CY7C1041CV33 Automotive 4-Mbit (256 K x 16) Static RAM 4-Mbit (256 K x 16) Static RAM Features Functional Description Temperature ranges Automotive-A: -40 C to 85 C Automotive-E: -40 C to 125 C The CY7C1041CV33 Automotive is a high performance CMOS static RAM organized as 262,144 words by 16 bits. Pin and function compatible with CY7C1041BNV33 High speed tAA = 10 ns (Automotive-A) tAA = 12 ns (Automotive-E) Low active power 432 mW (max) 2.0 V data retention Automatic power down when deselected TTL-compatible inputs and outputs Easy memory expansion with CE and OE features Available in Pb-free and non Pb-free 44-pin 400 Mil SOJ, 44-pin TSOP II and 48-ball FBGA packages To write to the device, take Chip Enable (CE) and Write Enable (WE) inputs LOW. If Byte Low Enable (BLE) is LOW, then data from I/O pins (I/O0 through I/O7), is written into the location specified on the address pins (A0 through A17). If Byte High Enable (BHE) is LOW, then data from I/O pins (I/O8 through I/O15) is written into the location specified on the address pins (A0 through A17). To read from the device, take Chip Enable (CE) and Output Enable (OE) LOW while forcing the Write Enable (WE) HIGH. If Byte Low Enable (BLE) is LOW, then data from the memory location specified by the address pins appear on I/O0 to I/O7. If Byte High Enable (BHE) is LOW, then data from memory appears on I/O8 to I/O15. For more information, see the Truth Table on page 10 for a complete description of Read and Write modes. The input and output pins (I/O0 through I/O15) are placed in a high impedance state when the device is deselected (CE HIGH), the outputs are disabled (OE HIGH), the BHE and BLE are disabled (BHE, BLE HIGH), or during a write operation (CE LOW and WE LOW). For best practice recommendations, refer to the Cypress application note AN1064, SRAM System Guidelines. Logic Block Diagram SENSE AMPS A0 A1 A2 A3 A4 A5 A6 A7 A8 ROW DECODER INPUT BUFFER 256K x 16 RAM Array I/O0-I/O7 I/O8-I/O15 * BHE WE CE OE BLE A16 A17 A14 A15 A12 A13 A9 Cypress Semiconductor Corporation Document Number: 001-67307 Rev. ** A10 A11 COLUMN DECODER 198 Champion Court * San Jose, CA 95134-1709 * 408-943-2600 Revised March 11, 2011 [+] Feedback CY7C1041CV33 Automotive Contents Selection Guide ................................................................ 3 Pin Configuration ............................................................. 3 Pin Definitions .................................................................. 4 Maximum Ratings ............................................................. 5 Operating Range ............................................................... 5 Electrical Characteristics ................................................. 5 Capacitance ...................................................................... 6 Thermal Resistance .......................................................... 6 AC Test Loads and Waveforms ....................................... 6 Switching Characteristics ................................................ 7 Switching Waveforms ...................................................... 8 Truth Table ...................................................................... 10 Document Number: 001-67307 Rev. ** Ordering Information ...................................................... 11 Ordering Code Definitions ......................................... 11 Package Diagrams .......................................................... 12 Acronyms ....................................................................... 15 Document Conventions ................................................. 15 Units of Measure ....................................................... 15 Document History Page ................................................. 