19-1613; Rev 3; 3/02 Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References Features The MAX6100-MAX6107 are low-cost, low-dropout (LDO), micropower voltage references. These three-terminal references are available with output voltage options of 1.25V, 1.8V, 2.048V, 2.5V, 3V, 4.096V, 4.5V, and 5V. They feature a proprietary curvature-correction circuit and laser-trimmed, thin-film resistors that result in a low temperature coefficient of 75ppm/C (max) and an initial accuracy of 0.4% (max). These devices are specified over the extended temperature range (-40C to +85C). Ultra-Small 3-Pin SOT23 Package These series-mode voltage references draw only 90A of supply current and can source 5mA and sink 2mA of load current. Unlike conventional shunt-mode (two-terminal) references that waste supply current and require an external resistor, these devices offer a supply current that is virtually independent of the supply voltage (with only a 4A/V variation with supply voltage) and do not require an external resistor. Additionally, these internally compensated devices do not require an external compensation capacitor and are stable with load capacitance. Eliminating the external compensation capacitor saves valuable board area in space-critical applications. Lowdropout voltage and supply independent, ultra-low supply current make these devices ideal for battery-operated, high-performance, low-voltage systems. Low 75ppm/C Temperature Coefficient The MAX6100-MAX6107 are available in tiny 3-pin SOT23 packages. Applications Portable Battery-Powered Systems Notebook Computers PDAs, GPSs, DMMs Cellular Phones Hard-Disk Drives IN REFERENCE OUT MAX6100-MAX6107 * *CAPACITORS ARE OPTIONAL. Stable with Capacitive Loads Load Regulation (2mA Sink): 8mV/mA (max) Load Regulation (5mA Source): 0.9mV/mA (max) 0.4% (max) Initial Accuracy 125A (max) Quiescent Supply Current 50mV Dropout at 1mA Load Current Ordering Information PART TEMP RANGE PINPACKAGE TOP MARK MAX6100EUR-T -40C to +85C 3 SOT23-3 FZID MAX6101EUR-T -40C to +85C 3 SOT23-3 FZGT MAX6102EUR-T -40C to +85C 3 SOT23-3 FZGU MAX6103EUR-T -40C to +85C 3 SOT23-3 FZGV MAX6104EUR-T -40C to +85C 3 SOT23-3 FZGW MAX6105EUR-T -40C to +85C 3 SOT23-3 FZGX MAX6106EUR-T -40C to +85C 3 SOT23-3 FZJR MAX6107EUR-T -40C to +85C 3 SOT23-3 FZMV Selector Guide +SUPPLY INPUT (SEE SELECTOR GUIDE) GND No Output Capacitor Required Note: There is a minimum order increment of 2500 pieces for SOT23 packages. Typical Operating Circuit OUT Low Cost PART OUTPUT VOLTAGE (V) INPUT VOLTAGE RANGE (V) MAX6100 1.800 2.5 to 12.6 MAX6101 1.250 2.5 to 12.6 MAX6102 2.500 (VOUT + 200mV) to 12.6 MAX6103 3.000 (VOUT + 200mV) to 12.6 MAX6104 4.096 (VOUT + 200mV) to 12.6 MAX6105 5.000 (VOUT + 200mV) to 12.6 MAX6106 2.048 2.5 to 12.6 MAX6107 4.5 (VOUT + 200mV) to 12.6 1F* Pin Configuration appears at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX6100-MAX6107 General Description MAX6100-MAX6107 Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References ABSOLUTE MAXIMUM RATINGS (Voltages Referenced to GND) IN .........................................................................