FXC7000-48-S - Power-One - Datasheet.Wiki

FXC7000 AC-DC Series Data Sheet

AUG 18, 2006 revised to JAN 09, 2007 Page 1 of 4 www.power-one.com

Features

• Three-phase AC input

• Suitable for 3U or 5U height mounting

• Single-wire current share or Droop current share

• Remote voltage adjust and current monitoring

• Overtemperature, overload, and overvoltage protection

• LED supply status indicators

• Current-share control for up to 30 units

• Front panel selectable-input-range

FXC7000

Front and Rear Views

The FXC7000 Series of standalone or rack-mounted

power systems provides true AC front-end capability to

automatic test equipment, telecom, data commun-

ications, and other distributed power designs. The FXC

systems may be paralleled up to 210 kW of output power

and are intended for chassis-mounted installations with

bolted connections. These power supplies provide

excellent protection against input voltage transients.

The FXC has its fan located at the front of the supply, and

voltage adjust, indicator lights, output bussbars, and

connectors on the rear. Airflow is from the front through

the rear. Alarm, monitoring, and control signals are

floating from the main output and can be referenced to

the positive or negative output or sense line of the power

supply. The output is floating with respect to the chassis

and may be used as a positive or negative polarity

supply.

The FXC7000 Series meets international safety

requirements and is CE Marked to the Low Voltage

Directive. This series operates on three-phase European

voltages as well as (up to) 480VAC, delta or wye.

Distributed Power Front-End

Description

Chassis-Mountable Model

MODEL OUTPUT INPUT VOLTAGE RANGE ADJUSTMENT MAXIMUM OUTPUT LINE LOAD INITIAL SETTING

VOLTAGE 3-PHASE (VAC) RANGE CURRENT REGULATION REGULATION (NOTE 1) ACCURACY

FXC7000-48-S (NOTE 2) 48V 180 to 264 or 342 to 528 45.6V to 50.4V 145A 0.15% 0.2% 47.90V to 48.10V

NOTES: 1) With Remote Sense connected.

2). User-selectable input voltage ranges

Input Specifications

PARAMETER DESCRIPTION/CONDITIONS MIN NOM MAX UNITS

Input Voltage - AC 3-phase delta low input range, nominal. 200 240 VAC

3-phase delta high input range, nominal. 380 480

Continuous deviation from the above nominals. -10 +10 %

Input Current Per phase at full rated load. FXC7000 at 180 VAC: 30 ARMS

Inrush Surge Current Internally limited. Vin = 264VAC (one cycle). 25° C: 30 APK

Vin = 528VAC (one cycle). 25° C: 15

Input Frequency AC input. 50 60 Hz

Hold-up Time After last AC line peak at full power. 208 VAC: 17 ms

400 VAC: 13

Operating Frequency Switching frequency, fixed. 100 kHz

Power Factor 0.90 W/VA

FXC7000 AC-DC Series Data Sheet

AUG 18, 2006 revised to JAN 09, 2007 Page 2 of 4 www.power-one.com

Output Specifications

PARAMETER DESCRIPTION/CONDITIONS MIN NOM MAX UNITS

Output Voltage An additional 1.0 Volt is provided to the output terminals to provide for 45.6 48 50.4 V

Adjustment Range load lead losses.

Output Power Continuous duty rating. 7000 Watts

Output Current Continuous duty rating. 145 A

Efficiency Full rated load (208Vac). 88 91 %

Regulation Load, Maximum deviation with 0 to 100% load change:

With Remote Sense connected: 0.2

With Remote Sense not connected: 0.75 %

Utilizing Droop Current Share: 2.0

Line, Under all specified operating conditions. 0.2

Ripple & Noise Measured at mating connector w/ 0.01µF + 10µF Tant.

20 MHz BW: 1 % p-p

100 MHz BW: 2

Overshoot / Undershoot Output voltage overshoot/undershoot at turn-on. 0 %

Minimum Loads Minimum loading required to maintain regulation. 0 A

Transient Response Maximum recovery time, to within 1% of initial set Time: 800 µs

point due to a 25% load change, 1A/µS. Deviation: 3.2 %

Turn-On Delay Time required for initial output voltage stabilization after power-up. 3 s

Turn-on Rise Time Time required for output voltage to rise from 10% to 90%. 100 ms

Interface Signals and Internal Protection

PARAMETER (NOTE 1,2) DESCRIPTION/CONDITIONS MIN NOM MAX UNITS

AC Power Fail Warning Warning provided prior to Vout dropping 5% after loss of AC input. 4 ms

Auxiliary Power Output voltage - diode isolated. Inclusive of line, load, and initial tolerances. 11.6 12.0 12.4 V

Output current. 500 mA

Current Monitor Monitor output current over a compliance range of 0~10V.

Normal output: 0.10 mA/A

Total error current: 0.5 0.5 mA

Current Share Static sharing deviation as a percent of full-load rating Active: 5 %

for loads >10%. Passive: 10

Input Range Select Status Maximum signal resistance in high input voltage range selection. 0.10 ⍀

Loss of Phase Warning Warning provided prior to protective reduction in current limit. 500 ms

Output Inhibit Voltage required to enable supply (0.5 mA sink). (NOTE 3) 1.0 V

Output Interlock Voltage required to enable supply (6 mA sink). (NOTE 3) 1.0 V

Output Overload Protection Straight line current limit (above approx. 5V Vout). 149 156 A

Output Overload Warning Signal level on overload. 2.2 V

Output Short Circuit Protection Occurs on overload when Vout is below approx. 5V. Iavg: 25 90 A

May operate in burst-mode.