16 Sales, Solutions, and Legal Information ...................... 17 Worldwide Sales and Design Support ....................... 17 Products .................................................................... 17 PSoC Solutions ......................................................... 17 Page 2 of 17 [+] Feedback CY7C1041CV33 Automotive Selection Guide Description Maximum Access Time -10 -12 -20 Unit 10 12 20 ns 100 - 85 mA Automotive-E - 120 90 mA Automotive-A 10 - 10 mA - 15 15 mA Maximum Operating Current Automotive-A Maximum CMOS Standby Current Automotive-E Pin Configuration Figure 1. 44-pin SOJ/TSOP II (Top View) [1] A0 A1 A2 A3 A4 CE IO0 IO1 IO2 IO3 VCC VSS IO4 IO5 IO6 IO7 WE A5 A6 A7 A8 A9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 A17 A16 A15 OE BHE BLE IO15 IO14 IO13 IO12 VSS VCC IO11 IO10 IO9 IO8 NC A14 A13 A12 A11 A10 Figure 2. 48-ball FBGA Pinout (Top View) [1] 1 2 3 4 5 6 BLE OE A0 A1 A2 NC A IO0 BHE A3 A4 CE IO8 B IO1 IO2 A5 A6 IO10 IO9 C VSS IO3 A17 A7 IO11 VCC D VCC IO4 NC A16 IO12 VSS E IO6 IO5 A14 A15 IO13 IO14 F IO7 NC A12 A13 WE IO15 G NC A8 A9 A10 A11 NC H Note 1. NC pins are not connected on the die. Document Number: 001-67307 Rev. ** Page 3 of 17 [+] Feedback CY7C1041CV33 Automotive Pin Definitions Pin Name SOJ, TSOP Pin Number BGA Pin Number I/O Type A0-A17 1-5, 18-27, 42-44 A3, A4, A5, B3, B4, C3, C4, D4, H2, H3, H4, H5, G3, G4, F3, F4, E4, D3 Input I/O0-I/O15 Description Address Inputs. Used to select one of the address locations. 7-10,13-16, B1, C1, C2, D2, Input or Output Bidirectional Data I/O lines. Used as input or output lines 29-32, 35-38 E2, F2, F1, G1, depending on operation. B6, C6, C5, D5, E5, F5, F6, G6 NC 28 A6, E3, G2, H1, H6 No Connect WE 17 G5 Input or Control Write Enable Input, Active LOW. When selected LOW, a write is conducted. When deselected HIGH, a read is conducted. CE 6 B5 Input or Control Chip Enable Input, Active LOW. When LOW, selects the chip. When HIGH, deselects the chip. BHE, BLE 40, 39 B2, A1 Input or Control Byte Write Select Inputs, Active LOW. BHE controls I/O15 - I/O8, BLE controls I/O7 - I/O0. OE 41 A2 Input or Control Output Enable, Active LOW. Controls the direction of the I/O pins. When LOW, the I/O pins are allowed to behave as outputs. When deasserted HIGH, the I/O pins are tri-stated and act as input data pins. VSS 12, 34 D1, E6 Ground Ground for the Device. Connected to ground of the system. VCC 11, 33 D6, E1 Document Number: 001-67307 Rev. ** No Connects. Not connected to the die. Power Supply Power Supply Inputs to the Device. Page 4 of 17 [+] Feedback CY7C1041CV33 Automotive Maximum Ratings Current into Outputs (LOW)......................................... 20 mA Exceeding maximum ratings may impair the useful life of the device. These user guidelines are not tested. Storage Temperature ............................... -65 C to +150 C Static Discharge Voltage.......................................... > 2001 V (MIL-STD-883, Method 3015) Latch Up Current .................................................... > 200 mA Operating Range Ambient Temperature with Power Applied .......................................... -55 C to +125 C Ambient Temperature (TA) VCC Automotive-A -40 C to +85 C 3.3 V 10% Automotive-E -40 C to +125 C Range Supply Voltage on VCC Relative to GND[2] ...