-0.3V to +13.5V OUT .............................................................-0.3V to (VIN + 0.3V) Output Short-Circuit to GND or IN (VIN < 6V) ............Continuous Output Short-Circuit to GND or IN (VIN 6V) .........................60s Continuous Power Dissipation (TA = +70C) 3-Pin SOT23 (derate 4.0mW/C above +70C)............320mW Operating Temperature Range ...........................-40C to +85C Storage Temperature Range .............................-65C to +150C Lead Temperature (soldering, 10s) .................................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS--MAX6101, VOUT = 1.25V (VIN = 5V, IOUT = 0, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER Output Voltage SYMBOL VOUT Output Voltage Temperature Coefficient (Notes 2, 3) TCVOUT Line Regulation VOUT/ VIN Load Regulation VOUT/ IOUT OUT Short-Circuit Current ISC Long-Term Stability VOUT/ time Output Voltage Hysteresis (Note 4) VOUT/ cycle CONDITIONS TA = +25C MIN TYP MAX UNITS 1.245 1.250 1.255 V 0C to +70C 65 -40C to +85C 75 2.5V VIN 12.6V 90 Sourcing: 0 IOUT 5mA 0.9 Sinking: -2mA IOUT 0 3.0 ppm/C V/V mV/mA Short to GND 110 Short to IN 12 1000hr at +25C 50 ppm/ 1000hr 130 ppm f = 0.1Hz to 10Hz 13 VP-P f = 10Hz to 10kHz 15 VRMS VIN = 5V 100mV, f = 120Hz 86 dB To VOUT = 0.1% of final value, COUT = 50pF 50 s mA DYNAMIC CHARACTERISTICS Noise Voltage Ripple Rejection Turn-On Settling Time INPUT CHARACTERISTICS eOUT VOUT/ VIN tR Supply Voltage Range VIN Quiescent Supply Current IIN Change in Supply Current IIN/VIN 2 Guaranteed by line-regulation test 2.5V VIN 12.6V 2.5 12.6 V 90 125 A 4 8 A/V _______________________________________________________________________________________ Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References (VIN = 5V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C) (Note 1) PARAMETER Output Voltage SYMBOL VOUT Output Voltage Temperature Coefficient (Notes 2, 3) TCVOUT Line Regulation VOUT/ VIN Load Regulation VOUT/ IOUT OUT Short-Circuit Current CONDITIONS TA = +25C MIN TYP MAX UNITS 1.793 1.800 1.807 V 0C to +70C 65 -40C to +85C 75 2.5V VIN 12.6V 200 Sourcing: 0 IOUT 5mA 0.9 Sinking: -2mA IOUT 0 4.0 ppm/C V/V mV/mA Short to GND 110 Short to IN 12 1000hr at +25C 50 ppm/ 1000hr 130 ppm f = 0.1Hz to 10Hz 22 VP-P f = 10Hz to 10kHz 25 VRMS VOUT/ VIN VIN = 5V, 100mV, f = 120Hz 86 dB tR To VOUT = 0.1% of final value, COUT = 50pF 100 s ISC Long-Term Stability VOUT/ time Output Voltage Hysteresis (Note 4) VOUT/ cycle mA DYNAMIC CHARACTERISTICS eOUT Noise Voltage Ripple Rejection Turn-On Settling Time INPUT CHARACTERISTICS Supply Voltage Range VIN Quiescent Supply Current Change in Supply Current IIN IIN/VIN Guaranteed by line-regulation test 2.5V VIN 12.6V 2.5 90 4 12.6 V 125 8 A A/V _______________________________________________________________________________________ 3 MAX6100-MAX6107 ELECTRICAL CHARACTERISTICS--MAX6100, VOUT = 1.8V MAX6100-MAX6107 Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References ELECTRICAL CHARACTERISTICS--MAX6106, VOUT = 2.048V (VIN = 5V, IOUT = 0, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER Output Voltage SYMBOL TYP MAX UNITS 2.040 2.048 2.056 V