E5GN-Q1T-C AC100-240N6 - Omron Automation and Safety

CSM_E5GN_DS_E_5_1

Basic-type Digital Temperature Controller

E5GN (48 x 24 mm)

New 48 x 24-mm Basic Temperature

Controller with Enhanced Functions and

Performance. Improved Indication

Accuracy and Preventive Maintenance

Function.

• Indication Accuracy

Thermocouple input: ±0.3% of PV (previous models: ±0.5%)

Pt input: ±0.2% of PV (previous models: ±0.5%)

Analog input: ±0.2% FS (previous models: ±0.5%)

• Models are available with screw terminal blocks or screwless

clamp terminal blocks.

•

A PV/SV-status display function can be set to automatically

alternate between displaying the status of the Temperature

Controller (auto/manual, RUN/STOP, and alarms) and the PV or SV.

• Preventive maintenance for relays in the Temperature Controller

using a Control Output ON/OFF Counter.

• Switch the PV display between three colors.

• Compatible with Support Software (CX-Thermo version 4.2 or higher).

• Eleven-segment displays.

• Models are available with one or two alarm outputs.

Main I/O Functions

E5GN

Models with Screw Terminal

Blocks

48 × 24 mm

E5GN--@-C

Models with Screwless Clamp

Terminal Blocks

48 × 24 mm

Refer to Safety Precautions for E5

N/E5

N-H.

Refer to Operation for E5

N/E5

N-H for operating

procedures.

Event Inputs

• None

• Two

Sensor Inputs

• Universal thermocouple/Pt inputs

(Models with temperature inputs)

• Analog current/voltage inputs

(Models with analog inputs)

Indication Accuracy

• Thermocouple input: ±0.3% of PV

• Pt input: ±0.2% of PV

• Analog input: ±0.2% FS

Sampling Period

• 250 ms

Control Output 1

• Relay output

• Voltage output (for driving SSR)

• Current output

Auxiliary Outputs

• None

• One

• Two

Dual Display: PV and SV 4-digit Display

E5GN

• Auto/manual switching

• Temperature Controller status display

• Simple program function

• Control output ON/OFF count alarm

• PV change rate alarm

• Models also available with RS-232C

communications

• Models also available with RS-485

communications

This datasheet is provided as a guideline for selecting products. Be sure to refer to the following user manuals for application precautions

and other information required for operation before attempting to use the product.

E5CN/E5AN/E5EN/E5GN Digital Temperature Controllers User's Manual Basic Type (Cat. No. H156)

E5CN/E5AN/E5EN/E5GN Digital Temperature Controllers Communications Manual Basic Type (Cat. No. H158)

E5GN

Lineup

Note: Models with one control output and one or two auxiliary outputs can be used for heating/cooling control.

Model Number Structure

Model Number Legend

Controllers

1. Control Output 1

R: Relay output

Q: Voltage output (for driving SSR)

C: Linear current output

2. Auxiliary Outputs

Blank: None

1: One output

2: Two outputs

3. Option

Blank: None

01: RS-232C communications

03: RS-485 communications

B: Two event inputs

H: Heater burnout/Heater short/Heater overcurrent detection

(CT1)

4. Input Type

T: Universal thermocouple/platinum resistance thermometer input

L: Analog current/voltage input

5. Power Supply Voltage

Blank: 100 to 240 VAC

D: 24 VAC/VDC

6. Terminal Type

Blank: Models with screw terminal block

C: Models with screwless clamp terminal block

7. Case Color

Blank: Black

8. Communications Protocol

Blank: None

FLK: CompoWay/F serial communications

Note: Models cannot be made for all combinations of options that are possible in the model number legend. Confirm model availability in Ordering

Information before ordering.

*Auxiliary outputs are relay outputs that can be used for output alarms or processing results.

Supply Voltage Suffixes for Ordering

For 100 to 240 VAC, add a "AC100240" suffix.

For 24 VAC/VDC models, add a "ACDC24" suffix.

Screwless clamp

terminal block

Screw terminal block

E5GN

Basic Type

Analog input

Temperature input

1 control output

1 control output 0, 1, or 2 auxiliary

outputs

0, 1, or 2 auxiliary

outputs

Analog input

Temperature input

1 control output

1 control output 0, 1, or 2 auxiliary

outputs

0, 1, or 2 auxiliary

outputs

1 2

E5GN-@@@@@-@-@-@

3 4 5 6 7 8

E5GN

Ordering Information

Controllers with Screw Terminal Blocks

Models with Temperature Inputs

Models with One Control Output and a 100 to 240-VAC Power Supply (Add AC100240 to the Model number.)

*1. If heating/cooling control mode is used, an auxiliary output is used as a control output for the cooling side. The number of auxiliary outputs that

can be used will decrease by one. Also, the signal for the control output for the cooling side will be a relay output.

*2. A current control output can be used as the transfer output. In that case, an auxiliary output is used as the control output. (This is not possible

for models without an auxiliary output.) The control output will be a relay output. The number of auxiliary outputs that can be used will decrease

by one.

Case color Control

output

Control

mode *1

No. of

auxiliary

outputs

Detection of

heater

burnout,

SSR failure,

and heater

overcurrent

No. of event

inputs

Transfer

output *2

Communi-

cations

Previous model

New model

Thermocou-

ple input

Resistance

thermome-

ter input

Black

Relay output

Standard ---

---

E5GN-RTC E5GN-RP E5GN-RT

Standard or

heating/

cooling

E5GN-R1TC E5GN-R1P E5GN-R1T

2 --- --- E5GN-R1BT

---

RS-232C --- --- E5GN-

R101T-FLK

RS-485 E5GN

-R03TC-FLK

E5GN

-R03P-FLK

E5GN-

R103T-FLK

---

--- --- E5GN-R2T

Detection for

single-phase

heaters

--- --- E5GN-R2HT

---

2 --- --- E5GN-R2BT

--- RS-485 --- --- E5GN-

R203T-FLK

Voltage

output (for

driving SSR)

Standard ---

---

E5GN-QTC E5GN-QP E5GN-QT

Standard or

heating/

cooling

E5GN-Q1TC E5GN-Q1P E5GN-Q1T

2 --- --- E5GN-Q1BT

---

RS-232C --- --- E5GN-

Q101T-FLK

RS-485 E5GN

-Q03TC-FLK

E5GN

-Q03P-FLK

E5GN-

Q103T-FLK

---

--- --- E5GN-Q2T

Detection for

single-phase

heaters

--- --- E5GN-Q2HT

---

2 --- --- E5GN-Q2BT

--- RS-485 --- --- E5GN-

Q203T-FLK

Current

output

Standard or

heating/

cooling

1 ---

---

Transfer

output using

control

output

--- --- --- E5GN-C1T

2 --- --- E5GN-C1BT

---

RS-232C --- --- E5GN-

C101T-FLK

RS-485 --- --- E5GN-

C103T-FLK

E5GN

Models with One Control Output and a 24-VAC/VDC Power Supply (Add ACDC24 to the Model number.)

