SERIES Amplifier Built-in Robust Photoelectric Sensor EQ-20 PHOTOELECTRIC SENSORS RX EX-40 EQ-30 Advanced Sensor Technology Conforming to EMC Directive (Excluding RX2, RX3 and RX4) Waterproof Robust Test Input The sensor can be hosed down because of its IP67 construction. The equipment on which the sensor is mounted can be washed without any problem. The enclosure is robust as it is made of die-cast zinc alloy. Convenient for operation check before start-up. (Excluding the RX2 models) CY RX-LS200 RX Amplifier Built-in Type Marked The sensor operation is checked by interrupting the emission repeatedly and confirming that the output changes accordingly. Test input OFF EX Sensing output Note: However, take care that if it is exposed to water splashes during operation, it may detect a water drop itself. PX-2 ON Automatic Interference Prevention Function (Retroreflective and Diffuse Reflective Type Sensors Only) RT-610 Two sensors can be mounted side by side because of the automatic interference prevention function. (Excluding the RX2 models) There is no problem even if the beam of the adjoining sensor is incident. 248 ON OFF Normal Abnormal APPLICATIONS Detecting person entering stacker crane path Sensing transparent sheet Confirming car position at parking garage PHOTOELECTRIC SENSORS RX EQ-20 RX-PRV500 RX4-M5 RX2-PRVM2 RX-M10 RX... Standard Type RX2... DC 2-wire Type RX3... Intelligent Type * Wide variety * Wiring reduced by 1/3 Wiring can be completed by using only two, instead of three wires. * Self-diagnosis function for internal circuit In addition to the beam intensity check, the built-in microcomputer self-diagnoses the internal circuit and detects a circuit failure, should it occur. Two wires Longest range: 50m Standard (Infrared).........................10m Long sensing range (Infrared)....... 50m Visible light (Red)............................ 2m Visible light (Green).................. 500mm Diffuse reflective type Sensing object Longest range: 700mm Long sensing range (Infrared).... 700mm Wide-view (Infrared)................... 300mm Visible light (Red)....................... 200mm Retroreflective type Longest range: 5m For specular object sensing (with polarizing filters, red) .. 0.1 to 3m For transparent object sensing (with polarizing filters, red) ..... 500mm Long sensing range (Infrared) .............................. 0.1 to 5m The following parts 1 to 6 are monitored constantly. * Power supply cost: reduced to 1/30 or less Current consumption: 1mA or less An additional power supply for the sensors is not required. 3-wire type 2-wire type Wiring is time-consuming Wiring is simple for the 3-wire sensors with only two wires. and an additional power supply is required. Additional power supply 2Amplifier circuit 1 3 Output Receiving Microelement computer circuit AMP 1 4 Receiving element failure Emitting LED failure 2 5 Amplifier failure Emitting circuit failure 6 Sensing output Output transistor 5Oscillation circuit wire disconnected failure 6 Emitting element Indication of abnormal conditions 6 Output wire * Operation indicator (red) blinks. * Self-diagnosis output is ON. 3 RX4... Heavy Duty Type * Durable against oil IP67g (JEM) protection has been achieved by fluorine resin coating on the enclosure and by using oil resistant protective tube. This sensor can be used in a harsh environment. IP67g (JEM) PLC RT-610 Thru-beam type Amplifier Built-in Type RX RX-LS200 Sensing machine tools EX Counting cans Cover (Polyethersulphone) PLC Enclosure: Fluorine resin coating Lens: Polyalylate Oil resistant cable PX-2 Detecting engines CY RX-M50 EX-40 EQ-30 RX3-M10 Oil resistant protective tube 249 ORDER GUIDE Thru-beam Thru-beam Diffuse reflective Retroreflective Thru-beam Diffuse reflective Retroreflective Thru-beam Diffuse reflective Retroreflective RX3 (Intelligent type) RX2 (DC 2-wire type) RX (Standard type) Type RX4 (Heavy duty type) PHOTOELECTRIC SENSORS EQ-20 EQ-30 EX-40 RX-LS200 RX Amplifier Built-in Type CY EX RX Appearance Sensing range Model No. Long sensing range For mark sensing RX-M10 10m Infrared 50m 500mm Green RX-500G 0.1 to 3m (Note) Red (with polarizing filters) For transparent object sensing 0.1 to 5m (Note) Infrared (long sensing range) Wide-view RX-D300 300mm RX-D200R 200mm RX2-M5 5m Infrared Red (with polarizing filters) RX2-PRVM2 0.1 to 2m (Note) Infrared RX2-D300 300mm 10m Infrared Red (with polarizing filters) 0.1 to 3m (Note) For transparent object sensing RX3-PRVM3 RX3-D700 700mm 2m cable length Infrared RX3-M10 RX3-PRV500 500mm (Note) Infrared RX-RVM5 RX-D700 700mm Red RX-PRVM3 RX-PRV500 500mm (Note) Infrared RX-M50 RX-M2R 2m Red RX4-M5 5m 3m cable length 5m cable length RX4-M5-C3 RX4-M5-C5 Note: The sensing range of the retroreflective type sensor is specified for the RF-230 reflector. Further, the sensing range of RX-PRVM3, RX-RVM5, RX2-PRVM2 and RX3-PRVM3 is the possible setting range for the reflector. The sensor can detect an object less than 0.1m away. PX-2 Reflector cannot be placed in this range 3m RX-RVM5: 5m Actual sensing range RX2-PRVM2: 2m of the sensor 0.1m Setting range of the reflector RT-610 Sensor Reflector Reflector 5m cable length type 5m cable length models are available (Standard: 2m). When ordering this type, add suffix `-C5' to the model No. (Excluding RX-4) (e.g.) 5m cable length type of RX-M10 is `RX-M10-C5'. 