TCVOUT 65 75 ppm/C Line Regulation VOUT / VIN_ 2.5V VIN 12.6V 200 V/V Load Regulation VOUT/ IOUT Sourcing : 0 IOUT 5mA 0.9 Sinking: -2mA IOUT 0 4.0 OUT Short-Circuit Current Long-Term Stability Output Voltage Hysteresis (Note 4) DYNAMIC CHARACTERISTICS Noise Voltage Ripple Rejection Turn-On Settling Time ISC VOUT/ time VOUT/ cycle TA = +25C MIN 0C to +70C -40C to +85C Output Voltage Temperature Coefficient (Notes 2, 3) VOUT CONDITIONS mV/mA Short to GND 110 Short to IN 12 1000hr at +25C 50 ppm/ 1000hr 130 ppm mA f= 0.1Hz to 10Hz 22 VP-P f= 10Hz to 10kHz 25 VRMS VOUT/ VIN VIN = 5V 100mV, f = 120Hz 86 dB tR To VOUT = 0.1% of final value, COUT = 50pF 100 s eOUT INPUT CHARACTERISTICS Supply Voltage Range VIN Quiescent Supply Current IIN Change in Supply Current IIN / VIN 4 Guaranteed by line-regulation test 2.5 VIN 12.6V 2.5 12.6 V 90 125 A 4 8 A/V _______________________________________________________________________________________ Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References (VIN = 5V, IOUT = 0, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER Output Voltage SYMBOL VOUT Output Voltage Temperature Coefficient (Notes 2, 3) TCVOUT Line Regulation VOUT/ VIN Load Regulation VOUT/ IOUT Dropout Voltage (Note 5) VIN VOUT OUT Short-Circuit Current ISC Long-Term Stability VOUT/ time Output Voltage Hysteresis (Note 4) VOUT/ cycle CONDITIONS TA = +25C MIN TYP MAX UNITS 2.490 2.50 2.510 V 0C to +70C 65 -40C to +85C 75 (VOUT + 0.2V) VIN 12.6V 300 Sourcing: 0 IOUT 5mA 0.9 Sinking: -2mA IOUT 0 5.0 200 ppm/C V/V mV/mA IOUT = 1mA 50 Short to GND 110 Short to IN 12 1000hr at +25C 50 ppm/ 1000hr 130 ppm mV mA DYNAMIC CHARACTERISTICS Noise Voltage eOUT VOUT/ VIN Ripple Rejection Turn-On Settling Time INPUT CHARACTERISTICS tR Supply Voltage Range VIN Quiescent Supply Current IIN Change in Supply Current IIN/VIN f = 0.1Hz to 10Hz 27 VP-P f = 10Hz to 10kHz 30 VRMS VIN = 5V 100mV, f = 120Hz 86 dB To VOUT = 0.1% of final value, COUT = 50pF 115 s Guaranteed by line-regulation test (VOUT + 0.2V) VIN 12.6V VOUT + 0.2 12.6 V 90 125 A 4 8 A/V _______________________________________________________________________________________ 5 MAX6100-MAX6107 ELECTRICAL CHARACTERISTICS--MAX6102, VOUT = 2.50V MAX6100-MAX6107 Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References ELECTRICAL CHARACTERISTICS--MAX6103, VOUT = 3.0V (VIN = 5V, IOUT = 0, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER Output Voltage SYMBOL VOUT Output Voltage Temperature Coefficient (Notes 2, 3) TCVOUT Line Regulation VOUT/ VIN Load Regulation VOUT/ IOUT Dropout Voltage (Note 5) VIN VOUT OUT Short-Circuit Current ISC Long-Term Stability VOUT/ time Output Voltage Hysteresis (Note 4) VOUT/ cycle CONDITIONS TA = +25C MIN TYP MAX UNITS 2.988 3.000 3.012 V 0C to +70C 65 -40C to +85C 75 (VOUT + 0.2V) VIN 12.6V 400 Sourcing: 0 IOUT 5mA 0.9 Sinking: -2mA IOUT 0 6.0 200 ppm/C V/V mV/mA IOUT = 1mA 50 Short to GND 110 Short to IN 12 1000hr at +25C 50 ppm/ 1000hr 130 ppm mV mA DYNAMIC CHARACTERISTICS Noise Voltage Ripple Rejection Turn-On Settling Time INPUT CHARACTERISTICS eOUT VOUT/ VIN tR Supply Voltage Range VIN Quiescent Supply Current