SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 D Controls Boost Preregulator to Near-Unity D D D D D D D D D D D D D, DW, N, and PW PACKAGES (TOP VIEW) Power Factor Limits Line Distortion World Wide Line Operation Over-Voltage Protection Accurate Power Limiting Average Current Mode Control Improved Noise Immunity Improved Feed-Forward Line Regulation Leading Edge Modulation 150-A Typical Start-Up Current Low-Power BiCMOS Operation 12-V to 17-V Operation Frequency Range 6 kHz to 220 kHz GND PKLMT CAOUT CAI MOUT IAC VAOUT VFF 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 DRVOUT VCC CT SS RT VSENSE OVP/EN VREF description The UCCx817/18 family provides all the functions necessary for active power factor corrected preregulators. The controller achieves near unity power factor by shaping the ac input line current waveform to correspond to that of the ac input line voltage. Average current mode control maintains stable, low distortion sinusoidal line current. Designed in Texas Instrument's BiCMOS process, the UCC2817/UCC2818 offers new features such as lower start-up current, lower power dissipation, overvoltage protection, a shunt UVLO detect circuitry, a leading-edge modulation technique to reduce ripple current in the bulk capacitor and an improved, low-offset (2 mV) current amplifier to reduce distortion at light load conditions. block diagram VCC 15 OVP/EN 10 16 V (FOR UCC2817 ONLY) SS VREF 7.5 V 16 DRVOUT 1 GND 2 PKLMT UVLO ENABLE - + 7 VSENSE 11 VFF 9 13 1.9 V VAOUT 7.5 V REFERENCE - 0.33 V VOLTAGE ERROR AMP + - VCC + X / MULT X CURRENT AMP 8.0 V + OVP - - PWM - + S + X2 8 16 V/10 V (UCC2817) 10.5 V/10 V (UCC2818) ZERO POWER PWM LATCH R R OSC CLK MIRROR 2:1 Q CLK IAC 6 MOUT 5 OSCILLATOR - + 4 CAI 12 14 CAOUT RT 3 CT UDG-98182 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. !" # $%&" !# '%() $!" *!"&+ *%$"# $ " #'&$ $!" # '& ",& "&# &-!# #"%&"# #"!*!* .!!"/+ *%$" '$&## 0 *&# " &$&##! )/ $)%*& "&#" 0 !)) '!!&"&#+ Copyright 2006 - 2009, Texas Instruments Incorporated www.ti.com 1 SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 description (continued) UCC2817 offers an on-chip shunt regulator with low start-up current, suitable for applications utilizing a bootstrap supply. UCC2818 is intended for applications with a fixed supply (VCC). Available in the 16-pin D, DW, N and PW packages. absolute maximum ratings over operating free-air temperature (unless otherwise noted) Supply voltage VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Supply current ICC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Gate drive current, continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.2 A Gate drive current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.2 A Input voltage, CAI, MOUT, SS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V Input voltage, PKLMT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 V Input voltage, VSENSE, OVP/EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 V Input current, RT, IAC, PKLMT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 mA Input current, VCC (no switching) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Maximum negative voltage, DRVOUT, PKLMT, MOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V Power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W Junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55C to 150C Storage temperature, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Lead temperature, Tsol (soldering, 10 seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300C Power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 W Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. AVAILABLE OPTIONS PACKAGE DEVICES SOIC (D) PACKAGE SOIC (DW) PACKAGE PDIP (N) PACKAGE TSSOP (PW) PACKAGE TA = TJ Turn-on Threshold 16 V Turn-on Threshold 10.2 V Turn-on Threshold 16 V Turn-on Threshold 10.2 V Turn-on Threshold 16 V Turn-on Threshold 10.2 V Turn-on Threshold 16 V Turn-on Threshold 10.2 V -40C to 85C UCC2817D UCC2818D UCC2817DW UCC2818DW UCC2817N UCC2818N UCC2817PW UCC2818PW 0C to 70C UCC3817D UCC3818D UCC3817DW UCC3818DW UCC3817N UCC3818N UCC3817PW UCC3818PW THERMAL RESISTANCE TABLE PACKAGE jc(C/W) ja(C/W) SOIC-16 (D) 22 SOIC-16 (DW) 26 40 to 70 (1) 89 to 102 (1) PDIP-16 (N) 12 14 (2) 25 to 50 (1) 123 to 147 (2) TSSOP-16 (PW) NOTES: (1) Specified ja (junction to ambient) is for devices mounted to 5-inch2 FR4 PC board with one ounce copper where noted. When resistance range is given, lower values are for 5 inch2 aluminum PC board. Test PWB was 0.062 inch thick and typically used 0.635-mm trace widths for power packages and 1.3-mm trace widths for non-power packages with a 100-mil x 100-mil probe land area at the end of each trace. (2). Modeled data. If value range given for ja, lower value is for 3x3 inch. 1 oz internal copper ground plane, higher value is for 1x1-inch. ground plane. All model data assumes only one trace for each non-fused lead. 2 www.ti.com SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 electrical characteristics, TA = 0C to 70C for the UCC3817 and TA = -40C to 85C for the UCC2817, TA = TJ, VCC = 12 V, RT = 22 k, CT = 270 