250 OPTIONS Slit mask Slit mask For RX-M10, RX2-M5 and RX3-M10 only ( ) OS-RX-15 (Slit size 15mm) OS-RX-51 (Slit size 51mm) OS-RX-35 (Slit size 35mm) OS-RX-53 (Slit size 53mm) Reflector For retroreflective type sensor only ( ) Reflector mounting bracket Reflective tape (For RX-RVM5 only) Protective tube * Sensing range: 0.4m [RX-M10 and RX3-M10] 0.2m [RX2-M5] * Min. sensing object: 0.55mm Slit on emitter * Sensing range: 3.8m [RX-M10 and RX3-M10] 1.9m [RX2-M5] * Min. sensing object: "8mm Slit on receiver * Sensing range: 2.8m [RX-M10 and RX3-M10] 1.4m [RX2-M5] * Min. sensing object: "6mm Slit on both sides * Sensing range: 0.8m [RX-M10 and RX3-M10] 0.4m [RX2-M5] * Min. sensing object: 15mm Slit on emitter * Sensing range: 7m [RX-M10 and RX3-M10] 3.5m [RX2-M5] * Min. sensing object: "8mm Slit on receiver * Sensing range: 4.9m [RX-M10 and RX3-M10] 2.5m [RX2-M5] * Min. sensing object: "6mm Slit on both sides * Sensing range: 2.6m [RX-M10 and RX3-M10] 1.3m [RX2-M5] * Min. sensing object: 35mm * Sensing range: 0.2 to 1.5m [RX-RVM5] 0.4 to 1m [RX-PRVM3 and RX3-PRVM3] * Min. sensing object: "30mm RF-220 * Sensing range: 0.1 to 3.8m [RX-RVM5] 0.1 to 2m [RX-PRVM3 and RX3-PRVM3] 0.1 to 1.3m [RX2-PRVM2] 250mm [RX-PRV500 and RX3-PRV500] * Min. sensing object: "35mm MS-RF21-1 Protective mounting bracket for RF-210 It protects the reflector from damage and maintains alignment. MS-RF22 For RF-220 MS-RF23 For RF-230 RF-T110 This tape can be used in place of the reflector by cutting it to a suitable size. * Size: 100100mm * Sensing range: 3m (at 5050mm) (There may be a slight variation depending on the product.) PT-RX500 CHX-SC2 Length OS-RX-15 ~~~~ ~~~ a b EQ-20 Slit on both sides RF-210 PT-RX1000 Sensor checker (Note) * Sensing range: 1.9m [RX-M10 and RX3-M10] 1m [RX2-M5] * Min. sensing object: "6mm a Slit mask Reflector * RF-210 * RF-220 33.3mm 11mm 8.3mm 12.8mm EQ-30 OS-RX-505 (Slit size 50.5mm) Slit on receiver b Slit size 35.3mm 42.3mm EX-40 OS-RX-055 (Slit size 0.55mm) * Sensing range: 2.7m [RX-M10 and RX3-M10] 1.4m [RX2-M5] * Min. sensing object: "8mm Reflector mounting bracket * MS-RF21-1 Amplifier Built-in Type RX RX-LS200 Slit on emitter Fitted on the front face of the sensor with one-touch. Two M3 (length 12mm) screws with washers are attached. * MS-RF22 * MS-RF23 CY Description Two M3 (length 8mm) screws with washers are attached. Two M4 (length 10mm) screws with washers are attached. Protective tube EX Model No. 500mm Cable is protected from external forces. It does not rust as it is made of stainless 1,000mm steel. Protective tube It is useful for beam alignment of thru-beam type sensors. The optimum receiver position is given by indicators, as well as, an audio signal. PX-2 Designation PHOTOELECTRIC SENSORS RX RT-610 Note: Refer to P.378l for details of the sensor checker CHX-SC2. Sensor checker PO W ER C LE H VE L X- SC 2 Sensor checker 251 PHOTOELECTRIC SENSORS RX SPECIFICATIONS Standard type EQ-20 Type ( Item Model No. Sensing range Sensing object EQ-30 Thru-beam Retroreflective Diffuse reflective Red (with polarizing filters) Infrared Infrared Infrared Red Green Red Long sensFor transparent Long sensing Wide-view ing range object sensing range RX-M10 RX-M50 RX-M2R RX-500G RX-PRVM3 RX-PRV500 RX-RVM5 RX-D700 RX-D300 RX-D200R 10m 50m 500mm 0.1 to 3m (Note 1) 500mm (Note 1) 0.1 to 5m (Note 1) 700mm (Note 2) 300mm (Note 2) 200mm (Note 2) "50mm or more opaque, translucent or specular object (Note 1) "10mm or more opaque object (Note 3) Repeatability (perpendicular to sensing axis) Current consumption RX-LS200 RX Amplifier Built-in Type CY 0.5mm or less 12 to 24V DC10% Ripple P-P 10% or less 40mA or less NPN open-collector transistor * Maximum sink current: 100mA * Applied voltage: 30V DC or less (between sensing output and 0V) * Residual voltage: 1.5V or less (at 100mA sink current) 0.4V or less (at 16mA sink current) Sensing output DC-12 or DC-13 Switchable either Light-ON or Dark-ON Incorporated Short-circuit protection NPN open-collector transistor * Maximum sink current: 50mA * Applied voltage: 30V DC or less (between self-diagnosis output and 0V) * Residual voltage: 1V or less (at 50mA sink current) 0.4V or less (at 16mA sink current) Self-diagnosis output ON under unstable sensing condition Output operation Short-circuit protection Response time 1ms or less Test input Incorporated Red LED (lights up when the sensing output is ON) Operation indicator Green LED (lights up under stable light received condition or stable dark condition) Stability indicator Emitting indicator Red LED (lights up during beam emission) Continuously variable adjuster Sensitivity adjuster Incorporated (Two units of sensors can be mounted closely.) Automatic interference prevention function 3 (Industrial