IIN Change in Supply Current IIN/VIN 6 f = 0.1Hz to 10Hz 35 VP-P f = 10Hz to 10kHz 40 VRMS VIN = 5V 100mV, f = 120Hz 76 dB To VOUT = 0.1% of final value, COUT = 50pF 115 s Guaranteed by line-regulation test (VOUT + 0.2V) VIN 12.6V VOUT + 0.2 12.6 V 90 125 A 4 8 A/V _______________________________________________________________________________________ Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References (VIN = 5V, IOUT = 0, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER Output Voltage SYMBOL VOUT Output Voltage Temperature Coefficient (Notes 2, 3) TCVOUT Line Regulation VOUT/ VIN Load Regulation VOUT/ IOUT Dropout Voltage (Note 5) VIN VOUT OUT Short-Circuit Current ISC Long-Term Stability VOUT/ time Output Voltage Hysteresis (Note 4) VOUT/ cycle CONDITIONS TA = +25C MIN TYP MAX UNITS 4.080 4.096 4.112 V 0C to +70C 65 -40C to +85C 75 (VOUT + 0.2V) VIN 12.6V 430 Sourcing: 0 IOUT 5mA 0.9 Sinking: -2mA IOUT 0 8.0 200 ppm/C V/V mV/mA IOUT = 1mA 50 Short to GND 110 Short to IN 12 1000hr at +25C 50 ppm/ 1000hr 130 ppm mV mA DYNAMIC CHARACTERISTICS Noise Voltage eOUT VOUT/ VIN Ripple Rejection Turn-On Settling Time INPUT CHARACTERISTICS tR Supply Voltage Range VIN Quiescent Supply Current IIN Change in Supply Current IIN/VIN f = 0.1Hz to 10Hz 50 VP-P f = 10Hz to 10kHz 50 VRMS VIN = 5V 100mV, f = 120Hz 72 dB To VOUT = 0.1% of final value, COUT = 50pF 190 s Guaranteed by line-regulation test (VOUT + 0.2V) VIN 12.6V VOUT + 0.2 12.6 V 90 125 A 4 8 A/V _______________________________________________________________________________________ 7 MAX6100-MAX6107 ELECTRICAL CHARACTERISTICS--MAX6104, VOUT = 4.096V MAX6100-MAX6107 Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References ELECTRICAL CHARACTERISTICS--MAX6107, VOUT = 4.5V (VIN = 5V, IOUT = 0, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER Output Voltage SYMBOL VOUT Output Voltage Temperature Coefficient (Notes 2, 3) TCVOUT Line Regulation VOUT/ VIN Load Regulation VOUT/ IOUT Dropout Voltage (Note 5) VIN VOUT OUT Short-Circuit Current ISC Long-Term Stability VOUT/ time Output Voltage Hysteresis (Note 4) VOUT/ cycle CONDITIONS TA = +25C MIN TYP MAX UNITS 4.482 4.500 4.518 V 0C to +70C 65 -40C to +85C 75 (VOUT + 0.2V) VIN 12.6V 550 Sourcing: 0 IOUT 5mA 0.9 Sinking: -2mA IOUT 0 8.0 200 ppm/C V/V mV/mA IOUT = 1mA 50 Short to GND 110 Short to IN 12 1000hr at +25C 50 ppm/ 1000hr 130 ppm f = 0.1Hz to 10Hz 55 VP-P f = 10Hz to 10kHz 55 VRMS VIN = 5V 100mV, f = 120Hz 70 dB To VOUT = 0.1% of final value, COUT = 50pF 230 s mV mA DYNAMIC CHARACTERISTICS Noise Voltage Ripple Rejection Turn-On Settling Time INPUT CHARACTERISTICS Supply Voltage Range 8 eOUT VOUT/ VIN tR VIN Quiescent Supply Current IIN Change in Supply Current IIN/VIN Guaranteed by line-regulation test (VOUT + 0.2V) VIN 12.6V VOUT + 0.2 12.6 V 90 125 A 4 8 A/V _______________________________________________________________________________________ Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References (VIN = 5.5V, IOUT = 0, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25C.) (Note 1) PARAMETER Output Voltage SYMBOL VOUT Output Voltage Temperature Coefficient (Notes 