pF, (unless otherwise noted) supply current section PARAMETER TEST CONDITIONS Supply current, off VCC = (VCC turn-on threshold -0.3 V) Supply current, on VCC = 12 V, No load on DRVOUT MIN TYP MAX 150 300 UNITS A 2 4 6 mA UVLO section MIN TYP MAX UNITS VCC turn-on threshold (UCCx817) PARAMETER TEST CONDITIONS 15.4 16 16.6 V VCC turn-off threshold (UCCx817) 9.4 9.7 UVLO hysteresis (UCCx817) V 5.8 6.3 15.4 17 17.5 V VCC turn-on threshold (UCCx818) 9.7 10.2 10.8 V VCC turn-off threshold (UCCx818) 9.4 9.7 V UVLO hysteresis (UCCx818) 0.3 0.5 V MIN TYP MAX UNITS 7.387 7.5 7.613 V 7.369 7.5 7.631 V 50 200 nA Maximum shunt voltage (UCCx817) IVCC = 10 mA V voltage amplifier section PARAMETER TEST CONDITIONS Input voltage TA = 0C to 70C TA = -40C to 85C VSENSE bias current Open loop gain VSENSE = VREF, VAOUT = 2 V to 5 V High-level output voltage IL = -150 A IL = 150 A Low-level output voltage VAOUT = 2.5 V 50 90 5.3 5.5 5.6 dB V 0 50 150 mV over voltage protection and enable section PARAMETER TEST CONDITIONS MIN TYP MAX UNITS VREF +0.48 VREF +0.50 VREF +0.52 V Hysteresis 300 500 600 mV Enable threshold 1.7 1.9 2.1 V Enable hysteresis 0.1 0.2 0.3 V MIN TYP MAX -3.5 0 2.5 mV -50 -100 nA 25 100 nA Over voltage reference current amplifier section PARAMETER Input offset voltage Input bias current Input offset current Open loop gain Common-mode rejection ratio High-level output voltage Low-level output voltage Gain bandwidth product TEST CONDITIONS VCM = 0 V, VCM = 0 V, VCAOUT = 3 V VCAOUT = 3 V VCM = 0 V, VCM = 0 V, VCAOUT = 3 V VCAOUT = 2 V to 5 V VCM = 0 V to 1.5 V, IL = -120 A VCAOUT = 3 V IL = 1 mA See Note 1 90 UNITS dB 60 80 5.6 6.5 6.8 0.1 0.2 0.5 2.5 dB V V MHz NOTES: 1. Ensured by design, not production tested. www.ti.com 3 SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 electrical characteristics, TA = 0C to 70C for the UCC3817 and TA = -40C to 85C for the UCC2817, TA = TJ, VCC = 12 V, RT = 22 k, CT = 270 pF, (unless otherwise noted) voltage reference section PARAMETER Input voltage Load regulation Line regulation TEST CONDITIONS TA = 0C to 70C TA = -40C to 85C IREF = 1 mA to 2 mA VCC = 10.8 V to 15 V, See Note 2 Short-circuit current VREF = 0 V NOTES: 2. Reference variation for VCC < 10.8 V is shown in Figure 8. MIN TYP MAX UNITS 7.387 7.5 7.613 V 7.369 7.5 7.631 V 0 10 mV 0 10 mV -20 -25 -50 mA UNITS oscillator section PARAMETER MIN TYP MAX 85 100 115 Voltage stability TA = 25C VCC = 10.8 V to 15 V -1 1 Total variation Line, temp 80 120 kHz Initial accuracy TEST CONDITIONS kHz % Ramp peak voltage 4.5 5 5.5 V Ramp amplitude voltage (peak to peak) 3.5 4 4.5 V MIN TYP MAX peak current limit section PARAMETER TEST CONDITIONS UNITS PKLMT reference voltage -15 15 mV PKLMT propagation delay 150 350 500 ns MIN TYP MAX UNITS multiplier section PARAMETER TEST CONDITIONS IMOUT, high line, low power output current, (0C to 85C) IAC = 500 A, VFF = 4.7 V, VAOUT = 1.25 V 0 -6 -20 A IMOUT, high line, low power output current, (-40C to 85C) IAC = 500 A, VFF = 4.7 V, VAOUT = 1.25 V 0 -6 -23 A IMOUT, high line, high power output current IAC = 500 A, VFF = 4.7 V, VAOUT = 5 V -70 -90 -105 A IMOUT, low line, low power output current IAC = 150 A, VFF = 1.4 V, VAOUT = 1.25 V -10 -19 -50 A IMOUT, low line, high power output current IAC = 150 A, VFF = 1.4 V, VAOUT = 5 V -268 -300 -345 A IMOUT, IAC limited output current Gain constant (K) IAC = 150 A, IAC = 300 A, VFF = 1.3 V, VFF = 3 V, VAOUT = 5 V -250 -300 -400 A VAOUT = 2.5 V 0.5 1 1.5 1/V IAC = 150 A, IAC = 500 A, VFF = 1.4 V, VFF = 4.7 V, VAOUT = 0.25 V 0 -2 IMOUT, zero current A VAOUT = 0.25 V 0 -2 A IMOUT, zero current, (0C to 85C) IMOUT, zero current, (-40C to 85C) IAC = 500 A, IAC = 500 A, VFF = 4.7 V, VFF = 4.7 V, VAOUT = 0.5 V 0 -3 A Power limit (IMOUT x VFF) IAC = 150 A, VFF = 1.4 V, VAOUT = 5 V 4 www.ti.com VAOUT = 0.5 V -375 0 -3.5 A -420 -485 W SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 electrical characteristics, TA = 0C to 70C for the UCC3817 and TA = -40C to 85C for the UCC2817, TA = TJ, VCC = 12 V, RT = 22 k, CT = 270 pF, (unless otherwise noted) feed-forward section PARAMETER VFF output current TEST CONDITIONS IAC = 300 A MIN TYP MAX UNITS -140 -150 -160 A MIN TYP MAX UNITS -6 -10 -16 A MIN TYP MAX UNITS 5 12 2 10 25 50 ns 10 50 ns 95 99 % 2 % soft start section PARAMETER TEST CONDITIONS SS charge current gate driver section PARAMETER Pullup resistance TEST CONDITIONS Pulldown resistance IO = -100 mA to -200 mA IO = 100 mA Output rise time CL = 1 nF, RL = 10 , Output fall time CL = 1 nF, RL = 10 , VDRVOUT = 0.7 V to 9.0 V VDRVOUT = 9.0 V to 0.7 V Maximum duty cycle Minimum controlled duty cycle 93 At 100 kHz zero power section PARAMETER Zero power comparator threshold TEST CONDITIONS Measured on VAOUT MIN TYP MAX UNITS 0.20 0.33 0.50 V pin descriptions CAI: (current amplifier noninverting input) Place a resistor between this pin and the GND side of current sense resistor. This input and the inverting input (MOUT) remain functional down to and below GND. CAOUT: (current amplifier output) This is the output of a wide bandwidth operational amplifier that senses line current and commands the PFC pulse-width