*1. If heating/cooling control mode is used, an auxiliary output is used as a control output for the cooling side. The number of auxiliary outputs that

can be used will decrease by one. Also, the signal for the control output for the cooling side will be a relay output.

*2. A current control output can be used as the transfer output. In that case, an auxiliary output is used as the control output. (This is not possible

for models without an auxiliary output.) The control output will be a relay output. The number of auxiliary outputs that can be used will decrease

by one.

Case color Control

output

Control

mode *1

No. of

auxiliary

outputs

Detection of

heater

burnout,

SSR failure,

and heater

overcurrent

No. of event

inputs

Transfer

output *2

Communi-

cations

Previous model

New model

Thermocou-

ple input

Resistance

thermome-

ter input

Black

Relay output

Standard ---

---

E5GN-RTC E5GN-RP E5GN-RTD

Standard or

heating/

cooling

E5GN-R1TC E5GN-R1P E5GN-R1TD

2 --- --- E5GN-R1BTD

---

RS-232C --- --- E5GN

-R101TD-FLK

RS-485 E5GN

-R03TC-FLK

E5GN

-R03P-FLK

E5GN

-R103TD-FLK

---

--- --- E5GN-R2TD

Detection for

single-phase

heaters

--- --- E5GN-R2HTD

---

2 --- --- E5GN-R2BTD

--- RS-485 --- --- E5GN

-R203TD-FLK

Voltage

output (for

driving SSR)

Standard ---

---

E5GN-QTC E5GN-QP E5GN-QTD

Standard or

heating/

cooling

E5GN-Q1TC E5GN-Q1P E5GN-Q1TD

2 --- --- E5GN-

Q1BTD

---

RS-232C --- --- E5GN-

Q101TD-FLK

RS-485 E5GN

-Q03TC-FLK

E5GN

-Q03P-FLK

E5GN

-Q103TD-FLK

---

--- --- E5GN-Q2TD

Detection for

single-phase

heaters

--- --- E5GN-

Q2HTD

---

2 --- --- E5GN-

Q2BTD

--- RS-485 --- --- E5GN

-Q203TD-FLK

Current

output

Standard or

heating/

cooling

1 ---

---

Transfer

output using

control

output

--- --- --- E5GN-C1TD

2 --- --- E5GN-C1BTD

---

RS-232C --- --- E5GN

-C101TD-FLK

RS-485 --- --- E5GN

-C103TD-FLK

E5GN

Models with Analog Inputs

Models with One Control Output and a 100 to 240-VAC Power Supply (Add AC100240 to the Model number.)

Note: Models with analog inputs do not display the temperature unit.

*1. If heating/cooling control mode is used, an auxiliary output is used as a control output for the cooling side. The number of auxiliary outputs that

can be used will decrease by one. Also, the signal for the control output for the cooling side will be a relay output.

*2. A current control output can be used as the transfer output. In that case, an auxiliary output is used as the control output. (This is not possible

for models without an auxiliary output.) The control output will be a relay output. The number of auxiliary outputs that can be used will decrease

by one.

Models with One Control Output and a 24-VAC/VDC Power Supply (Add ACDC24 to the Model number.)

*1. If heating/cooling control mode is used, an auxiliary output is used as a control output for the cooling side. The number of auxiliary outputs that

can be used will decrease by one. Also, the signal for the control output for the cooling side will be a relay output.

*2. A current control output can be used as the transfer output. In that case, an auxiliary output is used as the control output. (This is not possible

for models without an auxiliary output.) The control output will be a relay output. The number of auxiliary outputs that can be used will decrease

by one.

Case color Control

output

Control

mode *1

No. of

auxiliary

outputs

Detection of

heater

burnout,

SSR failure,

and heater

overcurrent

No. of event

inputs

Transfer

output *2

Communi-

cations

Previous model

New model

Thermocou-

ple input

Resistance

thermome-

ter input

Black

Relay output

Standard or

heating/

cooling

1 --- ---

--- RS-485

--- --- E5GN-

R103L-FLK

Voltage

output (for

driving SSR)

--- --- E5GN-

Q103L-FLK

Current

output

Transfer

output using

control

output

--- --- --- E5GN-C1L

Case color Control

output

Control

mode *1

No. of

auxiliary

outputs

Detection of

heater

burnout,

SSR failure,

and heater

overcurrent

No. of event

inputs

Transfer

output *2

Communi-

cations

Previous model

New model

Thermocou-

ple input

Resistance

thermome-

ter input

Black

Relay output

Standard or

heating/

cooling 1 --- ---

--- RS-485

--- --- E5GN-

R103LD-FLK

Voltage

output (for

driving SSR)

--- --- E5GN

-Q103LD-FLK

Current

output

Transfer

output using

control

output

--- --- --- E5GN-C1LD

E5GN

Controllers with Screwless Clamp Terminal Blocks

Models with Temperature Inputs

Models with One Control Output and a 100 to 240-VAC Power Supply (Add AC100240 to the Model number.)

*1. If heating/cooling control mode is used, an auxiliary output is used as a control output for the cooling side. The number of auxiliary outputs that

can be used will decrease by one. Also, the signal for the control output for the cooling side will be a relay output.

*2. A current control output can be used as the transfer output. In that case, an auxiliary output is used as the control output. (This is not possible

for models without an auxiliary output.) The control output will be a relay output. The number of auxiliary outputs that can be used will decrease

by one.

Case color Control

output

Control

mode *1

No. of

auxiliary

outputs

Detection

of heater

burnout,

SSR failure,

and heater

overcurrent

No. of event

inputs

Transfer

output *2

Communic

ations

Previous model

New model

Thermocou-

ple input

Resistance

thermome-

ter input

Black

Relay output

Standard ---

---

E5GN-RTC E5GN-RP E5GN-RT-C

Standard or

heating/

cooling

E5GN-R1TC E5GN-R1P E5GN-R1T-C

2 --- --- E5GN-R1BT-C

---

RS-232C --- --- E5GN

-R101T-C-FLK

RS-485 E5GN

-R03TC-FLK

E5GN

-R03P-FLK

E5GN

-R103T-C-FLK

---

--- --- E5GN-R2T-C

Detection for

single-

phase

heaters

--- --- E5GN-R2HT-C

---

2 --- --- E5GN-R2BT-C

--- RS-485 --- --- E5GN

-R203T-C-FLK

Voltage

output (for

driving SSR)

Standard ---

---

E5GN-QTC E5GN-QP E5GN-QT-C

Standard or

heating/

cooling

E5GN-Q1TC E5GN-Q1P E5GN-Q1T-C

2 --- --- E5GN-Q1BT-C

---

RS-232C --- --- E5GN

-Q101T-C-FLK

RS-485 E5GN

-Q03TC-FLK

E5GN

-Q03P-FLK

E5GN

-Q103T-C-FLK

---

--- --- E5GN-Q2T-C

Detection for

single-

phase

heaters

--- --- E5GN-Q2HT-C

---

2 --- --- E5GN-Q2BT-C

--- RS-485 --- --- E5GN

-Q203T-C-FLK

Current

output

Standard or

heating/

cooling

---

Transfer

output using

control

output

--- --- --- E5GN-C1T-C

2 --- --- E5GN-C1BT-C

---

RS-232C --- --- E5GN

-C101T-C-FLK

RS-485 --- --- E5GN

-C103T-C-FLK

E5GN

Models with One Control Output and a 24-VAC/VDC Power Supply (Add ACDC24 to the Model number.)