-0.5 V to +4.6 V DC Voltage Applied to Outputs in High Z State[2] .................................. -0.5 V to VCC + 0.5 V DC Input Voltage[2] .............................. -0.5 V to VCC + 0.5 V Electrical Characteristics Over the Operating Range Parameter Description Test Conditions VOH Output HIGH Voltage VCC = Min, IOH = -4.0 mA -10 -12 -20 Unit Min Max Min Max Min Max 2.4 - 2.4 - 2.4 - V VOL Output LOW Voltage VCC = Min, IOL = 8.0 mA - 0.4 - 0.4 - 0.4 V VIH Input HIGH Voltage 2.0 VCC + 0.3 2.0 VCC + 0.3 2.0 VCC + 0.3 V VIL [2] Input LOW Voltage -0.3 0.8 -0.3 0.8 -0.3 0.8 V IIX Input Leakage Current GND < VI < VCC A Output Leakage Current GND < VOUT < VCC, Output disabled VCC Operating Supply Current VCC = Max, f = fMAX = 1/tRC IOZ ICC ISB1 ISB2 Auto-A -1 +1 - - -1 +1 Auto-E - - -20 +20 -20 +20 Auto-A -1 +1 - - -1 +1 Auto-E - - -20 +20 -20 +20 Auto-A - 100 - - - 85 Auto-E - - - 120 - 90 Automatic CE Power Max VCC, CE > VIH, Down Current --TTL VIN > VIH, or VIN < VIL, Inputs f = fMAX Auto-A - 40 - - - 40 Auto-E - - - 45 - 45 Automatic CE Power Max VCC, Down Current -- CE > VCC - 0.3 V, VIN > VCC - 0.3 V, CMOS Inputs or VIN < 0.3 V, f = 0 Auto-A - 10 - - - 10 Auto-E - - - 15 - 15 A mA mA mA Note 2. VIL (min) = -2.0 V and VIH(max) = VCC + 0.5 V for pulse durations of less than 20 ns. Document Number: 001-67307 Rev. ** Page 5 of 17 [+] Feedback CY7C1041CV33 Automotive Capacitance Tested initially and after any design or process changes that may affect these parameters. Parameter Description CIN Input Capacitance COUT Output Capacitance Test Conditions TA = 25 C, f = 1 MHz, VCC = 3.3 V Max Unit 8 pF 8 pF Thermal Resistance Tested initially and after any design or process changes that may affect these parameters. Parameter Description JA Thermal Resistance (Junction to Ambient) JC Thermal Resistance (Junction to Case) Test Conditions SOJ TSOP II FBGA Unit Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA/JESD51 25.99 42.96 38.15 C/W 18.8 10.75 9.15 C/W AC Test Loads and Waveforms Figure 3. AC Test Loads and Waveforms [3] 10-ns devices: 12-, 15-, 20-ns devices: Z = 50 50 * CAPACITIVE LOAD CONSISTS OF ALL COMPONENTS OF THE TEST ENVIRONMENT R 317 3.3 V OUTPUT 30 pF* OUTPUT R2 351 30 pF* 1.5 V (b) (a) High Z characteristics: 3.0 V GND ALL INPUT PULSES 90% 90% 10% 10% Rise Time: 1 V/ns (c) R 317 3.3 V Fall Time: 1 V/ns OUTPUT R2 351 5 pF (d) Note 3. AC characteristics (except High Z) for 10 ns parts are tested using the load conditions shown in Figure 3 (a). All other speeds are tested using the Thevenin load shown in Figure 3 (b). High Z characteristics are tested for all speeds using the test load shown in Figure 3 (d). Document Number: 001-67307 Rev. ** Page 6 of 17 [+] Feedback CY7C1041CV33 Automotive Switching Characteristics Over the Operating Range [4] Parameter -10 Description -12 -20 Min Max Min Max Min Max Unit Read Cycle tpower[5] VCC(Typical) to the First Access 100 - 100 - 100 - s tRC Read Cycle Time 10 - 12 - 20 - ns tAA Address to Data Valid - 10 - 12 - 20 ns tOHA Data Hold from Address Change 3 - 3 - 3 - ns tACE CE LOW to Data Valid - 10 - 12 - 20 ns tDOE OE LOW to Data Valid Auto-A - 5 - 6 - 8 ns Auto-E - - - 7 - 8 tLZOE OE LOW to Low Z[6] 0 - 0 - 0 - ns - 5 - 6 - 8 ns 3 - 3 - 3 - ns tHZOE tLZCE OE HIGH to High CE LOW to Low Z[6, 7] Z[6] Z[6, 7] tHZCE CE HIGH to High - 5 - 6 - 8 ns tPU CE LOW to Power Up 0 - 0 - 0 - ns tPD CE HIGH to Power Down - 10 - 12 - 20 ns tDBE Byte Enable to Data Valid Auto-A - 5 - 6 - 8 ns Auto-E - - - 7 - 8 tLZBE Byte Enable to Low Z 0 - 0 - 0 - ns Byte Disable to High Z - 6 - 6 - 8 ns tHZBE Write Cycle [8, 9] tWC Write Cycle Time 10 - 12 - 20 - ns tSCE CE LOW to Write End 7 - 8 - 10 - ns tAW Address Setup to Write End 7 - 8 - 10 - ns tHA Address Hold from Write End 0 - 0 - 0 - ns tSA Address Setup to Write Start 0 - 0 - 0 - ns tPWE WE Pulse Width 7 - 8 - 10 - ns tSD Data Setup to Write End 5 - 6 - 8 - ns tHD Data Hold from Write End 0 - 0 - 0 - ns Z[6] tLZWE WE HIGH to Low 3 - 3 - 3 - ns tHZWE WE LOW to High Z[6, 7] - 5 - 6 - 8 ns tBW Byte Enable to End of Write 7 - 8 - 10 - ns Notes 4. Test conditions assume signal transition time of 3 ns or less, timing reference levels of 1.5 V, and input pulse levels of 0 to 3.0 V. 5. tPOWER gives the minimum amount of time that the power supply is at typical VCC values until the first memory access is performed. 