modulator (PWM) to force the correct duty cycle. Compensation components are placed between CAOUT and MOUT. CT: (oscillator timing capacitor) A capacitor from CT to GND sets the PWM oscillator frequency according to: f[ RT0.6CT The lead from the oscillator timing capacitor to GND should be as short and direct as possible. DRVOUT: (gate drive) The output drive for the boost switch is a totem-pole MOSFET gate driver on DRVOUT. Use a series gate resistor to prevent interaction between the gate impedance and the output driver that might cause the DRVOUT to overshoot excessively. See characteristic curve (Figure 13) to determine minimum required gate resister value. Some overshoot of the DRVOUT output is always expected when driving a capacitive load. GND: (ground) All voltages measured with respect to ground. VCC and REF should be bypassed directly to GND with a 0.1-F or larger ceramic capacitor. www.ti.com 5 SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 pin descriptions (continued) IAC: (current proportional to input voltage) This input to the analog multiplier is a current proportional to instantaneous line voltage. The multiplier is tailored for very low distortion from this current input (IIAC) to multiplier output. The recommended maximum IIAC is 500 A. MOUT: (multiplier output and current amplifier inverting input) The output of the analog multiplier and the inverting input of the current amplifier are connected together at MOUT. As the multiplier output is a current, this is a high-impedance input so the amplifier can be configured as a differential amplifier. This configuration improves noise immunity and allows for the leading-edge modulation operation. The multiplier output current is limited to 2 I . The multiplier output current is given by the equation: IAC I (V * 1) VAOUT I + IAC MOUT 2 K V VFF where K + 1 is the multiplier gain constant. V OVP/EN: (over-voltage/enable) A window comparator input that disables the output driver if the boost output voltage is a programmed level above the nominal or disables both the PFC output driver and resets SS if pulled below 1.9 V (typ). PKLMT: (PFC peak current limit) The threshold for peak limit is 0 V. Use a resistor divider from the negative side of the current sense resistor to VREF to level shift this signal to a voltage level defined by the value of the sense resistor and the peak current limit. Peak current limit is reached when PKLMT voltage falls below 0 V. RT: (oscillator charging current) A resistor from RT to GND is used to program oscillator charging current. A resistor between 10 k and 100 k is recommended. Nominal voltage on this pin is 3 V. SS: (soft-start) VSS is discharged for VVCC low conditions. When enabled, SS charges an external capacitor with a current source. This voltage is used as the voltage error signal during start-up, enabling the PWM duty cycle to increase slowly. In the event of a VVCC dropout, the OVP/EN is forced below 1.9 V (typ), SS quickly discharges to disable the PWM. Note: In an open-loop test circuit, grounding the SS pin does not ensure 0% duty cycle. Please see the application section for details. VAOUT: (voltage amplifier output) This is the output of the operational amplifier that regulates output voltage. The voltage amplifier output is internally limited to approximately 5.5 V to prevent overshoot. VCC: (positive supply voltage) Connect to a stable source of at least 20 mA between 10 V and 17 V for normal operation. Bypass VCC directly to GND to absorb supply current spikes required to charge external MOSFET gate capacitances. To prevent inadequate gate drive signals, the output devices are inhibited unless VVCC exceeds the upper under-voltage lockout voltage threshold and remains above the lower threshold. VFF: (feed-forward voltage) The RMS voltage signal generated at this pin by mirroring 1/2 of the IIAC into a single pole external filter. At low line, the VFF voltage should be 1.4 V. VSENSE: (voltage amplifier inverting input) This is normally connected to a compensation network and to the boost converter output through a divider network. VREF: (voltage reference output) VREF is the output of an accurate 7.5-V voltage reference. This output is capable of delivering 20 mA to peripheral circuitry and is internally short-circuit current limited. VREF is disabled and remains at 0 V when VVCC is below the UVLO threshold. Bypass VREF to GND with a 0.1-F or larger ceramic capacitor for best stability. Please refer to Figures 8 and 9 for VREF line and load regulation characteristics. 