*1. If heating/cooling control mode is used, an auxiliary output is used as a control output for the cooling side. The number of auxiliary outputs that

can be used will decrease by one. Also, the signal for the control output for the cooling side will be a relay output.

*2. A current control output can be used as the transfer output. In that case, an auxiliary output is used as the control output. (This is not possible

for models without an auxiliary output.) The control output will be a relay output. The number of auxiliary outputs that can be used will decrease

by one.

Case color Control

output

Control

mode *1

No. of

auxiliary

outputs

Detection

of heater

burnout,

SSR

failure, and

heater

overcurren

No. of

event

inputs

Transfer

output *2

Communic

ations

Previous model

New model

Thermocou-

ple input

Resistance

thermome-

ter input

Black

Relay

output

Standard ---

---

E5GN-RTC E5GN-RP E5GN-RTD-C

Standard or

heating/

cooling

E5GN-R1TC E5GN-R1P E5GN-R1TD-C

2 --- --- E5GN-R1BTD-C

---

RS-232C --- --- E5GN

-R101TD-C-FLK

RS-485 E5GN

-R03TC-FLK

E5GN

-R03P-FLK

E5GN

-R103TD-C-FLK

---

--- --- E5GN-R2TD-C

Detection

for single-

phase

heaters

--- --- E5GN-R2HTD-C

---

2 --- --- E5GN-R2BTD-C

--- RS-485 --- --- E5GN

-R203TD-C-FLK

Voltage

output (for

driving

SSR)

Standard ---

---

E5GN-QTC E5GN-QP E5GN-QTD-C

Standard or

heating/

cooling

E5GN-Q1TC E5GN-Q1P E5GN-Q1TD-C

2 --- --- E5GN-Q1BTD-C

---

RS-232C --- --- E5GN

-Q101TD-C-FLK

RS-485 E5GN

-Q03TC-FLK

E5GN

-Q03P-FLK

E5GN

-Q103TD-C-FLK

---

--- --- E5GN-Q2TD-C

Detection

for single-

phase

heaters

--- --- E5GN-Q2HTD-C

---

2 --- --- E5GN-Q2BTD-C

--- RS-485 --- --- E5GN

-Q203TD-C-FLK

Current

output

Standard or

heating/

cooling

1 ---

---

Transfer

output using

control

output

--- --- --- E5GN-C1TD-C

2 --- --- E5GN-C1BTD-C

---

RS-232C --- --- E5GN

-C101TD-C-FLK

RS-485 --- --- E5GN

-C103TD-C-FLK

E5GN

Models with Analog Inputs

Models with One Control Output and a 100 to 240-VAC Power Supply (Add AC100240 to the Model number.)

Note: Models with analog inputs do not display the temperature unit.

*1. If heating/cooling control mode is used, an auxiliary output is used as a control output for the cooling side. The number of auxiliary outputs that

can be used will decrease by one. Also, the signal for the control output for the cooling side will be a relay output.

*2. A current control output can be used as the transfer output. In that case, an auxiliary output is used as the control output. (This is not possible

for models without an auxiliary output.) The control output will be a relay output. The number of auxiliary outputs that can be used will decrease

by one.

Models with One Control Output and a 24-VAC/VDC Power Supply (Add ACDC24 to the Model number.)

*1. If heating/cooling control mode is used, an auxiliary output is used as a control output for the cooling side. The number of auxiliary outputs that

can be used will decrease by one. Also, the signal for the control output for the cooling side will be a relay output.

*2. A current control output can be used as the transfer output. In that case, an auxiliary output is used as the control output. (This is not possible

for models without an auxiliary output.) The control output will be a relay output. The number of auxiliary outputs that can be used will decrease

by one.

Accessories (Order Separately)

USB-Serial Conversion Cable

Waterproof Packing

Current Transformers (CTs)

CX-Thermo Support Software

Note: The E5GN is supported by CX-Thermo version 4.2 and higher.

Case color Control

output

Control

mode *1

No. of

auxiliary

outputs

Detection of

heater

burnout,

SSR failure,

and heater

overcurrent

No. of event

inputs

Transfer

output *2

Communi

cations

Previous model

New model

Thermocou-

ple input

Resistance

thermome-

ter input

Black Current

output

Standard or

heating/

cooling

1 --- ---

Transfer

output using

control

output

--- --- --- E5GN-C1L-C

Case color Control

output

Control

mode *1

No. of

auxiliary

outputs

Detection of

heater

burnout,

SSR failure,

and heater

overcurrent

No. of event

inputs

Transfer

output *2

Communi

cations

Previous model

New model

Thermocou-

ple input

Resistance

thermome-

ter input

Black Current

output

Standard or

heating/

cooling

1 --- ---

Transfer

output using

control

output

--- --- --- E5GN-C1LD-

Model

E58-CIFQ1

Model

Y92S-32

Hole diameter Model

5.8 dia. E54-CT1

12.0 dia. E54-CT3

Model

EST2-2C-MV4

E5GN

Specifications

Ratings

Power supply voltage No D in model number: 100 to 240 VAC, 50/60 Hz

D in model number: 24 VAC, 50/60 Hz; 24 VDC

Operating voltage range 85% to 110% of rated supply voltage

Power

consump-

tion

E5GN

Screw terminal

block

100 to 240 VAC: 5.5 VA (max.)

24 VAC/VDC: 3 VA/2 W (max.)

E5GN-@-C

Screwless clamp

terminal block

100 to 240 VAC: 5.5 VA (max.)

24 VAC/VDC: 3 VA/2 W (max.)

Sensor input

Models with temperature inputs

Thermocouple: K, J, T, E, L, U, N, R, S, B, W, or PL II

Platinum resistance thermometer: Pt100 or JPt100

Infrared temperature sensor: 10 to 70°C, 60 to 120°C, 115 to 165°C, or 140 to 260°C

Voltage input: 0 to 50 mV

Models with analog inputs

Current input: 4 to 20 mA or 0 to 20 mA

Voltage input: 1 to 5 V, 0 to 5 V, or 0 to 10 V

Input impedance Current input: 150 Ω max., Voltage input: 1 MΩ min. (Use a 1:1 connection when connecting the ES2-HB.)

Control method ON/OFF control or 2-PID control (with auto-tuning)

Control

outputs

Relay output SPST-NO, 250 VAC, 2 A (resistive load), electrical life: 100,000 operations, minimum applicable load: 5 V,

10 mA

Voltage output

(for driving SSR) Output voltage: 12 VDC ±15% (PNP), max. load current: 21 mA, with short-circuit protection circuit

Current output 4 to 20 mA DC/0 to 20 mA DC, load: 500 Ω max., resolution: approx. 10,000

Auxiliary

outputs

Number of outputs 1 or 2 max. (Depends on the model.)