environment) Environmental resistance Pollution degree EX Opaque, translucent or transparent object 1mm or less 0.2mm or less 1mm or less Emitter: 20mA or less (RX-M50: 25mA or less), Receiver: 25mA or less Output operation PX-2 "50mm or more opaque or translucent object (Note 1) 15% or less of operation distance 0.5mm or less Utilization category IP67 (IEC) Protection 25 to60C (No dew condensation or icing allowed), Storage:30 to70C Ambient temperature 35 to 85% RH, Storage: 35 to 85% RH Ambient humidity Ambient illuminance Sunlight: 11,000?x at the light-receiving face, Incandescent light: 3,500?x at the light-receiving face Emission: EN50081-2, Immunity: EN50082-2 EMC 1,000V AC for one min. between all supply terminals connected together and enclosure Voltage withstandability Insulation resistance 20M, or more, with 250V DC megger between all supply terminals connected together and enclosure Vibration resistance 10 to 500Hz frequency, 1.5mm amplitude (10G max.) in X, Y and Z directions for two hours each 500m/s2 acceleration (50G approx.) in X, Y and Z directions for three times each Shock resistance Emitting element Material Cable RT-610 "50mm or more opaque, translucent or transparent object (Note 1) Hysteresis Supply voltage EX-40 2m ) Cable extension Infrared LED (modulated) Red LED Green LED Red LED (modulated) (modulated) (modulated) Red LED (modulated) Enclosure: Die-cast zinc alloy, Indicator cover: Polyethersulphone, Lens: Polycarbonate (retroreflective type: Acrylic) Emitter: 0.15mm2 3-core oil, heat and cold resistant cabtyre cable, 2m long Receiver: 0.15mm2 4-core oil, heat and cold resistant cabtyre cable, 2m long 0.15mm2 5-core oil, heat and cold resistant cabtyre cable, 2m long Extension up to total 100m is possible with 0.3mm2, or more, cable (thru-beam type: both emitter and receiver). Weight Emitter: 70g approx. (RX-M50: 75g approx.) Receiver: 70g approx. (RX-M50: 75g approx.) Accessories MS-RX-1 (Sensor mounting bracket): 2 sets Adjusting screwdriver: 1 No. 75g approx. MS-RX-1 (Sensor mounting bracket): 1 set RF-230 (Reflector): 1 No. Adjusting screwdriver: 1 No. Notes: 1) The sensing range and the setting object for the retroreflective type sensor are specified for the RF-230 reflector. Further, the sensing range of RX-PRVM3 and RX-RVM5 is the possible setting range for the reflector. The sensor can detect an object less than 0.1m away. Notes: 2) The sensing range of the diffuse reflective type sensor is specified for white nonglossy paper (200200mm) as the object. Notes: 3) If slit masks (optional) are fitted on RX-M10, an object of 0.55mm can be detected. 252 Infrared LED (modulated) Reflector cannot be placed in this range Sensor MS-RX-1 (Sensor mounting bracket): 1 set Adjusting screwdriver: 1 No. Actual sensing range of the sensor 0.1m Setting range of the reflector Reflector 5m (RX-PRVM3: 3m) Reflector DC 2-wire type Type Item Model No. Sensing range Sensing object Thru-beam Retroreflective (with polarizing filters) Diffuse reflective RX2-M5 RX2-PRVM2 RX2-D300 5m 0.1 to 2m (Note 1) 300mm (Note 2) "50mm or more opaque, translucent or "10mm or more opaque object (Note 3) Opaque, translucent or transparent object specular object (Note 1) 15% or less of operation distance Hysteresis 0.5mm or less 1mm or less 12 to 24V DC10% Ripple P-P 10% or less Supply voltage Emitter: 8mA or less, Receiver: 0.8mA or less (Note 4) Sensing output Incorporated Short-circuit protection 3ms or less Response time Red LED (lights up when the output is ON) Green LED Stability indicator ( Light-ON mode: lights up under stable light received condition Dark-ON mode: lights up under stable dark condition Red LED (lights up during beam emission) Sensitivity adjuster Continuously variable adjuster Protection IP67 (IEC) 20 to60C (No dew condensation or icing allowed), Storage:30 to70C Ambient temperature 35 to 85% RH, Storage: 35 to 85% RH Ambient humidity Sunlight: 11,000?x at the light-receiving face, Incandescent light: 3,500?x at the light-receiving face Ambient illuminance Power line: 240Vp, 10ms cycle, and 0.5!s pulse width; Radiation: 300Vp, 10ms cycle, and 0.5!s pulse width (with noise simulator) 1,000V AC for one min. between all supply terminals connected together and enclosure Voltage withstandability Insulation resistance 20M, or more, with 250V DC megger between all supply terminals connected together and enclosure Vibration resistance 10 to 500Hz frequency, 1.5mm amplitude (10G max.) in X, Y and Z directions for two hours each 500m/s2 acceleration (50G approx.) in X, Y and Z directions for three times each Shock resistance Emitting element Infrared LED (modulated) Red LED (modulated) Infrared LED (modulated) Material Enclosure: Die-cast zinc alloy, Indicator cover: Polyethersulphone, Lens: Polycarbonate (RX2-PRVM2: Acrylic) EX 0.15mm2 2-core oil, heat and cold resistant cabtyre cable, 2m long Cable (Note 5) Cable extension Weight Emitter: 70g approx., Receiver: 70g approx. 75g approx. 