6 www.ti.com SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 APPLICATION INFORMATION The UCC3817 is a BiCMOS average current mode boost controller for high power factor, high efficiency preregulator power supplies. Figure 1 shows the UCC3817 in a 250-W PFC preregulator circuit. Off-line switching power converters normally have an input current that is not sinusoidal. The input current waveform has a high harmonic content because current is drawn in pulses at the peaks of the input voltage waveform. An active power factor correction circuit programs the input current to follow the line voltage, forcing the converter to look like a resistive load to the line. A resistive load has 0 phase displacement between the current and voltage waveforms. Power factor can be defined in terms of the phase angle between two sinusoidal waveforms of the same frequency: PF + cos Q Therefore, a purely resistive load would have a power factor of 1. In practice, power factors of 0.999 with THD (total harmonic distortion) of less than 3% are possible with a well-designed circuit. Following guidelines are provided to design PFC boost converters using the UCC3817. NOTE: Schottky diodes, D5 and D6, are required to protect the PFC controller from electrical over stress during system power up. C10 1 F R16 100 C11 1 F VCC R21 383k R15 24k R13 383k D7 D8 L1 1mH IAC R18 24k AC2 + C14 1.5 F 400V VLINE 85-270 VAC VO D1 8A, 600V F1 D2 6A, 600V C13 0.47 F 600V R14 0.25 3W 6A 600V - R17 20 UCC3817 R9 4.02k R12 2k VOUT C12 385V-DC 220 F 450V Q1 IRFP450 D3 AC1 R10 4.02k 1 GND DRVOUT 16 2 PKLIMIT 3 CAOUT 4 CAI 5 MOUT CT 14 6 IAC SS 13 RT 12 VSENSE 11 D4 VCC VCC D5 R11 10k VREF R8 12k C3 1 F CER 15 C2 100 F AI EI C1 560pF C9 1.2nF C4 0.01 F C8 270pF R1 12k D6 C7 150nF R7 100k C15 2.2 F 7 VAOUT 8 VFF R3 20k R19 499k VO R20 274k R4 249k R2 499k C6 2.2 F OVP/EN 10 R6 30k C5 1F VREF R5 10k 9 VREF UDG-98183 Figure 1. Typical Application Circuit www.ti.com 7 SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 APPLICATION INFORMATION power stage LBOOST : The boost inductor value is determined by: L BOOST + VIN(min) (DI D fs) where D is the duty cycle, I is the inductor ripple current and fS is the switching frequency. For the example circuit a switching frequency of 100 kHz, a ripple current of 875 mA, a maximum duty cycle of 0.688 and a minimum input voltage of 85 VRMS gives us a boost inductor value of about 1 mH. The values used in this equation are at the peak of low line, where the inductor current and its ripple are at a maximum. COUT : Two main criteria, the capacitance and the voltage rating, dictate the selection of the output capacitor. The value of capacitance is determined by the holdup time required for supporting the load after input ac voltage is removed. Holdup is the amount of time that the output stays in regulation after the input has been removed. For this circuit, the desired holdup time is approximately 16 ms. Expressing the capacitor value in terms of output power, output voltage, and holdup time gives the equation: C OUT + 2 P Dt OUT VOUT2 * VOUT(min)2 In practice, the calculated minimum capacitor value may be inadequate because output ripple voltage specifications limit the amount of allowable output capacitor ESR. Attaining a sufficiently low value of ESR often necessitates the use of a much larger capacitor value than calculated. The amount of output capacitor ESR allowed can be determined by dividing the maximum specified output ripple voltage by the inductor ripple current. In this design holdup time was the dominant determining factor and a 220-F, 450-V capacitor was chosen for the output voltage level of 385 VDC at 250 W. Power switch selection: As in any power supply design, tradeoffs between performance, cost and size have to be made. When selecting a power switch, it can be useful to calculate the total power dissipation in the switch for several different devices at the switching frequencies being considered for the converter. Total power dissipation in the switch is the sum of switching loss and conduction loss. Switching losses are the combination of the gate charge loss, COSS loss and turnon and turnoff losses: P P P GATE +Q COSS +1 2 ON )P V GATE OFF C OSS +1 2 V fs GATE V2 OFF OFF I L fs tON ) tOFF fs where QGATE is the total gate charge, VGATE is the gate drive voltage, fS is the clock frequency, COSS is the drain source capacitance of the MOSFET, IL is the peak inductor current, tON and tOFF are the switching times (estimated using device parameters RGATE, QGD and VTH) and VOFF is the voltage across the switch during the off time, in this case VOFF = VOUT. 8 www.ti.com SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 APPLICATION INFORMATION Conduction loss is calculated as the product of the RDS(on) of the switch (at the worst case junction temperature) and the square of RMS current: P COND +R DS(on) K I2 RMS where K is the temperature factor found in the manufacturer's RDS(on) vs. junction temperature curves. Calculating these losses and plotting against frequency gives a curve that enables the designer to determine either which manufacturer's device has the best performance at the desired switching frequency, or which switching frequency has the least total loss for a particular power switch. For this design example an IRFP450 HEXFET from International Rectifier was chosen because of its low RDS(on) and its VDSS rating. The IRFP450's RDS(on) of 0.4 and the maximum VDSS of 500 V made it an ideal choice. An excellent review of this procedure can be found in the Unitrode Power Supply Design Seminar SEM1200, Topic 6, Design Review: 140 W, [Multiple Output High Density DC/DC Converter]. softstart The softstart circuitry is used to