2, 3) TCVOUT Line Regulation VOUT/ VIN Load Regulation VOUT/ IOUT Dropout Voltage (Note 5) VIN VOUT OUT Short-Circuit Current ISC Long-Term Stability VOUT/ time Output Voltage Hysteresis (Note 4) VOUT/ cycle CONDITIONS TA = +25C MIN TYP MAX UNITS 4.980 5.000 5.020 V 0C to +70C 65 -40C to +85C 75 (VOUT + 0.2V) VIN 12.6V 550 Sourcing: 0 IOUT 5mA 0.9 Sinking: -2mA IOUT 0 10 200 ppm/C V/V mV/mA IOUT = 1mA 50 Short to GND 110 Short to IN 12 1000hr at +25C 50 ppm/ 1000hr 130 ppm mV mA DYNAMIC CHARACTERISTICS Noise Voltage eOUT VOUT/ VIN Ripple Rejection Turn-On Settling Time INPUT CHARACTERISTICS Supply Voltage Range tR VIN Quiescent Supply Current IIN Change in Supply Current IIN/VIN f = 0.1Hz to 10Hz 60 VP-P f = 10Hz to 10kHz 60 VRMS VIN = 6V 100mV, f = 120Hz 65 dB To VOUT = 0.1% of final value, COUT = 50pF 300 s Guaranteed by line-regulation test (VOUT + 0.2V) VIN 12.6V VOUT + 0.2 12.6 V 90 125 A 4 8 A/V Note 1: Devices are 100% production tested at TA = +25C and are guaranteed by design from TA = TMIN to TMAX by correlation to sample units characterized over temperature. Note 2: Temperature coefficient is specified by the "box" method, i.e., the maximum VOUT is divided by the maximum t. Note 3: Not production tested. Guaranteed by design. Note 4: Thermal hysteresis is defined as the change in +25C output voltage before and after temperature cycling of the device from TA = TMIN to TMAX. Note 5: Dropout voltage is the minimum input voltage at which VOUT changes 0.2% from VOUT at VIN = 5.0V (VIN = 5.5V for MAX6105). _______________________________________________________________________________________ 9 MAX6100-MAX6107 ELECTRICAL CHARACTERISTICS--MAX6105, VOUT = 5.000V Typical Operating Characteristics (TA = +25C, unless otherwise noted.) MAX6102 OUTPUT VOLTAGE TEMPERATURE DRIFT 2.493 2.492 2.491 5.000 4.998 4.996 4.994 2.490 2.488 -20 0 20 40 60 80 -40 -20 0 20 40 60 MAX6102 DROPOUT VOLTAGE vs. SOURCE CURRENT 90 VIN = 5.5V VIN = 2.5V 80 MAX6100/07 TOC05 DROPOUT VOLTAGE (mV) MAX6100/07 toc04 VIN = 7.5V 100 250 TA = +85C 200 150 100 6 8 10 12 14 TA = +25C MAX6102 DROPOUT VOLTAGE vs. SINK CURRENT 0 -10 TA = -40C 50 4 INPUT VOLTAGE (V) MAX6101 SUPPLY CURRENT vs. TEMPERATURE VIN = 12.5V 40 2 TEMPERATURE (C) 110 60 0 80 TEMPERATURE (C) 120 SUPPLY CURRENT (A) 3 TYPICAL PARTS TEMPERATURE RISING 4.990 -40 80 20 4.992 DROPOUT VOLTAGE (mV) 3 TYPICAL PARTS TEMPERATURE RISING 2.489 MAX6100/07 TOC03 100 MAX6100/07 TOC06 2.494 120 SUPPLY CURRENT (A) 5.002 OUTPUT VOLTAGE (V) 2.495 OUTPUT VOLTAGE (V) 5.004 MAX6100/07 TOC02 2.496 SUPPLY CURRENT vs. INPUT VOLTAGE MAX6105 OUTPUT VOLTAGE TEMPERATURE DRIFT MAX6100/07 TOC01 2.497 -20 -30 TA = -40C -40 -50 -60 TA = +85C -70 TA = +25C -80 -15 10 35 60 0 85 1 2 3 4 0 5 0.5 1.0 1.5 2.0 TEMPERATURE (C) SOURCE CURRENT (mA) SINK CURRENT (mA) MAX6105 DROPOUT VOLTAGE vs. SOURCE CURRENT MAX6105 DROPOUT VOLTAGE vs. SINK CURRENT MAX6102 LOAD REGULATION TA = +25C 150 TA = -40C 100 -10 -20 -30 TA = -40C -40 -50 -60 TA = +85C -70 50 0 0 1 2 3 4 SOURCE CURRENT (mA) 5 6 TA = +25C 8 7 OUTPUT VOLTAGE CHANGE (mV) 200 MAX6100/07 TOC08 TA = +85C 0 DROPOUT VOLTAGE (mV) MAX6100/07 TOC07 250 6 4 