6. At any temperature and voltage condition, tHZCE is less than tLZCE, tHZBE is less than tLZBE, tHZOE is less than tLZOE, and tHZWE is less than tLZWE for any device. 7. tHZOE, tHZCE, tHZBE, and tHZWE are specified with a load capacitance of 5 pF as in part (d) of Figure 3 on page 6. Transition is measured 500 mV from steady state voltage. 8. The internal write time of the memory is defined by the overlap of CE LOW, WE LOW, and BHE/BLE LOW. CE, WE, and BHE/BLE must be LOW to initiate a write. The transition of these signals terminate the write. The input data setup and hold timing is referenced to the leading edge of the signal that terminates the write. 9. The minimum Write cycle time for Write Cycle No. 3 (WE controlled, OE LOW) is the sum of tHZWE and tSD. Document Number: 001-67307 Rev. ** Page 7 of 17 [+] Feedback CY7C1041CV33 Automotive Switching Waveforms Figure 4. Read Cycle No. 1 (Address Transition Controlled)[10, 11] tRC RC ADDRESS tOHA DATA OUT tAA PREVIOUS DATA VALID DATA VALID Figure 5. Read Cycle No. 2 (OE Controlled)[11, 12] ADDRESS tRC CE tACE OE tHZOE tDOE tLZOE BHE, BLE tHZCE tDBE tLZBE DATA OUT HIGH IMPEDANCE tLZCE VCC SUPPLY CURRENT tHZBE DATA VALID HIGH IMPEDANCE tPD tPU 50% 50% ICC ISB Notes 10. Device is continuously selected. OE, CE, BHE, and/or BLE = VIL. 11. WE is HIGH for read cycle. 12. Address valid prior to or coincident with CE transition LOW. Document Number: 001-67307 Rev. ** Page 8 of 17 [+] Feedback CY7C1041CV33 Automotive Switching Waveforms (continued) Figure 6. Write Cycle No. 1 (CE Controlled)[13, 14] tWC ADDRESS tSA tSCE CE tAW tHA tPWE WE t BW BHE, BLE tSD tHD DATA IO Figure 7. Write Cycle No. 2 (BLE or BHE Controlled) tWC ADDRESS BHE, BLE tSA tBW tAW tHA tPWE WE tSCE CE tSD tHD DATA IO Notes 13. Data IO is high impedance if OE, BHE, and/or BLE = VIH. 14. If CE goes HIGH simultaneously with WE going HIGH, the output remains in a high impedance state. Document Number: 001-67307 Rev. ** Page 9 of 17 [+] Feedback CY7C1041CV33 Automotive Switching Waveforms (continued) Figure 8. Write Cycle No. 3 (WE Controlled, OE LOW) tWC ADDRESS tSCE CE tAW tHA tSA tPWE WE tBW BHE, BLE tHZWE tSD tHD DATA IO tLZWE Truth Table CE OE WE BLE BHE H X X X X High Z High Z Power Down Standby (ISB) L L H L L Data Out Data Out Read - All Bits Active (ICC) L X L I/O0 - I/O7 I/O8 - I/O15 Mode Power L H Data Out High Z Read - Lower Bits Only Active (ICC) H L High Z Data Out Read - Upper Bits Only Active (ICC) L L Data In Data In Write - All Bits Active (ICC) L H Data In High Z Write - Lower Bits Only Active (ICC) H L High Z Data In Write - Upper Bits Only Active (ICC) L H H X X High Z High Z Selected, Outputs Disabled Active (ICC) L X X H H High Z High Z Selected, Outputs Disabled Active (ICC) Document Number: 001-67307 Rev. ** Page 10 of 17 [+] Feedback CY7C1041CV33 Automotive Ordering Information Cypress offers other versions of this type of product in many different configurations and features. The below table contains only the list of parts that are currently available.For a complete listing of all options, visit the Cypress website at www.cypress.com and refer to the product summary page at http://www.cypress.com/products or contact your local sales representative. Cypress maintains a worldwide network of offices, solution centers, manufacturer's representatives and distributors. To find the office closest to you, visit us at http://www.cypress.com/go/datasheet/offices. Speed (ns) 10 12 20 Ordering Code CY7C1041CV33-10BAXA Package Diagram Package Type 51-85106 48-ball FBGA (Pb-free) CY7C1041CV33-10ZSXA 51-85087 44-pin TSOP