prevent overshoot of the output voltage during start up. This is accomplished by bringing up the voltage amplifier's output (VVAOUT) slowly which allows for the PWM duty cycle to increase slowly. Please use the following equation to select a capacitor for the softstart pin. In this example tDELAY is equal to 7.5 ms, which would yield a CSS of 10 nF. C SS + 10 mA t DELAY 7.5 V In an open-loop test circuit, shorting the softstart pin to ground does not ensure 0% duty cycle. This is due to the current amplifiers input offset voltage, which could force the current amplifier output high or low depending on the polarity of the offset voltage. However, in the typical application there is sufficient amount of inrush and bias current to overcome the current amplifier's offset voltage. multiplier The output of the multiplier of the UCC3817 is a signal representing the desired input line current. It is an input to the current amplifier, which programs the current loop to control the input current to give high power factor operation. As such, the proper functioning of the multiplier is key to the success of the design. The inputs to the multiplier are VAOUT, the voltage amplifier error signal, IIAC, a representation of the input rectified ac line voltage, and an input voltage feedforward signal, VVFF. The output of the multiplier, IMOUT, can be expressed as: I MOUT +I VVAOUT * 1 IAC K V 2 VFF where K is a constant typically equal to 1 . V The electrical characteristics table covers all the required operating conditions for designing with the multiplier. Additionally, curves in figures 10, 11, and 12 provide typical multiplier characteristics over its entire operating range. www.ti.com 9 SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 APPLICATION INFORMATION multiplier (continued) The IIAC signal is obtained through a high-value resistor connected between the rectified ac line and the IAC pin of the UCC3817/18. This resistor (RIAC) is sized to give the maximum IIAC current at high line. For the UCC3817/18 the maximum IIAC current is about 500 A. A higher current than this can drive the multiplier out of its linear range. A smaller current level is functional, but noise can become an issue, especially at low input line. Assuming a universal line operation of 85 VRMS to 265 VRMS gives a RIAC value of 750 k. Because of voltage rating constraints of standard 1/4-W resistor, use a combination of lower value resistors connected in series to give the required resistance and distribute the high voltage amongst the resistors. For this design example two 383-k resistors were used in series. The current into the IAC pin is mirrored internally to the VFF pin where it is filtered to produce a voltage feed forward signal proportional to line voltage. The VFF voltage is used to keep the power stage gain constant; and to provid input power limiting. Please refer to Texas Instruments application note SLUA196 for detailed explanation on how the VFF pin provides power limiting. The following equation can be used to size the VFF resistor (RVFF) to provide power limiting where VIN(min) is the minimum RMS input voltage and RIAC is the total resistance connected between the IAC pin and the rectified line voltage. R VFF + 1.4 V V 0.9 IN(min) 2 R IAC [ 30 kW Because the VFF voltage is generated from line voltage it needs to be adequately filtered to reduce total harmonic distortion caused by the 120 Hz rectified line voltage. Refer to Unitrode Power Supply Design Seminar, SEM-700 Topic 7, [Optimizing the Design of a High Power Factor Preregulator.] A single pole filter was adequate for this design. Assuming that an allocation of 1.5% total harmonic distortion from this input is allowed, and that the second harmonic ripple is 66% of the input ac line voltage, the amount of attenuation required by this filter is: 1.5 % + 0. 022 66 % With a ripple frequency (fR) of 120 Hz and an attenuation of 0.022 requires that the pole of the filter (fP) be placed at: f + 120 Hz P 0.022 [ 2.6 Hz The following equation can be used to select the filter capacitor (CVFF) required to produce the desired low pass filter. C VFF + 2 1 R VFF p f [ 2.2 mF P The RMOUT resistor is sized to match the maximum current through the sense resistor to the maximum multiplier current. The maximum multiplier current, or IMOUT(max), can be determined by the equation: I I 10 MOUT(max) + VVAOUT(max) * 1V @V IN(min) IAC K V 2 VFF (min) www.ti.com SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 APPLICATION INFORMATION multiplier (continued) IMOUT(max) for this design is approximately 315 A. The RMOUT resistor can then be determined by: R MOUT + V I RSENSE MOUT(max) In this example VRSENSE was selected to give a dynamic operating range of 1.25 V, which gives an RMOUT of roughly 3.91 k. voltage loop The second major source of harmonic distortion is the ripple on the output capacitor at the second harmonic of the line frequency. This ripple is fed back through the error amplifier and appears as a 3rd harmonic ripple at the input to the multiplier. The voltage loop must be compensated not just for stability but also to attenuate the