70g approx. Accessories MS-RX-1 (Sensor mounting bracket): 2 sets Adjusting screwdriver: 1 No. MS-RX-1 (Sensor mounting bracket): 1 set RF-230 (Reflector): 1 No. Adjusting screwdriver: 1 No. MS-RX-1 (Sensor mounting bracket): 1 set Adjusting screwdriver: 1 No. Notes: 1) The sensing range and the sensing object for RX2-PRVM2 are specified for the RF-230 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 0.1m away. Sensor 2m Actual sensing range of the sensor 0.1m Setting range of the reflector Reflector RT-610 Reflector cannot be placed in this range PX-2 Environmental resistance ) Amplifier Built-in Type RX RX-LS200 Operation indicator Noise immunity EX-40 Switchable either Light-ON or Dark-ON Output operation Emitting indicator 1mA or less (Note 4) Non contact DC 2-wire type * Load current: 5 to 100mA * Residual voltage: 4V or less (Note 5) CY Current consumption 0.5mm or less EQ-30 Repeatability (perpendicular to sensing axis) Notes: Notes: Notes: Notes: PHOTOELECTRIC SENSORS SPECIFICATIONS EQ-20 RX Reflector 2) The sensing range of RX2-D300 is specified for white non-glossy paper (200200mm) as the object. 3) If slit masks (optional) are fitted, an object of 0.55mm can be detected. 4) It is the leakage current when the output is in the OFF state. 5) When cable is extended, the residual voltage will be increased. 253 PHOTOELECTRIC SENSORS RX SPECIFICATIONS Intelligent type Type EQ-20 Item Model No. Retroreflective (with polarizing filters) For transparent object sensing RX3-PRVM3 RX3-PRV500 Thru-beam RX3-M10 Sensing range 10m 0.1 to 3m (Note 1) Sensing object "10mm or more opaque object (Note 3) EQ-30 0.5mm or less Current consumption EX-40 Emitter: 20mA or less Receiver: 45mA or less 0.5mm or less 50mA or less NPN open-collector transistor * Maximum sink current: 100mA * Applied voltage: 30V DC or less (between sensing output and 0V) * Residual voltage: 1.5V or less (at 100mA sink current) 0.4V or less (at 16mA sink current) Output operation Switchable either Light-ON or Dark-ON Short-circuit protection Incorporated NPN open-collector transistor * Maximum sink current: 50mA * Applied voltage: 30V DC or less (between self-diagnosis output and 0V) * Residual voltage: 1V or less (at 50mA sink current) 0.4V or less (at 16mA sink current) Output operation ON under unstable sensing or the sensor circuit failure conditions (Note 4) Short-circuit protection Response time 3ms or less Test input Incorporated Operation indicator Red LED (lights up when the sensing output is ON, blinks when the sensor circuit has failed) (Note 4) the sensing output wire is disconnected, lights up under stable light received condition ( orlightsstableup when ) (Note 4) dark condition, and blinks under unstable sensing condition Stability indicator Green LED Emitting indicator Red LED (lights up during beam emission) Sensitivity adjuster Continuously variable adjuster Incorporated (Two units of sensors can be mounted closely.) Automatic interference prevention function Self-diagnosis of incident light intensity and internal circuit failure Self-diagnosis function IP67 (IEC) Protection Environmental resistance RX-LS200 RX Amplifier Built-in Type 0.2mm or less 12 to 24V DC10% Ripple P-P 10% or less Supply voltage Self-diagnosis output CY Opaque, translucent or transparent object "50mm or more opaque, translu- "50mm or more opaque, translucent or specular object (Note 1) cent or transparent object (Note 1) 1mm or less Sensing output EX 700mm (Note 2) 15% or less of operation distance Repeatability (perpendicular to sensing axis) 25 to60C (No dew condensation or icing allowed), Ambient temperature Ambient illuminance Noise immunity Storage:30 to70C 35 to 85% RH, Storage: 35 to 85% RH Ambient humidity Sunlight: 11,000?x at the light-receiving face, Incandescent light: 3,500?x at the light-receiving face Power line: 240Vp, 10ms cycle, and 0.5!s pulse width; Radiation: 300Vp, 10ms cycle, and 0.5!s pulse width (with noise simulator) 1,000V AC for one min. between all supply terminals connected together and enclosure Voltage withstandability Insulation resistance 20M, or more, with 250V DC megger between all supply terminals connected together and enclosure Vibration resistance 10 to 500Hz frequency, 1.5mm amplitude (10G max.) in X, Y and Z directions for two hours each 500m/s2 acceleration (50G approx.) in X, Y and Z directions for three times each Shock resistance Emitting element Infrared LED (modulated) Red LED (modulated) Infrared LED (modulated) Enclosure: Die-cast zinc alloy, Indicator cover: Polyethersulphone, Lens: Polycarbonate (retroreflective type: Acrylic) Material 0.15mm2 5-core (thru-beam type: 4-core) oil, heat and cold resistant cabtyre cable, 2m long Cable PX-2 RX3-D700 500mm (Note 1) Hysteresis RT-610 Diffuse reflective Cable extension Extension up to total 100m is possible with 0.3mm2, or more, cable (thru-beam type: both emitter and receiver). Weight Emitter: 70g approx., Receiver: 70g approx. Accessories MS-RX-1 (Sensor mounting bracket): 2 sets Adjusting screwdriver: 1 No. 75g approx. MS-RX-1 (Sensor mounting bracket): 1 set RF-230 (Reflector): 1 No. Adjusting screwdriver: 1 No. MS-RX-1 (Sensor mounting bracket): 1 set Adjusting screwdriver: 1 No. Notes: 1) The sensing range and the sensing object for the retroreflective type sensor are specified for the RF-230 reflector. Further, the sensing range is the possible setting range for the reflector. The sensor can detect an object less than 0.1m away. Reflector cannot be placed in this range Sensor 3m Actual sensing range of the sensor 0.1m Setting range of the reflector Reflector Reflector Notes: 2) The sensing range of RX3-D700 is specified for white non-glossy paper (200200mm) as the object. Notes: 3) If slit masks (optional) are fitted, an object of 0.55mm can be detected. Notes: 4) Refer to P.261 for details. 