Output Voltage Fault Signal Deviation from adjusted Vout that is considered as a fault. ±3 ±4 ±5 %

Output Voltage Margin Output voltage swing available through Margin pin (analog). ±4.8 ±5.0 ±5.2 %

Overtemperature/ Time between fault warning and shutdown. 100 ms

Fan Failure Warning Latching shutdown.

Overvoltage Protection Latch style overvoltage protection. 55.2 57.6 60.0 V

Power Supply Present Signal Resistance to logic ground upon insertion of supply. 1000 ⍀

Remote Sense Maximum load lead loss compensation (round trip). 1.0 V

NOTES: 1) All logic outputs listed below feature a standard active pull-down output with 0.4V max at 40 mA sink capability, and a 100k pull-up to 5V.

2) In addition to those listed below, signals and front-panel LEDs are provided to indicate: overtemperature/fan fault, AC phase

imbalance, output good, interlock open, and supply inhibited. The FXP also provides 4 LED’s indicating output loading.

3) Both signals must be pulled to logic ground for the unit to operate. Enables are 100% redundant internally for applications where redundant inhibit is desirable.

Contact factory for additional design details.

FXC7000 AC-DC Series Data Sheet

AUG 18, 2006 revised to JAN 09, 2007 Page 3 of 4 www.power-one.com

Safety, Regulatory, and EMI Specifications

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Agency Approvals UL60950/CSA60950-00 (cULus), IEC60950 3rd Edition, EN60950 (TÜV),

CE marked for the Low Voltage Directive

Electromagnetic Interference FCC CFR title 47 Part 15 Sub-Part B - Conducted. A

EN55022 / CISPR 22 Conducted. A Class

ESD Susceptibility Per EN61000-4-2, level 4. 8 kV

Radiated Susceptibility Per EN61000-4-3, level 3. 10 V/M

EFT/Burst Per EN61000-4-4, level 4. ±4 kV

Input Transient Protection Per EN61000-4-5 Line-to-Line: 4 kV

Line-to-Ground: 3

Voltage Sag Immunity Per SEMI F47-0200 FXC/FXP6000 Pending

Leakage Current Per UL60950 and FXC7000 at 240 VAC, 60 Hz: 5

EN60950: FXC7000 at 400 VAC, 50 Hz: 7 mA

FXC7000 at 480 VAC, 60 Hz: 10

Environmental Specifications

PARAMETER CONDITIONS/DESCRIPTION MIN NOM MAX UNITS

Altitude Operating. 10k ASL Ft.

Non-Operating. 40k

Operating Temperature At 100% load: 0 40 °C

At 50% load: 70

Storage Temperature -40 85 °C

Temperature Coefficient 0°C to 70°C (after 15-minute warm-up). .02 %/°C

Relative Humidity Non-Condensing. 95 %RH

Shock Operating: half-sine 10 ms, 3 axis +20 GPK

Non-operating: half-sine 10 ms, 3 axis +40

Vibration Operating: swept sine 5-2000-5 Hz, 5-32 Hz, 0.02îDA, 32-2000 Hz 1 GPK

Non-operating: random 10-2000 Hz 6.15 Grms

Airflow Airflow provided through the supply from front to rear. 155 cfm

4.4 m3/min

555 lfm

2.8 m/s

Weight 27 lb

12 kg

NUCLEAR AND MEDICALAPPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components

in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective

divisional president of Power-One, Inc.

TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the

date manufactured. Specifications are subject to change without notice.

FXC7000 AC-DC Series Data Sheet

AUG 18, 2006 revised to JAN 09, 2007 Page 4 of 4 www.power-one.com

2 PL

15.17"

(385.3mm)

INSULATOR

BLOCK

10.260"

(260.6mm)

7.705"

(195.7mm)

3.510"

(89.2mm)

0.955"

(24.3mm)

6.850"

(174mm)

4.24"

(107.6mm)

0.53"

(13.4mm)

0.480"

(12.2mm)

1.22"

(31.1mm)

4.480"

(113.8mm)

DIA 0.25"

(6.4mm)

0.70"

(17.9mm)

0.955"

(24.3mm)

3.510"

(89.2mm)

13.455"

(341.8mm)

0.20"

(5.1mm)

7.705"

(195.7mm)

1.10"

(28mm)

2 PL 2 PL

2 PL

3.60"

(91.5mm)

1.100" (27.9mm)

5.42"

(137.7mm)

AA A A

AAA

MAINTAIN 25 SQ IN MIN

FREE AREA (FRONT AND

REAR) FOR AIR COOLING

BOTTOM VIEW

SIDE VIEW

REAR VIEW

FOR MOUNTING, USE M4 X 0.7 SCREWS,

8PL (MARKED A) ON SIDE OR BOTTOM

WITH MAXIMUM PENETRATION 3.8mm.

RECOMMENDED MOUNTING TORQUE

10.5 INCH LBS. (0.64N/M)

<--AIRFLOW

0.85"

(21.6mm)

1.10"

(27.9mm)

SIGNAL

Vadj

DC OUTPUT

POS

NEG

AC INPUT

VOLTAGE ADJUST POT

M4 THREAD

10mm

13mm

26-PIN CONNECTOR

AMP PN: 749030-1

PIN 1

0.06 (1.7) 2 PL

5 LED INDICATORS

26 19

CENTER-TO-CENTER

MATING CONNECTOR:

CONNECTOR SHELL...

AMP PN 748365-1

CONTACTS...

AMP PN 748333-2

FRONT VIEW

5.00"

(127mm)

8.00"

(203.2mm)

INPUT VOLTAGE RANGE

SELECT MODULE

ROTATE 180 DEGREES FOR 240 VAC

INPUT VOLTAGE

DISPLAY CUTOUT

480VAC

FXC7000 OVERALL SIZE: 15.17" x 8.00" x 5.00" (385.3mm x 203.2mm x 127.0mm)