Output

specifications

Relay output: SPST-NO, 250 VAC, 2 A (resistive load), electrical life: 100,000 operations, minimum

applicable load: 5 V, 10 mA

Event

inputs

Number of inputs 2

External contact

input

specifications

Contact input: ON: 1 kΩ max., OFF: 100 kΩ min.

Non-contact input: ON: Residual voltage: 1.5 V max., OFF: Leakage current: 0.1 mA max.

Current flow: Approx. 7 mA per contact

Setting method Digital setting using front panel keys

Indication method 11-segment digital display and individual indicators (7-segment display also possible)

Character height: PV: 7.5 mm, SV: 3.6 mm

Multi SP Up to four set points (SP0 to SP3) can be saved and selected using event inputs, key operations, or serial

communications.

Bank switching Not supported

Other functions

Manual output, heating/cooling control, loop burnout alarm, SP ramp, other alarm functions, heater burnout

detection, 40% AT, 100% AT, MV limiter, input digital filter, self-tuning, temperature input shift, run/stop,

protection functions, control output ON/OFF counter, extraction of square root, MV change rate limit, logic

operations, PV/SV status display, simple program, automatic cooling coefficient adjustment

Ambient operating temperature −10 to 55°C (with no condensation or icing), for 3-year warranty: −10 to 50°C

Ambient operating humidity 25% to 85%

Storage temperature −25 to 65°C (with no condensation or icing)

E5GN

Input Ranges

Thermocouple/Platinum Resistance Thermometer (Universal Inputs)

Shaded settings are the default settings.

The applicable standards for the input types are as follows:

K, J, T, E, N, R, S, B: JIS C 1602-1995, IEC 584-1

L: Fe-CuNi, DIN 43710-1985

U: Cu-CuNi, DIN 43710-1985

W: W5Re/W26Re, ASTM E988-1990

JPt100: JIS C 1604-1989, JIS C 1606-1989

Pt100: JIS C 1604-1997, IEC 751

PL II: According to Platinel II electromotive force charts from BASF (previously Engelhard)

Models with Analog Inputs

Shaded settings are the default settings.

Input

Type

Platinum resistance

thermometer Thermocouple Infrared temperature

sensor

Analog

input

Name Pt100 JPt100 K J T E L U N R S B W PL

10 to

70°C

60 to

120

°C

115

165

°C

140

260

°C

0 to

50 mV

Temperature range (°C)

2300

1800

1700

1600

1500

1400

1300

1200

1100

1000

900

800

700

600

500

400

300

200

100

−100.0

−200.0

2300

Usable

in the

following

ranges

scaling:

−1999 to

9999 or

−199.9

to 999.9

1800

1700 1700

1300 1300 1300

850 850 850

600

500.0 500.0 500.0

400.0 400 400.0 400 400.0

260

120 165

100.0 100.0 90

100

0.0 0.0 00 00 0 0 0 0

−20.0 −100 −20.0 −100

−200 −199.9 −199.9 −200 −200 −199.9 −200 −200 −199.9 −200

Setting

number 012345 6 7 8 9 10 11 12 13 14 15 16 17 18 24 25 19 20 21 22 23

Input Type Current Voltage

Input specification 4 to 20 mA 0 to 20 mA 1 to 5 V 0 to 5 V 0 to 10 V

Setting range Usable in the following ranges by scaling:

−1999 to 9999, −199.9 to 999.9, −19.99 to 99.99 or −1.999 to 9.999

Setting number 01234

E5GN

Alarm Outputs

Each alarm can be independently set to one of the following 13 alarm types. The default is 2: Upper limit.

Auxiliary outputs are allocated for alarms. ON delays and OFF delays (0 to 999 s) can also be specified.

Note: For models with heater burnout, SSR failure, and heater overcurrent detection, alarm 1 will be an OR output of the alarm selected from the

following alarm types and the alarms for heater burnout, SSR failure, and heater overcurrent. To output only a heater burnout alarm, SSR

failure alarm, and heater overcurrent alarm for alarm 1, set the alarm type to 0 (i.e., no alarm function).

*1. With set values 1, 4 and 5, the upper and lower limit values can

be set independently for each alarm type, and are expressed as

“L” and “H.”

*2. Set value: 1, Upper- and lower-limit alarm

*3. Set value: 4, Upper- and lower-limit range

*4. Set value: 5, Upper- and lower-limit with standby sequence

For Upper- and Lower-Limit Alarm Described Above

•Case 1 and 2

Always OFF when the upper-limit and lower-limit hysteresis

overlaps.

•Case 3: Always OFF

*5. Set value: 5, Upper- and lower-limit with standby sequence

Always OFF when the upper-limit and lower-limit hysteresis

overlaps.

*6. Refer to the E5CN/E5AN/E5EN/E5GN Digital Temperature

Controllers User's Manual Basic Type (Cat. No. H156) for

information on the operation of the standby sequence.

*7. Refer to the E5CN/E5AN/E5EN/E5GN Digital Temperature

Controllers User's Manual Basic Type (Cat. No. H156) for

information on the loop burnout alarm (LBA).

*8. Refer to the E5CN/E5AN/E5EN/E5GN Digital Temperature

Controllers User's Manual Basic Type (Cat. No. H156) for

information on the PV change rate alarm.

Set value Alarm type

Alarm output operation

Description of function

When alarm value

X is positive

When alarm value

X is negative

0 Alarm function OFF Output OFF No alarm

1 *1 Upper- and lower-limit *2Set the deviation in the set point by setting the alarm

upper limit (H) and alarm lower limit (L).

2 Upper-limit Set the upward deviation in the set point by setting

the alarm value (X).

3 Lower-limit Set the downward deviation in the set point by setting

the alarm value (X).

4 *1 Upper- and lower-limit range *3Set the deviation in the set point by setting the alarm

upper limit (H) and alarm lower limit (L).

5 *1Upper- and lower-limit with

standby sequence *5

*4A standby sequence is added to the upper- and

lower-limit alarm (1). *6

6 Upper-limit with standby sequence A standby sequence is added to the upper-limit alarm

(2). *6

7 Lower-limit with standby sequence A standby sequence is added to the lower-limit alarm

(3). *6

8 Absolute-value upper-limit The alarm will turn ON if the process value is larger

than the alarm value (X) regardless of the set point.

9 Absolute-value lower-limit The alarm will turn ON if the process value is smaller

than the alarm value (X) regardless of the set point.

