TA v 1255C
Symbol Parameter Test Conditions (V) Min Typ Max Min Max Min Max Unit
VIH Minimum High−Level
Input Voltage
2.0
3.0
4.5
6.0
1.5
2.1
3.15
4.20
1.5
2.1
3.15
4.20
1.5
2.1
3.15
4.20
V
VIL Maximum Low−Level
Input Voltage
2.0
3.0
4.5
6.0
0.5
0.9
1.35
1.80
0.5
0.9
1.35
1.80
0.5
0.9
1.35
1.80
V
VOH Minimum High−Level
Output Voltage
VIN = VIH or VIL
VIN = VIH or VIL
IOH = −20 mA
2.0
3.0
4.5
6.0
1.9
2.9
4.4
5.9
2.0
3.0
4.5
6.0
1.9
2.9
4.4
5.9
1.9
2.9
4.4
5.9
V
VIN = VIH or VIL
IOH = −2 mA
IOH = −2.6 mA
4.5
6.0
4.18
5.68
4.31
5.80
4.13
5.63
4.08
5.58
VOL Maximum Low−Level
Output Voltage
VIN = VIH or VIL
VIN = VIH or VIL
IOL = 20 mA
2.0
3.0
4.5
6.0
0.0
0.0
0.0
0.0
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
0.1
V
VIN = VIH or VIL
IOL = 2 mA
IOL = 2.6 mA
4.5
6.0
0.17
0.18
0.26
0.26
0.33
0.33
0.40
0.40
IIN Maximum Input
Leakage Current
VIN = 6.0 V or GND 6.0 $0.1 $1.0 $1.0 mA
ICC Maximum Quiescent
Supply Current
VIN = VCC or GND 6.0 1.0 10 40 mA
AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 6.0 ns)
TA = 255C TA v 855C*555C v TA v 1255C
Symbol Parameter Test Conditions Min Typ Max Min Max Min Max Unit
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
tPLH,
tPHL
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
Maximum Propagation
Delay, Input A or B to Y
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
VCC = 5.0 V CL = 15 pF
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
3.5
ÎÎ
ÎÎ
15
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
20
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
25
ÎÎ
ÎÎ
ns
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
VCC = 2.0 V CL = 50 pF
VCC = 3.0 V
VCC = 4.5 V
VCC = 6.0 V
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
20
11
8
7
ÎÎ
ÎÎ
ÎÎ
ÎÎ
100
27
20
17
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
125
35
25
21
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
155
90
35
26
ÎÎ
ÎÎ
ÎÎ
ÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
tTLH,
tTHL
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
Output Transition Time
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
VCC = 5.0 V CL = 15 pF
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
3
ÎÎ
ÎÎ
10
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
15
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
20
ÎÎ
ÎÎ
ns
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
VCC = 2.0 V CL = 50 pF
VCC = 3.0 V
VCC = 4.5 V
VCC = 6.0 V
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
25
16
11
9
ÎÎ
ÎÎ
ÎÎ
125
35
25
21
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
155
45
31
26
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
200
60
38
32
ÎÎ
ÎÎ
ÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
CIN
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎ
Maximum Input
Capacitance
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎÎÎÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
5
ÎÎ
ÎÎ
ÎÎ
10
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎ
10
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
10
ÎÎ
ÎÎ
ÎÎ
pF
Typical @ 255C, VCC = 5.0 V
CPD Power Dissipation Capacitance (Note 6) 10 pF
6. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load.
Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no−load dynamic
power consumption; PD = CPD VCC2 fin + ICC VCC.
MC74HC1G08
http://onsemi.com
4
*Includes all probe and jig capacitance.
A 1−MHz square input wave is recommended for propagation delay tests.
Figure 4. Switching Waveforms
Figure 5. Test Circuit
CL*
INPUT
VCC
OUTPUT
VCC
GND
50%
50%
INPUT
A or B
OUTPUT Y
tPHL
tPLH
90%
10%
90%
10%
tTLH tTHL
trtf
ORDERING INFORMATION
Device Package Shipping†
MC74HC1G08DFT1G SC70−5/SC−88A/SOT−353
(Pb−Free)
3000 / Tape & Reel
MC74HC1G08DFT2G SC70−5/SC−88A/SOT−353
(Pb−Free)
MC74HC1G08DTT1G SOT23−5/TSOP−5/SC59−5
(Pb−Free)
NLVHC1G08DFT1G* SC70−5/SC−88A/SOT−353
(Pb−Free)
NLVHC1G08DFT2G* SC70−5/SC−88A/SOT−353
(Pb−Free)
NLVHC1G08DTT1G* SOT23−5/TSOP−5/SC59−5
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*NLV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AEC−Q100 Qualified and PPAP
Capable.
MC74HC1G08
http://onsemi.com
5
PACKAGE DIMENSIONS
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. 419A−01 OBSOLETE. NEW STANDARD
419A−02.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
DIM
A
MIN MAX MIN MAX
MILLIMETERS
1.80 2.200.071 0.087
INCHES
B1.15 1.350.045 0.053
C0.80 1.100.031 0.043
D0.10 0.300.004 0.012
G0.65 BSC0.026 BSC
H--- 0.10---0.004
J0.10 0.250.004 0.010
K0.10 0.300.004 0.012
N0.20 REF0.008 REF
S2.00 2.200.079 0.087
B0.2 (0.008) MM
12 3
45
A
G
S
D 5 PL
H
C
N
J
K
−B−
SC−88A (SC−70−5/SOT−353)
CASE 419A−02
ISSUE K
MC74HC1G08
http://onsemi.com
6
PACKAGE DIMENSIONS
TSOP−5
CASE 483−02
ISSUE H
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. MAXIMUM LEAD THICKNESS INCLUDES
LEAD FINISH THICKNESS. MINIMUM LEAD
THICKNESS IS THE MINIMUM THICKNESS
OF BASE MATERIAL.
4. DIMENSIONS A AND B DO NOT INCLUDE
MOLD FLASH, PROTRUSIONS, OR GATE
BURRS.
5. OPTIONAL CONSTRUCTION: AN
ADDITIONAL TRIMMED LEAD IS ALLOWED
IN THIS LOCATION. TRIMMED LEAD NOT TO
EXTEND MORE THAN 0.2 FROM BODY.
DIM MIN MAX
MILLIMETERS
A3.00 BSC
B1.50 BSC
C0.90 1.10
D0.25 0.50
G0.95 BSC
H0.01 0.10
J0.10 0.26
K0.20 0.60
L1.25 1.55
M0 10
S2.50 3.00
123
54 S
A
G
L
B
D
H
C
J
__
0.7
0.028
1.0
0.039
ǒmm
inchesǓ
SCALE 10:1
0.95
0.037
2.4
0.094
1.9
0.074
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
SOLDERING FOOTPRINT*
0.20
5X
CAB
T0.10
2X
2X T0.20
NOTE 5
T
SEATING
PLANE
0.05
K
M
DETAIL Z
DETAIL Z
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
MC74HC1G08/D
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your loca
l
Sales Representative