2 1.5 2.0 2.5 TA = -40C 0 -2 1.0 TA = -40C 1 -1 SINK CURRENT (mA) TA = +25C 3 -90 0.5 TA = +85C SOURCE SINK 5 -80 0 2.5 MAX6100/07 TOC09 -40 10 -90 0 70 DROPOUT VOLTAGE (mV) MAX6100-MAX6107 Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References TA = +85C TA = +25C -6 -4 -2 0 2 4 6 LOAD CURRENT (mA) ______________________________________________________________________________________ 8 10 12 Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References MAX6102 LINE REGULATION TA = +25C 2 TA = -40C 1 0.15 TA = -40C 0.10 0.05 TA = +25C 0 TA = +85C -0.05 -0.10 -4 -2 0 2 4 6 8 10 6 8 10 12 INPUT VOLTAGE (V) MAX6102 POWER-SUPPLY REJECTION RATIO vs. FREQUENCY MAX6105 POWER-SUPPLY REJECTION RATIO vs. FREQUENCY 70 60 70 TA = +85C 0.10 0.05 TA = +25C 4 6 8 10 12 14 MAX6101 LINE-TRANSIENT RESPONSE VIN 200mV/div 50 PSRR (dB) 60 50 40 40 30 VOUT 200mV/div 30 20 20 10 10 0.01 0.1 1 10 100 1000 0 0.001 FREQUENCY (kHz) 1 10 100 1000 100s/div MAX6105 LINE-TRANSIENT RESPONSE MAX6100/07 TOC16 VOUT 100mV/div 0.1 FREQUENCY (kHz) MAX6102 LINE-TRANSIENT RESPONSE VIN 200mV/div 0.01 OUTPUT IMPEDANCE vs. FREQUENCY MAX6100/07 TOC17 0 0.001 0.15 14 MAX6100/07 TOC14 80 0.20 INPUT VOLTAGE (V) 80 MAX6100/07 TOC13 90 PSRR (dB) 4 LOAD CURRENT (mA) 100 TA = -40C 0.25 -0.05 2 12 VIN 200mV/div VOUT 5mV/div 800 700 OUTPUT IMPEDANCE () -6 0.30 0 TA = +85C -1 MAX6100/07 TOC12 0.35 MAX6100/07 TOC18 0 TA = -40C TA = +25C 0.20 0.40 MAX6100/07 TOC15 3 MAX6100/07 TOC11 SINK 0.25 OUTPUT VOLTAGE CHANGE (mV) TA = +85C SOURCE 4 OUTPUT VOLTAGE CHANGE (mV) MAX6100/07 TOC10 5 MAX6105 LINE REGULATION OUTPUT VOLTAGE CHANGE (mV) MAX6105 LOAD REGULATION 600 500 400 300 200 100 0 -100 100s/div 100s/div 0.01 0.1 1 10 100 1k 10k 100k 1M FREQUENCY (Hz) ______________________________________________________________________________________ 11 MAX6100-MAX6107 Typical Operating Characteristics (continued) (TA = +25C, unless otherwise noted.) Typical Operating Characteristics (continued) (TA = +25C, unless otherwise noted.) MAX6101 LOAD-TRANSIENT RESPONSE (CLOAD = 0) VOUT 200mV/div MAX6100/07 TOC20 MAX6100/07 TOC19 MAX6102 LOAD-TRANSIENT RESPONSE (CLOAD = 0) VOUT 200mV/div 5mA 4mA IOUT 5mA/div IOUT 5mA/div -2mA -2mA 200s/div 200s/div MAX6105 LOAD-TRANSIENT RESPONSE (CLOAD = 0) VOUT 200mV/div IOUT 5mA/div MAX6100/07 TOC22 MAX6100/07 TOC21 MAX6102 LOAD-TRANSIENT RESPONSE (CLOAD = 1F) VIN 2V/div 5mA -2mA VOUT 50mV/div 200s/div 200s/div MAX6105 LOAD-TRANSIENT RESPONSE (CLOAD = 1F) VIN 5V/div MAX6101 TURN-ON TRANSIENT MAX6100/07 TOC24 MAX6100/07 TOC23 MAX6100-MAX6107 Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References VIN 2V/div VOUT 50mV/div VOUT 500mV/div 100s/div 12 100s/div ______________________________________________________________________________________ Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References MAX6105 TURN-ON TRANSIENT 20V/div MAX6100/07 TOC27 VIN 2V/div MAX6105 0.1Hz TO 10Hz OUTPUT NOISE MAX6100/07 TOC26 MAX6100/07 TOC25 MAX6102 0.1Hz TO 10Hz OUTPUT NOISE 20V/div VOUT 2V/div 100s/div 1s/div Pin Description PIN NAME FUNCTION 1 IN 2 OUT Reference Output 3 GND Ground Input Voltage Applications Information Input