254 SPECIFICATIONS Heavy duty type RX4-M5 RX4-M5-C3 RX4-M5-C5 Sensing range 5m Sensing object "10mm or more opaque object Repeatability (perpendicular to sensing axis) EQ-20 Cable length 5m 0.5mm or less Current consumption EQ-30 12 to 24V DC10% Ripple P-P 10% or less Supply voltage Emitter: 20mA or less, Receiver: 25mA or less Sensing output Output operation EX-40 NPN open-collector transistor * Maximum sink current: 100mA * Applied voltage: 30V DC or less (between sensing output and 0V) * Residual voltage: 1.5V or less (at 100mA sink current) 0.4V or less (at 16mA sink current) Switchable either Light-ON or Dark-ON Short-circuit protection Incorporated NPN open-collector transistor * Maximum sink current: 50mA * Applied voltage: 30V DC or less (between self-diagnosis output and 0V) * Residual voltage: 1V or less (at 50mA sink current) 0.4V or less (at 16mA sink current) Self-diagnosis output Output operation Amplifier Built-in Type RX RX-LS200 Model No. Cable length 3m ON under unstable sensing condition Short-circuit protection Response time 1ms or less Test input Incorporated Operation indicator Red LED (lights up when the sensing output is ON) Stability indicator Green LED (lights up under stable light received condition or stable dark condition) Emitting indicator Red LED (lights up during beam emission) Sensitivity adjuster Continuously variable adjuster IP67 (IEC), IP67g (JEM) 25 to60C (No dew condensation or icing allowed), Ambient humidity Ambient illuminance Noise immunity Voltage withstandability Storage:30 to70C 35 to 85% RH, Storage: 35 to 85% RH Sunlight: 11,000?x at the light-receiving face, Incandescent light: 3,500?x at the light-receiving face Power line: 240Vp, 10ms cycle, and 0.5!s pulse width; Radiation: 300Vp, 10ms cycle, and 0.5!s pulse width (with noise simulator) 1,000V AC for one min. between all supply terminals connected together and enclosure Insulation resistance 20M, or more, with 250V DC megger between all supply terminals connected together and enclosure Vibration resistance 10 to 500Hz frequency, 1.5mm amplitude (10G max.) in X, Y and Z directions for two hours each 500m/s2 acceleration (50G approx.) in X, Y and Z directions for three times each Shock resistance Emitting element Material Infrared LED (modulated) Enclosure: Die-cast zinc alloy (Fluorine resin coating), Indicator cover: Polyethersulphone, Lens: Polyalylate, Protective tube sheath: Oil resistant PVC 0.15mm2 4-core (emitter: 3-core) oil, heat and cold resistant cabtyre cable Cable Protective tube length Cable extension Weight Accessories CY Ambient temperature EX Environmental resistance Protection 1m 2m Extension up to total 100m is possible for both emitter and receiver with PX-2 Item Thru-beam Cable length 2m 4m 0.3mm2, or more, cable. Emitter: 175g approx., Receiver: 175g approx. Emitter: 265g approx., Receiver: 265g approx. Emitter: 495g approx., Receiver: 495g approx. MS-RX-2 (Sensor mounting bracket): 2 sets, Adjusting screwdriver: 1 No. 255 RT-610 Type PHOTOELECTRIC SENSORS RX PHOTOELECTRIC SENSORS RX I/O CIRCUIT AND WIRING DIAGRAMS RX- RX3- RX4- I/O circuit diagram Wiring diagram Load m1 ZD1 ZD2 Black (Pink) Test input 1mA max. (Note 1) Load 100mA max. Tr1 (Orange) Self-diagnosis output (Note 3) 12 to 24V DC 10% Blue m1 Pink (Blue) 0V Users' circuit Notes: 1) The receiver of the thru-beam type sensor does not incorporate the test input. Notes: 2) The emitter of the thru-beam type sensor does not incorporate the sensing output. Notes: 3) The emitter of the thru-beam type sensors RX and RX4 does not incorporate the self-diagnosis output. m1 Non-voltage contact or NPN open-collector transistor or [Supply voltage 2.5V] or more (4.5V or more for the RX3 model): emission [Supply voltage 3.3V] or less (2.5V or less for the RX3 model): emission stopped RX2- I/O circuit diagram Wiring diagrams Emitter of thru-beam type sensor Emitter of thru-beam type sensor Color code (Brown) V D Sensor circuit RX-LS200 RX Amplifier Built-in Type 50mA max. Tr2 Orange 12 to 24V DC 10% Symbols ... D: Reverse supply polarity protection diode ZD1, ZD2: Surge absorption zener diode Tr1, Tr2 : NPN output transistor CY Load Load (Black) Sensing output (Note 2) Internal circuit EX-40 Brown (Brown) V D Sensor circuit EQ-30 EQ-20 Color code Brown 12 to 24V DC 10% (Blue) 0V 12 to 24V DC 10% Blue Internal circuit Users' circuit (Brown) Output Tr ZD Load 5 to 100mA in the ON state 4V in the 1mA in the OFF state ON state Receiver of thru-beam type sensor: 0.8mA (Blue) 0V ( ) Brown 12 to 24V DC 10% Users' circuit Symbols ... D: Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : PNP output transistor Conditions for the load 1) The load should not be actuated by the leakage current (1mA; 0.8mA for receiver of thru-beam type sensor) in the OFF state. 