contribution of this ripple to the total harmonic distortion of the system. (refer to Figure 2). Cf VOUT CZ Rf R IN - RD + VREF Figure 2. Voltage Amplifier Configuration The gain of the voltage amplifier, GVA, can be determined by first calculating the amount of ripple present on the output capacitor. The peak value of the second harmonic voltage is given by the equation: V OPK + P 2 p f R C IN OUT V OUT In this example VOPK is equal to 3.91 V. Assuming an allowable contribution of 0.75% (1.5% peak to peak) from the voltage loop to the total harmonic distortion budget we set the gain equal to: G VA + DVVAOUT(0.015) 2 V OPK where VVAOUT is the effective output voltage range of the error amplifier (5 V for the UCC3817). The network needed to realize this filter is comprised of an input resistor, RIN, and feedback components Cf, CZ, and Rf. The value of RIN is already determined because of its function as one half of a resistor divider from VOUT feeding back to the voltage amplifier for output voltage regulation. In this case the value was chosen to be 1 M. This high value was chosen to reduce power dissipation in the resistor. In practice, the resistor value would be realized by the use of two 500-k resistors in series because of the voltage rating constraints of most standard 1/4-W resistors. The value of Cf is determined by the equation: www.ti.com 11 SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 APPLICATION INFORMATION voltage loop (continued) C + f 1 2 p f G R VA R IN In this example Cf equals 150 nF. Resistor Rf sets the dc gain of the error amplifier and thus determines the frequency of the pole of the error amplifier. The location of the pole can be found by setting the gain of the loop equation to one and solving for the crossover frequency. The frequency, expressed in terms of input power, can be calculated by the equation: f 2 VI + P (2 p)2 DV VAOUT V IN OUT R IN C OUT C f fVI for this converter is 10 Hz. A derivation of this equation can be found in the Unitrode Power Supply Design Seminar SEM1000, Topic 1, [A 250-kHz, 500-W Power Factor Correction Circuit Employing Zero Voltage Transitions]. Solving for Rf becomes: R + f 1 2 p f VI C f or Rf equals 100 k. Due to the low output impedance of the voltage amplifier, capacitor CZ was added in series with RF to reduce loading on the voltage divider. To ensure the voltage loop crossed over at fVI, CZ was selected to add a zero at a 10th of fVI. For this design a 2.2-F capacitor was chosen for CZ. The following equation can be used to calculate CZ. C + Z 2 p 1 f VI 10 R f current loop The gain of the power stage is: G (s) + ID VOUT RSENSE s LBOOST VP RSENSE has been chosen to give the desired differential voltage for the current sense amplifier at the desired current limit point. In this example, a current limit of 4 A and a reasonable differential voltage to the current amp of 1 V gives a RSENSE value of 0.25 . VP in this equation is the voltage swing of the oscillator ramp, 4 V for the UCC3817. Setting the crossover frequency of the system to 1/10th of the switching frequency, or 10 kHz, requires a power stage gain at that frequency of 0.383. In order for the system to have a gain of 1 at the crossover frequency, the current amplifier needs to have a gain of 1/GID at that frequency. GEA, the current amplifier gain is then: G 12 EA + 1 + 1 + 2.611 0.383 G ID www.ti.com SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 APPLICATION INFORMATION current loop (continued) RI is the RMOUT resistor, previously calculated to be 3.9 k. (refer to Figure 3). The gain of the current amplifier is Rf/RI, so multiplying RI by GEA gives the value of Rf, in this case approximately 12 k. Setting a zero at the crossover frequency and a pole at half the switching frequency completes the current loop compensation. C + Z 2 C + P p 1 R f f C 1 2 p R f fs 2 C P C Rf Z RI - CAOUT + Figure 3. Current Loop Compensation The UCC3817 current amplifier has the input from the multiplier applied to the inverting input. This change in architecture from previous Texas Instruments PFC controllers improves noise immunity in the current amplifier. It also adds a phase inversion into the control loop. The UCC3817 takes advantage of this phase inversion to implement leading-edge duty cycle modulation. Synchronizing a boost PFC controller to a downstream dc-to-dc controller reduces the ripple current seen by the bulk capacitor between stages, reducing capacitor size and cost and reducing EMI. This is explained in greater detail in a following section. The UCC3817 current amplifier configuration is shown in Figure 4. L BOOST V OUT - R SENSE Q BOOST + Zf MULT CA PWM COMPARATOR - - + + Figure 4. UCC3817 Current Amplifier Configuration www.ti.com 13 SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 APPLICATION INFORMATION start up The UCC3818 version of the device is intended to have VCC connected to a 12-V supply voltage. The UCC3817 has an internal shunt regulator enabling the device to be powered from bootstrap circuitry as shown in the typical application circuit of Figure 1. The current drawn by the UCC3817 during undervoltage