10 Absolute-value upper-limit with

standby sequence

A standby sequence is added to the absolute-value

upper-limit alarm (8). *6

11 Absolute-value lower-limit with

standby sequence

A standby sequence is added to the absolute-value

lower-limit alarm (9). *6

12 LBA (alarm 1 type only) --- *7

13 PV change rate alarm --- *8

OFF SP

OFF 0

OFF

OFF 0

OFF

H < 0, L > 0

⏐H⏐ < ⏐L⏐

Case 1

H > 0, L < 0

⏐H⏐ > ⏐L⏐

Case 2

H < 0, L < 0

H < 0, L > 0

⏐H⏐ ≥ ⏐L⏐

H > 0, L < 0

⏐H⏐ ≤ ⏐L⏐

Case 3 (Always ON)

LHSP

Case 1

LHSP

Case 2

LHSP

HSP

Case 3 (Always OFF)

H < 0, L > 0

⏐H⏐ < ⏐L⏐

H > 0, L < 0

⏐H⏐ > ⏐L⏐

H < 0, L < 0

H < 0, L > 0

⏐H⏐ ≥ ⏐L⏐

H > 0, L < 0

⏐H⏐ ≤ ⏐L⏐

E5GN

Characteristics

*1. The indication accuracy of K thermocouples in the −200 to 1300°C range, T and N thermocouples at a temperature of −100°C max., and U

and L thermocouples at any temperatures is ±2°C ±1 digit max. The indication accuracy of the B thermocouple at a temperature of 400°C max.

is not specified. The indication accuracy of B thermocouples in the 400 to 800°C range is ±3°C max. The indication accuracy of the R and S

thermocouples at a temperature of 200°C max. is ±3°C ±1 digit max. The indication accuracy of W thermocouples is ±0.3 of PV or ±3°C,

whichever is greater, ±1 digit max. The indication accuracy of PL II thermocouples is ±0.3 of PV or ±2°C, whichever is greater, ±1 digit max.

*2. Ambient temperature: −10°C to 23°C to 55°C, Voltage range: −15% to 10% of rated voltage

*3. K thermocouple at −100°C max.: ±10° max.

*4. “EU” stands for Engineering Unit and is used as the unit after scaling. For a temperature sensor, the EU is °C or °F.

*5. When robust tuning (RT) is ON, the differential time is 0.0 to 999.9 (in units of 0.1 s).

*6. External serial communications (RS-232C or RS-485) and cable communications for the Setup Tool can be used at the same time.

Indication accuracy

Thermocouple: *1

(±0.3% of indicated value or ±1°C, whichever is greater) ±1 digit max.

Platinum resistance thermometer input:

(±0.2% of indicated value or ±0.8°C, whichever is greater) ±1 digit max.

Analog input:

±0.2% FS ±1 digit max.

CT input:

±5% FS ±1 digit max.

Influence of temperature *2

Thermocouple input (R, S, B, W, PL II):

(±1% of PV or ±10°C, whichever is greater) ±1 digit max.

Other thermocouple input: *3

(±1% of PV or ±4°C, whichever is greater) ±1 digit max.

Platinum resistance thermometer input:

(±1% of PV or ±2°C, whichever is greater) ±1 digit max.

Analog input:

(±1%FS) ±1 digit max.

Influence of voltage *2

Input sampling period 250 ms

Hysteresis Models with thermocouple/platinum resistance thermometer input (universal input): 0.1 to 999.9 EU (in units of 0.1 EU) *4

Models with analog input: 0.01 to 99.99% FS (in units of 0.01% FS)

Proportional band (P) Models with thermocouple/platinum resistance thermometer input (universal input): 0.1 to 999.9 EU (in units of 0.1 EU) *4

Models with analog input: 0.1 to 999.9% FS (in units of 0.1% FS)

Integral time (I) 0 to 3999 s (in units of 1 s)

Derivative time (D) 0 to 3999 s (in units of 1 s) *5

Control period 0.5, 1 to 99 s (in units of 1 s)

Manual reset value 0.0 to 100.0% (in units of 0.1%)

Alarm setting range −1999 to 9999 (decimal point position depends on input type)

Affect of signal source

resistance

Thermocouple: 0.1°C/Ω max. (100 Ω max.)

Platinum resistance thermometer: 0.1°C/Ω max. (10 Ω max.)

Insulation resistance 20 MΩ min. (at 500 VDC)

Dielectric strength 2,300 VAC, 50 or 60 Hz for 1 min (between terminals with different charge)

Vibration

resistance

Malfunction 10 to 55 Hz, 20 m/s2 for 10 min each in X, Y, and Z directions

Destruction 10 to 55 Hz, 0.75-mm single amplitude for 2 hrs each in X, Y, and Z directions

Shock

resistance

Malfunction 100 m/s2, 3 times each in X, Y, and Z directions

Destruction 300 m/s2, 3 times each in X, Y, and Z directions

Weight Controller: Approx. 90 g, Mounting Bracket: Approx. 10 g

Degree of protection Front panel: IP66, Rear case: IP20, Terminals: IP00

Memory protection Non-volatile memory (number of writes: 1,000,000 times)

Setup Tool CX-Thermo version 4.2 or higher

Setup Tool port Provided on the side of the E5GN. Connect this port to the computer when using the Setup Tool. An E58-CIFQ1 USB-Serial

Conversion Cable is required to connect the computer to the port on the side of the E5GN. *6

Standards

Approved

standards UL 61010-1, CSA C22.2 No. 1010-1

Conformed

standards EN 61010-1 (IEC 61010-1): Pollution level 2, overcurrent category II

EMC

EMI: EN 61326

Radiated Interference Electromagnetic Field Strength: EN 55011 Group 1, class A

Noise Terminal Voltage: EN 55011 Group 1, class A

EMS: EN 61326

ESD Immunity: EN 61000-4-2

Electromagnetic Field Immunity: EN 61000-4-3

Burst Noise Immunity: EN 61000-4-4

Conducted Disturbance Immunity: EN 61000-4-6

Surge Immunity: EN 61000-4-5

Power Frequency Magnetic Field Immunity: EN 61000-4-8

Voltage Dip/Interrupting Immunity: EN 61000-4-11

E5GN

USB-Serial Conversion Cable

Note: A driver must be installed in the personal computer. Refer to

installation information in the operation manual for the

Conversion Cable.

Communications Specifications

*The baud rate, data bit length, stop bit length, and vertical parity can

be individually set using the Communications Setting Level.

Current Transformer (Order Separately)

Ratings

Heater Burnout Alarms, SSR Failure

Alarms, and Heater Overcurrent Alarms

*1. For heater burnout alarms, the heater current will be measured

when the control output is ON, and the output assigned to the

alarm 1 function will turn ON if the heater current is lower than the

set value (i.e., heater burnout detection current value).

*2. For SSR failure alarms, the heater current will be measured when

the control output is OFF, and the output assigned to the alarm 1

function will turn ON if the heater current is higher than the set

value (i.e., SSR failure detection current value).

*3. For heater overcurrent alarms, the heater current will be

measured when the control output is ON, and the output assigned

to the alarm 1 function will turn ON if the heater current is higher

than the set value (i.e., heater overcurrent detection current

value).