2) The load should be actuated by (supply voltage 4V) in the ON state. 3) The current in the ON state should be between 5 to 100mA DC. In case the current is less than 5mA, connect a bleeder resistance in parallel to the load (shown in dotted line above) so that a current of 3mA, or more, flows. 256 Load Blue Internal circuit RT-610 Receiver of thru-beam type sensor, retroreflective and diffuse reflective type sensors Color code Bleeder resistance Sensor circuit PX-2 EX Receiver of thru-beam type sensor, retroreflective and diffuse reflective type sensors 12 to 24V DC 10% SENSING CHARACTERISTICS (TYPICAL) RX- All models PHOTOELECTRIC SENSORS RX 100 100 50 50 50 5 10 RX-PRVM3 5 RX-D700 RX-PRV500 10 RX-500G 5 RX-D300 RX-M2R RX-D200R RX-M10 0 20 40 60 80 Setting distance L (m) RX-M103 RX3-M10 1 100 0 2 4 6 8 Setting distance L (m) 1 10 0 200 400 600 800 Setting distance L (mm) 1,000 EX-40 1 EQ-30 10 Excess gain RX-RVM5 RX-M50 Excess gain Excess gain 100 EQ-20 Correlation between setting distance and excess gain Thru-beam type Parallel deviation Angular deviation Emitter 5 # 0 400 L Receiver L Receiver angular deviation Receiver Emitter angular deviation 5 0 10 200 0 200 400 Left Center Right Operating point ? (mm) Parallel deviation with slit masks (0.55mm) $ 10 5 0 5 10 Left Center Right Operating angle $( ) Parallel deviation with slit masks (15mm) 4 Amplifier Built-in Type RX RX-LS200 10 Setting distance L (m) Setting distance L (m) Emitter Parallel deviation with slit masks (35mm) 4 8 L Slit on both sides 1 0 200 CY 2 # 0 400 L Receiver 200 0 200 400 Left Center Right Operating point ? (mm) RX-M2R Thru-beam type Parallel deviation Angular deviation 60 40 Emitter # L Receiver 500 0 500 1,000 Left Center Right Operating point ? (mm) 60 Receiver angular deviation Emitter angular deviation 40 Emitter $ 20 0 10 L Receiver 5 0 5 10 Left Center Right Operating angle $( ) 2 1 Emitter # 0 200 L Receiver 100 0 100 200 Left Center Right Operating point ? (mm) RT-610 80 Setting distance L (m) Setting distance L (m) Emitter Slit on both side Slit on emitter 100 0 100 200 Left Center Right Operating point ? (mm) Angular deviation 80 0 1,000 Slit on receiver Thru-beam type Parallel deviation 20 4 Receiver Receiver 100 0 100 200 Left Center Right Operating point ? (mm) RX-M50 L # Slit on both sides 0 200 Emitter EX # 2 PX-2 Slit on receiver Emitter 6 Setting distance L (m) 1 Slit on emitter Slit on receiver Setting distance L (m) 2 3 Setting distance L (m) 3 Setting distance L (m) Setting distance L (m) Slit on emitter 2 1 Emitter $ L 0 40 Receiver 20 0 20 40 Left Center Right $ Operating angle ( ) 257 SENSING CHARACTERISTICS (TYPICAL) RX-500G Parallel deviation Angular deviation Thru-beam type Parallel deviation Angular deviation 8 800 8 Emitter 400 Emitter # 200 L $ 600 L Receiver 400 200 $ 6 4 Emitter 2 # 0 10 20 0 20 40 Left Center Right Operating point ? (mm) RX2-M5 6 0 400 5 0 5 10 Left Center Right Operating angle $( ) Receiver 2 0 10 200 0 200 400 Left Center Right Operating point ?(mm) L 4 Receiver Receiver 0 40 L Setting distance L (m) 600 Setting distance L (mm) Emitter Setting distance L (mm) EQ-30 EQ-20 800 EX-40 RX4-M5 Thru-beam type Setting distance L (m) PHOTOELECTRIC SENSORS RX Receiver angular deviation Emitter angular deviation 5 0 5 10 Left Center Right Operating angle $( ) Thru-beam type Parallel deviation Angular deviation 8 8 Emitter # L Receiver Receiver 4 Receiver angular deviation Emitter angular deviation 2 0 10 200 0 200 400 Left Center Right Operating point ? (mm) 5 0 5 10 Left Center Right $ Operating angle ( ) Parallel deviation with slit masks (15mm) 2 Parallel deviation with slit masks (35mm) 2 4 Slit on emitter Slit on emitter 1 Emitter Slit on receiver Slit on both sides PX-2 # L 1 Emitter 0.5 Slit on both sides Reflector (RF-230) 258 # L Sensor 50 0 50 100 Left Center Right Operating point ? (mm) Setting distance L (m) Setting distance L (m) $ Reflector (RF-230) Emitter Slit on receiver 1 Slit on both sides 2 Receiver Retroreflective type Angular deviation 800 800 Reflector (RF-230) Reflector angular deviation Reflector (RF-230) $ L $ Reflector angular deviation L Sensor Sensor angular deviation 1 0 40 L Parallel deviation 3 Sensor # 100 0 100 200 Left Center Right Operating point ? (mm) RX-PRV5003 RX3-PRV500 4 Sensor angular deviation Reflector angular deviation 2 2 0 200 50 0 50 100 Left Center Right Operating point ? (mm) Angular deviation 3 3 Receiver 0 100 4 0 100 L Retroreflective type Parallel deviation 1 # Receiver 50 0 50 100 Left Center Right Operating point ? (mm) RX-PRVM33 RX3-PRVM3 Slit on receiver 20 0 20 40 Left