lockout, or start-up current, is typically 150 A. Once VCC is above the UVLO threshold, the device is enabled and draws 4 mA typically. A resistor connected between the rectified ac line voltage and the VCC pin provides current to the shunt regulator during power up. Once the circuit is operational, the bootstrap winding of the inductor provides the VCC voltage. Sizing of the start-up resistor is determined by the start-up time requirement of the system design. I + C DV C Dt V R + RMS I (0.9) C Where IC is the charge current, C is the total capacitance at the VCC pin, V is the UVLO threshold and t is the allowed start-up time. Assuming a 1 second allowed start-up time, a 16-V UVLO threshold, and a total VCC capacitance of 100 F, a resistor value of 51 k is required at a low line input voltage of 85 VRMS. The IC start-up current is sufficiently small as to be ignored in sizing the start-up resistor. capacitor ripple reduction For a power system where the PFC boost converter is followed by a dc-to-dc converter stage, there are benefits to synchronizing the two converters. In addition to the usual advantages such as noise reduction and stability, proper synchronization can significantly reduce the ripple currents in the boost circuit's output capacitor. Figure 5 helps illustrate the impact of proper synchronization by showing a PFC boost converter together with the simplified input stage of a forward converter. The capacitor current during a single switching cycle depends on the status of the switches Q1 and Q2 and is shown in Figure 6. It can be seen that with a synchronization scheme that maintains conventional trailing-edge modulation on both converters, the capacitor current ripple is highest. The greatest ripple current cancellation is attained when the overlap of Q1 offtime and Q2 ontime is maximized. One method of achieving this is to synchronize the turnon of the boost diode (D1) with the turnon of Q2. This approach implies that the boost converter's leading edge is pulse width modulated while the forward converter is modulated with traditional trailing edge PWM. The UCC3817 is designed as a leading edge modulator with easy synchronization to the downstream converter to facilitate this advantage. Table 1 compares the ICB(rms) for D1/Q2 synchronization as offered by UCC3817 vs. the ICB(rms) for the other extreme of synchronizing the turnon of Q1 and Q2 for a 200-W power system with a VBST of 385 V. UDG-97130-1 Figure 5. Simplified Representation of a 2-Stage PFC Power Supply 14 www.ti.com SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 APPLICATION INFORMATION capacitor ripple reduction (continued) UDG-97131 Figure 6. Timing Waveforms for Synchronization Scheme Table 1. Effects of Synchronization on Boost Capacitor Current VIN = 85 V D1/Q2 VIN = 120 V D1/Q2 Q1/Q2 VIN = 240 V D1/Q2 D(Q2) Q1/Q2 Q1/Q2 0.35 1.491 A 0.835 A 1.341 A 0.663 A 1.024 A 0.731 A 0.45 1.432 A 0.93 A 1.276 A 0.664 A 0.897 A 0.614 A Table 1 illustrates that the boost capacitor ripple current can be reduced by about 50% at nominal line and about 30% at high line with the synchronization scheme facilitated by the UCC3817. Figure 7 shows the suggested technique for synchronizing the UCC3817 to the downstream converter. With this technique, maximum ripple reduction as shown in Figure 6 is achievable. The output capacitance value can be significantly reduced if its choice is dictated by ripple current or the capacitor life can be increased as a result. In cost sensitive designs where holdup time is not critical, this is a significant advantage. An alternative method of synchronization to achieve the same ripple reduction is possible. In this method, the turnon of Q1 is synchronized to the turnoff of Q2. While this method yields almost identical ripple reduction and maintains trailing edge modulation on both converters, the synchronization is much more difficult to achieve and the circuit can become susceptible to noise as the synchronizing edge itself is being modulated. www.ti.com 15 SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 APPLICATION INFORMATION capacitor ripple reduction (continued) Gate Drive From Down Stream PWM C1 UCC3817 D2 CT CT RT D1 RT Figure 7. Synchronizing the UCC3817 to a Down-Stream Converter REFERENCE VOLTAGE vs REFERENCE CURRENT REFERENCE VOLTAGE vs SUPPLY VOLTAGE 7.510 VREF - Reference Voltage - V VREF - Reference Voltage - V 7.60 7.55 7.50 7.45 7.505 7.500 7.495 7.490 7.40 9 10 11 12 13 14 5 10 15 20 IVREF - Reference Current - mA VCC - Supply Voltage - V Figure 8 16 0 Figure 9 www.ti.com 25 SLUS395J - FEBRUARY 2000 - REVISED MARCH 2009 APPLICATION INFORMATION MULTIPLIER OUTPUT CURRENT vs VOLTAGE ERROR AMPLIFIER OUTPUT MULTIPLIER GAIN vs VOLTAGE ERROR AMPLIFIER OUTPUT 1.5 IAC = 150 A VFF = 1.4 V 300 1.3 IAC = 150 A 250 200 Multiplier Gain - K IMOUT - Multiplier Output Current - A 350 IAC = 300 A VFF = 3.0 V 150 100 1.1 0.9 IAC = 300 A IAC = 500 A 0.7 50 IAC = 500 A VFF = 4.7 V 0 0.0 1.0 2.0 3.0 4.0 0.5 1.0 5.0 2.0 Figure 10 (VFF x IMOUT) - W 400 VAOUT = 5 V 300 VAOUT = 4 V 200 VAOUT = 3 V 100 VAOUT = 2 V 0 3.0 4.0 5.0 RGATE - Recommended Minimum Gate Resistance - 500 2.0 5.0 Figure 11 MULTIPLIER CONSTANT POWER PERFORMANCE 1.0 4.0 VAOUT - Voltage Error Amplifier Output - V VAOUT - Voltage Error Amplifier Output - V 0.0 3.0 RECOMMENDED MINIMUM GATE RESISTANCE vs SUPPLY VOLTAGE 17 16 15 14 13 12 11 10 9 8 10 12 14 16 18 20 VCC - Supply Voltage - V VFF - Feedforward Voltage - V Figure 12 Figure 13 www.ti.com 17 PACKAGE OPTION ADDENDUM www.ti.com 7-Aug-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty UCC2817D ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2817DG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2817DTR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2817DTRG4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2817DW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC2817DWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC2817N ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC2817NG4 ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC2817PW ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC2817PWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC2818D ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2818DG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2818DTR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2818DTRG4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC2818DW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC2818DWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC2818DWTR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC2818DWTRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC2818N ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC2818NG4 ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC2818PW ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC2818PWG4 ACTIVE TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC3817D ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC3817DG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC3817DTR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 Lead/Ball Finish MSL Peak Temp (3) PACKAGE OPTION ADDENDUM www.ti.com 7-Aug-2009 Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty UCC3817DTRG4 ACTIVE SOIC D 16 UCC3817DW ACTIVE SOIC DW 16 40 UCC3817DWG4 ACTIVE SOIC DW 16 40 UCC3817DWTR ACTIVE SOIC DW UCC3817DWTRG4 ACTIVE SOIC UCC3817N ACTIVE UCC3817NG4 2500 Green (RoHS & no Sb/Br) Lead/Ball Finish MSL Peak Temp (3) CU NIPDAU Level-1-260C-UNLIM Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type ACTIVE PDIP N 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UCC3818D ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC3818DG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC3818DTR ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC3818DTRG4 ACTIVE SOIC D 16 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM UCC3818DW ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC3818DWG4 ACTIVE SOIC DW 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC3818DWTR ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC3818DWTRG4 ACTIVE SOIC DW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UCC3818N ACTIVE PDIP N 16 CU NIPDAU N / A for Pkg Type UCC3818N/81511 OBSOLETE PDIP N 16 UCC3818NG4 ACTIVE PDIP N UCC3818PW ACTIVE TSSOP UCC3818PWG4 ACTIVE UCC3818PWTR UCC3818PWTRG4 25 Green (RoHS & no Sb/Br) TBD Call TI 16 25 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR TSSOP PW 16 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ACTIVE TSSOP PW 16 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 7-Aug-2009 http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF UCC2818 : * Enhanced Product: UCC2818-EP NOTE: Qualified Version Definitions: * Enhanced Product - Supports Defense, Aerospace and Medical Applications Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2009 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing UCC2817DTR SOIC SPQ Reel Reel Diameter Width (mm) W1 (mm) D 16 2500 330.0 16.4 A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 6.5 10.3 2.1 8.0 16.0 Q1 UCC2818DTR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 UCC2818DWTR SOIC DW 16 2000 330.0 16.4 10.85 10.8 2.7 12.0 16.0 Q1 UCC3817DTR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 UCC3817DWTR SOIC DW 16 2000 330.0 16.4 10.85 10.8 2.7 12.0 16.0 Q1 UCC3818DTR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1 UCC3818DWTR SOIC DW 16 2000 330.0 16.4 10.85 10.8 2.7 12.0 16.0 Q1 UCC3818PWTR TSSOP PW 16 2000 330.0 12.4 7.0 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2009 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UCC2817DTR SOIC D 16 2500 333.2 345.9 28.6 UCC2818DTR SOIC D 16 2500 333.2 345.9 28.6 UCC2818DWTR SOIC DW 16 2000 346.0 346.0 33.0 UCC3817DTR SOIC D 16 2500 333.2 345.9 28.6 UCC3817DWTR SOIC DW 16 2000 346.0 346.0 33.0 UCC3818DTR SOIC D 16 2500 333.2 345.9 28.6 UCC3818DWTR SOIC DW 16 2000 346.0 346.0 33.0 UCC3818PWTR TSSOP PW 16 2000 346.0 346.0 29.0 Pack Materials-Page 2 MECHANICAL DATA MTSS001C - JANUARY 1995 - REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DLP(R) Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee(R) Solutions amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2009, Texas Instruments Incorporated