Electrical Life Expectancy Curve for

Relays (Reference Values)

Applicable OS Windows 2000, XP, or Vista

Applicable software CX-Thermo version 4 or higher

Applicable models E5AN/E5EN/E5CN/E5CN-U/E5AN-H/

E5EN-H/E5CN-H/E5GN

USB interface standard Conforms to USB Specification 1.1.

DTE speed 38400 bps

Connector

specifications

Computer: USB (type A plug)

Temperature Controller: Setup Tool port

(on bottom of Controller)

Power supply Bus power (Supplied from USB host

controller.)

Power supply voltage 5 VDC

Current consumption 70 mA

Ambient operating

temperature 0 to 55°C (with no condensation or icing)

Ambient operating

humidity 10% to 80%

Storage temperature −20 to 60°C (with no condensation or

icing)

Storage humidity 10% to 80%

Altitude 2,000 m max.

Weight Approx. 100 g

Transmission line

connection method

RS-485: Multipoint

RS-232C: Point-to-point

Communications RS-485 (two-wire, half duplex), RS-232C

Synchronization

method Start-stop synchronization

Protocol CompoWay/F, SYSWAY, or Modbus

Baud rate 1200, 2400, 4800, 9600, 19200, 38400, or

57600 bps

Transmission code ASCII

Data bit length *7 or 8 bits

Stop bit length *1 or 2 bits

Error detection

Vertical parity (none, even, odd)

Frame check sequence (FCS) with SYSWAY

Block check character (BCC) with

CompoWay/F or CRC-16 Modbus

Flow control None

Interface RS-485, RS-232C

Retry function None

Communications

buffer 217 bytes

Communications

response wait time

0 to 99 ms

Default: 20 ms

Dielectric strength 1,000 VAC for 1 min

Vibration resistance 50 Hz, 98 m/s2

Weight E54-CT1: Approx. 11.5 g,

E54-CT3: Approx. 50 g

Accessories

(E54-CT3 only)

Armatures (2)

Plugs (2)

CT input

(for heater current

detection)

Models with detection for single-phase

heaters: One input

Maximum heater current 50 A AC

Input current indication

accuracy ±5% FS ±1 digit max.

Heater burnout alarm

setting range *1

0.1 to 49.9 A (in units of 0.1 A)

Minimum detection ON time: 100 ms

SSR failure alarm

setting range *2

0.1 to 49.9 A (in units of 0.1 A)

Minimum detection OFF time: 100 ms

Heater overcurrent

alarm setting range *3

0.1 to 49.9 A (in units of 0.1 A)

Minimum detection ON time: 100 ms

500

300

200

100

0.1 0.2 0.50.3 1 2 3 5 10

E5GN

250 VAC, 30 VDC

(resistive load)

cosφ = 1

Switching current (A)

Life (× 104 operations)

E5GN

External Connections

•A voltage output (control output, for driving SSR) is not electrically

insulated from the internal circuits. When using a grounding

thermocouple, do not connect any of the control output terminals to

ground. (If the control output terminals are connected to ground,

errors will occur in the measured temperature values as a result of

leakage current.)

E5GN Controllers

Wiring

E5GN

Models with Screw Terminal Blocks (M3 Screws)

E5GN-@-C

Models with Screwless Clamp Terminal Blocks

789

10 11 12

123456

Relay output

250 VAC, 2 A (resistive load)

Voltage output (for driving SSR)

12 VDC, 21 mA

Current output

0 to 20 mA DC

4 to 20 mA DC

Load: 500 Ω max.

BBA

EV1

EV2

DO NOT

USE

DO NOT

USE

DO NOT

USE

DO NOT

USE

13 14

Terminal Arrangement

Models with Screw

Terminal Blocks

Models with Screwless

Clamp Terminal Blocks

123456

7 8 9 10 11 12

123456

7 8 9 10 11 12

• 100 to 240 VAC

• 24 VAC/VDC (no polarity)

Control output 1

250 VAC, 2 A (resistive load)

Relay outputs

The E5@N-@@@T@ is set for a K thermocouple

(input type of 5) by default. If a difference sensor is

used, an input error (s.err) will occur. Check the

setting of the input type parameter.

Auxiliary outputs 1 and 2

+Control

output 1

Input power

supply Auxiliary

output 1

Universal TC/Pt input

Analog input

Event input

CT input

RS-485

communications

RS-232C

communications

Auxiliary output 2

connection screws

Auxiliary

output 2

A heater burnout alarm, heater short

alarm, heater overcurrent alarm, or

input error is sent to the output to

which the alarm 1 function is assigned.

B (+) A (−)

SGRD

M3 Screw Terminal Blocks

• Crimp terminal shape: Forked or round

• Tightening torque for all terminals: 0.5 N•m

5.8 mm max.

Models with Screwless Clamp Terminal Blocks

•

Wire stripping: 10 mm

•

Ferrules: 8 to 12 mm

0.8 to 1.4 mm

10 mm 8 to 12 mm

E5GN

Nomenclature

Dimensions (Unit: mm)

Accessories (Order Separately)

USB-Serial Conversion Cable

Operation indicators

Level Key

Temperature unit

No.1 display

No. 2 display

Up Key

Mode Key Down Key

Operation indicators

The front panel is the same for the E5GN.

22 22

44.8

35 24

Waterproof Packing (Provided)

Flush Mounting Adapter (Provided)

22.2+0.3

45+0.6

40 min.

(48 × number of units − 2.5)+1.0

Group mounting does not allow waterproofing.

Panel Cutout

Mounted Separately Group Mounted

22.2+0.3

E5GN

Models with Screw

Terminal Blocks

•Recommended panel thickness is 1 to 5 mm.

•Group mounting is not possible in the vertical

direction. (Maintain the specified mounting space

between Controllers.)

•To m o unt the Controller so that it is waterproof, insert

the waterproof packing onto the Controller.

•When two or more Controllers are mounted, make

sure that the surrounding temperature does not

exceed the allowable operating temperature

specified in the specifications.

100

22 22

44.8

35 24

Waterproof Packing (Provided)

Flush Mounting Adapter (Provided)

22.2+0.3

45+0.6

40 min.

(48 × number of units − 2.5)+1.0

Panel Cutout

Mounted Separately Group Mounted

22.2+0.3

Group mounting does not allow waterproofing.

E5GN-@-C

Models with

Screwless Clamp

Terminal Blocks

•Recommended panel thickness is 1 to 5 mm.

•Group mounting is not possible in the vertical

direction. (Maintain the specified mounting space

between Controllers.)

•When two or more Controllers are mounted, make

sure that the surrounding temperature does not

exceed the allowable operating temperature

specified in the specifications.

(2,100)

250 1,765

USB connector (type A plug) Serial connector

LED indicator

(

)

LED indicator (SD)

E58-

E5GN

Current Transformers

Order the Waterproof Packing separately if it becomes lost or damaged.

The Waterproof Packing can be used to achieve an IP66 degree of protection.