Center Right Operating angle $( ) Setting distance L (mm) 0.5 1.5 Setting distance L (m) 1.5 Setting distance L (m) Slit on emitter 0 100 RT-610 L 6 600 400 Reflector (RF-230) 200 0 100 # L Sensor 50 0 50 100 Left Center Right # Operating point (mm) Setting distance L (mm) 2 Setting distance L (m) Setting distance L (m) Emitter Parallel deviation with slit masks (0.55mm) Setting distance L (m) EX 4 0 400 CY RX-LS200 RX Amplifier Built-in Type $ 6 L 600 400 200 0 40 Sensor angular deviation Reflector (RF-230) $ Reflector Sensor angular deviation Sensor angular deviation L Sensor 20 0 20 40 Left Center Right Operating angle $( ) SENSING CHARACTERISTICS (TYPICAL) Parallel deviation Setting distance L (m) 4 Reflector (RF-230) # Sensor RX-D7003 RX3-D700 200200mm White nonglossy paper # L 600 Sensor 400 200 20 0 20 40 Left Center Right Operating angle $( ) # 0 100 L Sensor 50 0 50 100 Left Center Right Operating point # (mm) L Sensor 1 Sensor angular deviation Reflector (RF-230) Reflector angular deviation $ Sensor angular deviation 0 40 L Sensor 20 0 20 40 Left Center Right Operating angle $( ) aamm White nonglossy paper 200 L ( For plotting the left graph, the sensitivity has been set such that a 200200mm white non-glossy paper is just detectable at a distance of 700mm. ) 200 200200mm White non-glossy paper L aamm White nonglossy paper 100 L Sensor CY ) Sensor 0 10 0 10 20 Left Center Right Operating point # (mm) RX-D200R ( For plotting the left graph, the sensitivity has been set such that a 200200mm white non-glossy paper is just detectable at a distance of 300mm. 50 100 150 White non-glossy paper side length a (mm) 200 PX-2 # 200 EX 200 100 50 100 150 White non-glossy paper side length a (mm) Correlation between sensing object size and sensing range 400 As the sensing object size becomes smaller than the standard size (white non-glossy paper 200200mm), the sensing range shortens, as 300 shown in the left graph. 300 Diffuse reflective type Sensing field Correlation between sensing object size and sensing range 200 As the sensing object size becomes smaller than the standard size (white non-glossy paper 200200mm), the sensing range shortens, as shown in the left graph. 200 200200mm White nonglossy paper # L 100 10 0 10 20 Left Center Right Operating point # (mm) aamm White nonglossy paper L ( For plotting the left graph, the sensitivity has been set such that a 200200mm white non-glossy paper is just detectable at a distance of 200mm. ) Sensor Sensor 20 L Sensor 400 0 Sensing range L (mm) Setting distance L (mm) $ 1 $ Diffuse reflective type 400 Setting distance L (mm) 2 Reflector (RF-230) 2 Sensor Sensing field 0 Sensor angular deviation 2 Correlation between sensing object size and sensing range 800 As the sensing object size becomes smaller than the standard size (white non-glossy paper 200200mm), the sensing range shortens, as 600 shown in the left graph. 10 0 10 20 Left Center Right # Operating point (mm) RX-D300 100 Sensor angular deviation Reflector (RF-230) Sensor RT-610 Setting distance L (mm) 800 0 20 Reflector angular deviation Diffuse reflective type Sensing field 0 20 4 0 40 50 0 50 100 Left Center Right Operating point # (mm) Sensing range L (mm) 0 100 L 6 Reflector angular deviation Reflector (RF-230) L Amplifier Built-in Type RX RX-LS200 2 Sensing range L (mm) Setting distance L (m) $ 6 Angular deviation Reflector angular deviation Reflector (RF-230) EQ-20 8 EX-40 Angular deviation 8 Setting distance L (m) Parallel deviation Retroreflective type EQ-30 RX2-PRVM2 Retroreflective type Setting distance L (m) RX-RVM5 PHOTOELECTRIC SENSORS RX 0 50 100 150 White non-glossy paper side length a (mm) 200 259 SENSING CHARACTERISTICS (TYPICAL) RX2-D300 Diffuse reflective type Sensing field Correlation between sensing object size and sensing range 400 As the seinsing object size becomes smaller than the standard size (white non-glossy paper 200200mm), the sensing range shortens, as 300 shown in the left graph. EX-40 Setting distance L (mm) EQ-30 EQ-20 400 300 200 200200mm White nonglossy paper 100 # 0 20 L Sensing range L (mm) PHOTOELECTRIC SENSORS RX 200 aamm White nonglossy paper 100 L Sensor 10 0 10 20 Left Center Right Operating point # (mm) ) Sensor 0 50 100 150 White non-glossy paper side length a (mm) 200 PRECAUTIONS FOR PROPER USE All models Refer to P.820l for general precautions. RX-RVM5 This product is not a safety sensor. Its use is not intended or designed to protect life and prevent body injury or property damage from dangerous parts of machinery. It is a normal object detection sensor. Mounting * The tightening torque should be 1.17N m or less. Glossy object sensing * Please take care of the following points when detecting materials having a gloss. 