Bypassing For the best line-transient performance, decouple the input with a 0.1F ceramic capacitor as shown in the Typical Operating Circuit. Locate the capacitor as close to IN as possible. Where transient performance is less important, no capacitor is necessary. Output/Load Capacitance Devices in the MAX6100 family do not require an output capacitance for frequency stability. They are stable for any capacitive load when sourcing less than 200A. When sourcing greater than 200A, the output may become unstable with capacitive loads between 0.5nF and 50nF. In applications where the load or the supply can experience step changes, an output capacitor reduces the amount of overshoot (undershoot) and improves the circuit's transient response. Many applications do not require an external capacitor, and the MAX6100 family can offer a significant advantage in these applications when board space is critical. 1s/div Supply Current The quiescent supply current of the series-mode MAX6100 family is typically 90A and is virtually independent of the supply voltage, with only an 8A/V (max) variation with supply voltage. Unlike series references, shunt-mode references operate with a series resistor connected to the power supply. The quiescent current of a shunt-mode reference is thus a function of the input voltage. Additionally, shunt-mode references have to be biased at the maximum-expected load current, even if the load current is not present at the time. In the MAX6100 family, the load current is drawn from the input voltage only when required, so supply current is not wasted and efficiency is maximized at all input voltages. This improved efficiency reduces power dissipation and extends battery life. When the supply voltage is below the minimum specified input voltage (as during turn-on), the devices can draw up to 400A beyond the nominal supply current. The input voltage source must be capable of providing this current to ensure reliable turn-on. Output Voltage Hysteresis Output voltage hysteresis is the change of output voltage at TA = +25C before and after the device is cycled over its entire operating temperature range. Hysteresis is caused by differential package stress appearing across the bandgap core transistors. The typical temperature hysteresis value is 130ppm. ______________________________________________________________________________________ 13 MAX6100-MAX6107 Typical Operating Characteristics (continued) (TA = +25C, unless otherwise noted.) Turn-On Time These devices typically turn on and settle to within 0.1% of their final value in 50s to 300s. The turn-on time can increase up to 1.5ms with the device operating at the minimum dropout voltage and the maximum load. Pin Configuration TOP VIEW IN 1 MAX6100-MAX6107 3 GND OUT 2 SOT23 Chip Information TRANSISTOR COUNT: 117 Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) SOTPO3L.EPS MAX6100-MAX6107 Low-Cost, Micropower, Low-Dropout, High-Output-Current, SOT23 Voltage References Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 14 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 2002 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.