(Deterioration, shrinking, or hardening of the waterproof packing may occur depending on the

operating environment. Therefore, periodic replacement is recommended to ensure the level of

waterproofing specified in IP66. The time for periodic replacement depends on the operating

environment. Be sure to confirm this point at your site. Consider one year a rough standard.

OMRON shall not be liable for the level of water resistance if the customer does not perform

periodic replacement.)

The Waterproof Packing does not need to be attached if a waterproof structure is not required.

Waterproof Packing

Y92S-32 (for DIN 48 × 24)

E54-CT3 Accessory

•Armature

15 5.8 dia.

25 3

10.5

2.8

7.5

Two, 3.5 dia.

40 × 40

12 dia.

2.36 dia.

Two, M3 (depth: 4)

Approx. 3 dia.

(22)

Approx. 6 dia.

Plug

Armature

Lead

E54-CT1

E54-CT3

Connection Example

•Plug

E54-CT1

Thru-current (Io) vs. Output Voltage

(Eo) (Reference Values)

Maximum continuous heater current: 50 A (50/60 Hz)

Number of windings: 400±2

Winding resistance: 18±2 Ω

Thru-current (Io) A (r.m.s.)

1 10 100 mA 1 10 100

1,000 A

Output voltage (Eo) V (r.m.s.)

100 V

50 Hz

Distortion

factor 10%

100 Ω

RL = 10 Ω

∞

100 mV

100 µV

1 kΩ

E54-CT3

Thru-current (Io) vs. Output Voltage

(Eo) (Reference Values)

Maximum continuous heater current: 120 A (50/60 Hz)

(Maximum continuous heater current for the

Temperature Controller is 50 A.)

Number of windings: 400±2

Winding resistance: 8±0.8 Ω

1 kΩ

100 Ω

50 Ω

RL = 10 Ω

500 Ω

∞

Distor-

tion

factor

10%

Thru-current (Io) A (r.m.s.)

1 10 100 mA 1 10 100

1,000 A

Output voltage (Eo) V (r.m.s.)

100 V

50 Hz

100 mV

100 µV

Terms and Conditions of Sale

1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed

part of all quotes, agreements, purchase orders, acknowledgments, price lists,

catalogs, manuals, brochures and other documents, whether electronic or in

writing, relating to the sale of products or services (collectively, the "Products")

by Omron Electronics LLC and its subsidiary companies (“Omron”). Omron

objects to any terms or conditions proposed in Buyer’s purchase order or other

documents which are inconsistent with, or in addition to, these Terms.

2. Prices; Payment Terms. All prices stated are current, subject to change with-

out notice by Omron. Omron reserves the right to increase or decrease prices

on any unshipped portions of outstanding orders. Payments for Products are

due net 30 days unless otherwise stated in the invoice.

3. Discounts. Cash discounts, if any, will apply only on the net amount of invoices

sent to Buyer after deducting transportation charges, taxes and duties, and will

be allowed only if (i) the invoice is paid according to Omron’s payment terms

and (ii) Buyer has no past due amounts.

4. Interest. Omron, at its option, may charge Buyer 1-1/2% interest per month or

the maximum legal rate, whichever is less, on any balance not paid within the

stated terms.

5. Orders. Omron will accept no order less than $200 net billing.

6. Governmental Approvals. Buyer shall be responsible for, and shall bear all

costs involved in, obtaining any government approvals required for the impor-

tation or sale of the Products.

7. Taxes. All taxes, duties and other governmental charges (other than general

real property and income taxes), including any interest or penalties thereon,

imposed directly or indirectly on Omron or required to be collected directly or

indirectly by Omron for the manufacture, production, sale, delivery, importa-

tion, consumption or use of the Products sold hereunder (including customs

duties and sales, excise, use, turnover and license taxes) shall be charged to

and remitted by Buyer to Omron.

8. Financial. If the financial position of Buyer at any time becomes unsatisfactory

to Omron, Omron reserves the right to stop shipments or require satisfactory

security or payment in advance. If Buyer fails to make payment or otherwise

comply with these Terms or any related agreement, Omron may (without liabil-

ity and in addition to other remedies) cancel any unshipped portion of Prod-

ucts sold hereunder and stop any Products in transit until Buyer pays all

amounts, including amounts payable hereunder, whether or not then due,

which are owing to it by Buyer. Buyer shall in any event remain liable for all

unpaid accounts.

9. Cancellation; Etc. Orders are not subject to rescheduling or cancellation

unless Buyer indemnifies Omron against all related costs or expenses.

10. Force Majeure. Omron shall not be liable for any delay or failure in delivery

resulting from causes beyond its control, including earthquakes, fires, floods,

strikes or other labor disputes, shortage of labor or materials, accidents to

machinery, acts of sabotage, riots, delay in or lack of transportation or the

requirements of any government authority.

11. Shipping; Delivery. Unless otherwise expressly agreed in writing by Omron:

a. Shipments shall be by a carrier selected by Omron; Omron will not drop ship

except in “break down” situations.

b. Such carrier shall act as the agent of Buyer and delivery to such carrier shall

constitute delivery to Buyer;

c. All sales and shipments of Products shall be FOB shipping point (unless oth-

erwise stated in writing by Omron), at which point title and risk of loss shall

pass from Omron to Buyer; provided that Omron shall retain a security inter-

est in the Products until the full purchase price is paid;

d. Delivery and shipping dates are estimates only; and

e. Omron will package Products as it deems proper for protection against nor-

mal handling and extra charges apply to special conditions.

12. Claims. Any claim by Buyer against Omron for shortage or damage to the

Products occurring before delivery to the carrier must be presented in writing

to Omron within 30 days of receipt of shipment and include the original trans-

portation bill signed by the carrier noting that the carrier received the Products

from Omron in the condition claimed.

13. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the

Products will be free from defects in materials and workmanship for a period of

twelve months from the date of sale by Omron (or such other period expressed

in writing by Omron). Omron disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION,

EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABIL-

ITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS.

BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR

INTENDED USE. Omron further disclaims all warranties and responsibility of

any type for claims or expenses based on infringement by the Products or oth-

erwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obli-

gation hereunder shall be, at Omron’s election, to (i) replace (in the form

originally shipped with Buyer responsible for labor charges for removal or

replacement thereof) the non-complying Product, (ii) repair the non-complying

Product, or (iii) repay or credit Buyer an amount equal to the purchase price of

the non-complying Product; provided that in no event shall Omron be responsi-

ble for warranty, repair, indemnity or any other claims or expenses regarding

the Products unless Omron’s analysis confirms that the Products were prop-

erly handled, stored, installed and maintained and not subject to contamina-

tion, abuse, misuse or inappropriate modification. Return of any Products by

Buyer must be approved in writing by Omron before shipment. Omron Compa-

nies shall not be liable for the suitability or unsuitability or the results from the

use of Products in combination with any electrical or electronic components,

circuits, system assemblies or any other materials or substances or environ-

ments. Any advice, recommendations or information given orally or in writing,

are not to be construed as an amendment or addition to the above warranty.

See http://www.omron247.com or contact your Omron representative for pub-

lished information.

14. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE

FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY

WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS

BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Omron Companies exceed the individual

price of the Product on which liability is asserted.

15. Indemnities. Buyer shall indemnify and hold harmless Omron Companies and

their employees from and against all liabilities, losses, claims, costs and

expenses (including attorney's fees and expenses) related to any claim, inves-

tigation, litigation or proceeding (whether or not Omron is a party) which arises

or is alleged to arise from Buyer's acts or omissions under these Terms or in

any way with respect to the Products. Without limiting the foregoing, Buyer (at

its own expense) shall indemnify and hold harmless Omron and defend or set-

tle any action brought against such Companies to the extent based on a claim

that any Product made to Buyer specifications infringed intellectual property

rights of another party.

16. Property; Confidentiality. Any intellectual property in the Products is the exclu-

sive property of Omron Companies and Buyer shall not attempt to duplicate it

in any way without the written permission of Omron. Notwithstanding any

charges to Buyer for engineering or tooling, all engineering and tooling shall

remain the exclusive property of Omron. All information and materials supplied

by Omron to Buyer relating to the Products are confidential and proprietary,

and Buyer shall limit distribution thereof to its trusted employees and strictly

prevent disclosure to any third party.

17. Export Controls. Buyer shall comply with all applicable laws, regulations and

licenses regarding (i) export of products or information; (iii) sale of products to

“forbidden” or other proscribed persons; and (ii) disclosure to non-citizens of

regulated technology or information.

18. Miscellaneous. (a) Waiver. No failure or delay by Omron in exercising any right

and no course of dealing between Buyer and Omron shall operate as a waiver

of rights by Omron. (b) Assignment. Buyer may not assign its rights hereunder

without Omron's written consent. (c) Law. These Terms are governed by the

law of the jurisdiction of the home office of the Omron company from which

Buyer is purchasing the Products (without regard to conflict of law princi-

ples). (d) Amendment. These Terms constitute the entire agreement between

Buyer and Omron relating to the Products, and no provision may be changed

or waived unless in writing signed by the parties. (e) Severability

. If any provi-

sion hereof is rendered ineffective or invalid, such provision shall not invalidate

any other provision. (f) Setoff. Buyer shall have no right to set off any amounts

against the amount owing in respect of this invoice. (g) Definitions. As used

herein, “including” means “including without limitation”; and “Omron Compa-

nies” (or similar words) mean Omron Corporation and any direct or indirect

subsidiary or affiliate thereof.

Certain Precautions on Specifications and Use

1. Suitability of Use. Omron Companies shall not be responsible for conformity

with any standards, codes or regulations which apply to the combination of the

Product in the Buyer’s application or use of the Product. At Buyer’s request,

Omron will provide applicable third party certification documents identifying

ratings and limitations of use which apply to the Product. This information by

itself is not sufficient for a complete determination of the suitability of the Prod-

uct in combination with the end product, machine, system, or other application

or use. Buyer shall be solely responsible for determining appropriateness of

the particular Product with respect to Buyer’s application, product or system.

Buyer shall take application responsibility in all cases but the following is a

non-exhaustive list of applications for which particular attention must be given:

(i) Outdoor use, uses involving potential chemical contamination or electrical

interference, or conditions or uses not described in this document.

(ii) Use in consumer products or any use in significant quantities.

(iii) Energy control systems, combustion systems, railroad systems, aviation

systems, medical equipment, amusement machines, vehicles, safety equip-

ment, and installations subject to separate industry or government regulations.

(iv) Systems, machines and equipment that could present a risk to life or prop-

erty. Please know and observe all prohibitions of use applicable to this Prod-

uct.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS

RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT

ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO

ADDRESS THE RISKS, AND THAT THE OMRON’S PRODUCT IS PROP-

ERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

2. Programmable Products. Omron Companies shall not be responsible for the

user’s programming of a programmable Product, or any consequence thereof.

3. Performance Data. Data presented in Omron Company websites, catalogs

and other materials is provided as a guide for the user in determining suitabil-

ity and does not constitute a warranty. It may represent the result of Omron’s

test conditions, and the user must correlate it to actual application require-

ments. Actual performance is subject to the Omron’s Warranty and Limitations

of Liability.

4. Change in Specifications. Product specifications and accessories may be

changed at any time based on improvements and other reasons. It is our prac-

tice to change part numbers when published ratings or features are changed,

or when significant construction changes are made. However, some specifica-

tions of the Product may be changed without any notice. When in doubt, spe-

cial part numbers may be assigned to fix or establish key specifications for

your application. Please consult with your Omron’s representative at any time

to confirm actual specifications of purchased Product.

5. Errors and Omissions. Information presented by Omron Companies has been

checked and is believed to be accurate; however, no responsibility is assumed

for clerical, typographical or proofreading errors or omissions.

OMRON ELECTRONICS LLC •

THE AMERICAS HEADQUARTERS

Schaumburg, IL USA • 847.843.7900 • 800.556.6766 • www.omron247.com

OMRON CANADA, INC. • HEAD OFFICE

Toronto, ON, Canada • 416.286.6465 • 866.986.6766 •

www.omron247.com

OMRON ELETRÔNICA DO BRASIL LTDA • HEAD OFFICE

São Paulo, SP, Brasil • 55.11.2101.6300 • www.omron.com.br

OMRON ELECTRONICS MEXICO SA DE CV • HEAD OFFICE

Apodaca, N.L. • 52.811.156.99.10 • 001.800.556.6766 •

mela@omron.com

OMRON ARGENTINA • SALES OFFICE

Cono Sur • 54.11.4783.5300

OMRON CHILE • SALES OFFICE

Santiago • 56.9.9917.3920

OTHER OMRON LATIN AMERICA SALES

54.11.4783.5300

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Note: This datasheet is provided as a guideline for selecting products. Do not use this document to operate the Unit.

Cat. No. CMS_E5GN_E_5_1 12/09 Specifica tions are subject to c hange witho ut notic e.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Omron:

E5GN-Q103TD-C-FLK AC/DC24 E5GN-Q103T-C-FLK AC100-240 E5GN-Q103TD-FLK AC/DC24 E5GN-Q1TD-C

AC/DC24 E5GN-Q1T-C AC100-240N6 E5GN-Q1TD AC/DC24 E5GN-QTD-C AC/DC24 E5GN-QT-C AC100-240N6

E5GN-QTD AC/DC24 E5GN-QT AC100-240 E5GN-R103TD-C-FLK AC/DC24 E5GN-R103T-C-FLK AC100-240

E5GN-R103TD-FLK AC/DC24 E5GN-R103T-FLK AC100-240 E5GN-R1TD-C AC/DC24 E5GN-R1T-C AC100-240N6

E5GN-R1T AC100-240 E5GN-RTD-C AC/DC24 E5GN-RT-C AC100-240N6 E5GN-RTD AC/DC24 E5GN-RT AC100-

240 E5GN-Q103T-FLK AC100-240 E5GN-R1TD-AC/DC24