II (Pb-free) CY7C1041CV33-12BAXE 51-85106 48-ball FBGA (Pb-free) CY7C1041CV33-12ZSXE 51-85087 44-pin TSOP II (Pb-free) CY7C1041CV33-20ZSXA 51-85087 44-pin TSOP II (Pb-free) CY7C1041CV33-20VXE 44-pin (400-mil) Molded SOJ (Pb-free) CY7C1041CV33-20ZSXE 44-pin TSOP II (Pb-free) Operating Range Automotive-A Automotive-E Automotive-A Automotive-E Please contact your local Cypress sales representative for availability of these parts Ordering Code Definitions CY 7C 1 04 1 C V33 - XX XX X X Temperature Range: X = A or E A = Automotive; E = Automotive Extended X = Pb-free; X Absent = Leaded Package Type: XX = BA or ZS or V BA = 48-ball FBGA ZS = 44-pin TSOP II V = 44-pin (400-mil) Molded SOJ Speed Grade: XX = 10 ns or 12 ns or 20 ns V33 = 3.0 V to 3.6 V Process Technology:C 150 nm Data width: x 16-bits 4-Mbit density Fast Asynchronous SRAM Marketing Code: 7C = SRAMs Company ID: CY = Cypress Document Number: 001-67307 Rev. ** Page 11 of 17 [+] Feedback CY7C1041CV33 Automotive Package Diagrams Figure 9. 44-pin (400 Mil) Molded SOJ, 51-85082 51-85082 *C Document Number: 001-67307 Rev. ** Page 12 of 17 [+] Feedback CY7C1041CV33 Automotive Package Diagrams (continued) Figure 10. 44-pin Thin Small Outline Package Type II, 51-85087 51-85087 *C Document Number: 001-67307 Rev. ** Page 13 of 17 [+] Feedback CY7C1041CV33 Automotive Package Diagrams (continued) Figure 11. 48-ball FBGA (7 x 8.5 x 1.2 mm), 51-85106 51-85106 *F Document Number: 001-67307 Rev. ** Page 14 of 17 [+] Feedback CY7C1041CV33 Automotive Acronyms Document Conventions Acronym Description Units of Measure CE Chip Enable CMOS complementary metal oxide semiconductor ohms FBGA fine-pitch ball grid array ns nano seconds I/O input/output V Volts OE Output Enable s micro seconds PLL phase locked loop A micro Amperes SOJ Small Outline J-lead mA milli Amperes SRAM static random access memory mm milli meter TSOP thin small outline package ms milli seconds TTL transistor-transistor logic MHz Mega Hertz WE Write Enable pF pico Farad % percent mW milli Watts W Watts C degree Celcius Document Number: 001-67307 Rev. ** Symbol Unit of Measure Page 15 of 17 [+] Feedback CY7C1041CV33 Automotive Document History Page Document Title: CY7C1041CV33 Automotive, 4-Mbit (256 K x 16) Static RAM Document Number: 001-67307 REV. ** ECN NO. Issue Date 3187164 03/03/2011 Orig. of Change PRAS Document Number: 001-67307 Rev. ** Description of Change Separation of the automotive datasheet from CY7C1041CV33 spec no. 38-05134 Rev. *K. Further rev of 38-05134 would include only industrial / commercial parts. Page 16 of 17 [+] Feedback CY7C1041CV33 Automotive Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer's representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. Products Automotive Clocks & Buffers Interface Lighting & Power Control PSoC Solutions cypress.com/go/automotive cypress.com/go/clocks psoc.cypress.com/solutions cypress.com/go/interface PSoC 1 | PSoC 3 | PSoC 5 cypress.com/go/powerpsoc cypress.com/go/plc Memory Optical & Image Sensing cypress.com/go/memory cypress.com/go/image PSoC Touch Sensing cypress.com/go/psoc cypress.com/go/touch USB Controllers Wireless/RF cypress.com/go/USB cypress.com/go/wireless (c) Cypress Semiconductor Corporation, 2001-2011. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without the express written permission of Cypress. Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress' product in a life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges. Use may be limited by and subject to the applicable Cypress software license agreement. Document Number: 001-67307 Rev. ** Revised March 11, 2011 Page 17 of 17 All products and company names mentioned in this document may be the trademarks of their respective holders. [+] Feedback