1 Make L, shown in the diagram, sufficiently long. 2 Install at an angle of 10 to 30 degrees to the sensing object. Reflector Glossy surface Sensing object M4 (length 16mm) hexagon-socket-head bolt 10 to 30 CY RX-LS200 RX Amplifier Built-in Type ( For plotting the left graph, the sensitivity has been set such that a 200200mm white non-glossy paper is just detectable at a distance of 300mm. Attached mounting bracket Sensor Wiring * The self-diagnosis output is not incorporated with a shortcircuit protection circuit. Do not connect it directly to a power supply or a capacitive load. Others * Do not use during the initial transient time (50ms) after the power supply is switched on. RT-610 PX-2 EX L Make L sufficiently long RX-PRVM3 RX-PRV500 RX2-PRVM2 Retroreflective type sensor with polarizing filters * If a shiny object is covered or wrapped with a transparent film such as those described below, the retroreflective type sensor with polarizing filters may not be able to detect it. In that case, follow the steps given below. Example of sensing objects * Can wrapped by clear film * Aluminum sheet covered by plastic film * Gold or silver color (glossy) label or wrapping paper Steps * Tilt the sensor with respect to the sensing object while fitting. * Reduce the sensitivity. * Increase the distance between the sensor and the sensing object. 260 Wiring * Always connect the sensor to the power supply through a load. If the sensor is connected to the power supply directly, the short-circuit protection makes the sensor inoperable (The output stays in the OFF state and no indicator lights up). If this happens, connect the sensor to the power supply through a load. Further, note that the sensor will be damaged if the power supply is connected in reverse without a load. Self-diagnosis output * The self-diagnosis output turns ON when the incident light intensity is reduced due to the lens being soiled with dust or dirt, due to beam misalignment, or if the internal circuit has failed. If the self-diagnosis output and the operation indicator behave as given in the table below, abnormality is indicated and should be rectified. Symptoms Selfdiagnosis output Brown lead wire Failure Remedy Sensing output wire is disconnected during unstable light received condition or unstable dark condition. Check the sensing output wire (black lead wire) and the placement of the sensor. Failure of the sensor circuit. Failure of the emitting or receiving elements, emitting circuit, amplifier circuit, or output transistor. If the sensor does not operate after the power is supplied once again, please contact our office. Lights up Sensing output wire is disconnected. Check the sensing output wire (black lead wire). Blinking Lights up/ pattern 2 Lights off (Note 1) Blinking Lights up/ pattern 2 Lights off (Note 1) Sensing output is shortcircuited and excessive current flows. Check the sensing output wire (black lead wire) and the load. Unstable sensing condition due to soiled lens or beam misalignment. (Note 2) Check the placement of the sensors and the surface condition of the lenses. Brown lead wire DC power supply Blue lead wire DC power supply Blinking pattern 1 (Note 1) Blue lead wire Lights off ( ON * Do not connect sensors in series (AND circuit). ) Notes: 1) There are two blinking patterns of the operation indicator and the stability indicator. Load ON Blinking pattern 1 Repeat OFF 0.1 sec. 0.4 sec. 0.1 sec. ON DC power supply Blinking pattern 2 OFF Repeat 0.1 sec. 0.1 sec. 0.1 sec. 0.3 sec. CY Operation Stability indicator indicator (Red LED) (Green LED) PHOTOELECTRIC SENSORS RX3- EQ-20 RX2- EQ-30 Refer to P.820l for general precautions. EX-40 PRECAUTIONS FOR PROPER USE Amplifier Built-in Type RX RX-LS200 RX 0.1 sec. 0.1 sec. 0.1 sec. 2) The time chart for unstable light received condition and unstable dark condition are shown in the following diagram. Stable light received level Sensing output threshold level Sensing condition Stable dark level Sensing output operation indicator in the LightON mode ( ( ) ON (Lights up) ) OFF (Lights off) Relay VR (Relay actuation voltage) VS4V Residual voltage when the sensing output is ON. ( 12V DC ) Relay actuation voltage: VRh124V h8V (Blink 2) Self-diagnosis output 1 2 1 PX-2 Lights up Stability indicator Lights off (Blink 2) ON 3 OFF 1 The self-diagnosis output transistor stays in the `OFF' state during stable sensing. 2 When the sensing output changes, if the incident light intensity does not reach the stable light received level or the stable dark level, the selfdiagnosis output becomes ON. Further, the self-diagnosis output changes state when the sensing output changes from Light to Dark state. (It is not affected by the operation mode switch.) 3 In case of insufficient beam interruption, there will be a time lag before the self-diagnosis output turns ON. 3) For the emitter of the thru-beam type diagnosis is only for the emitting element and circuit failure, and the failure is indicated by blinking pattern 1. 4) The self-diagnosis output (for sensing output wire disconnection, output transistor failure) may not be generated or changed depending on the fault conditions. 5) When the test input is connected to 0V, the self-diagnosis is inoperable. 6) Turning the sensitivity adjuster to the minimum simulates the internal circuit failure condition. Set it at the proper position. 261 RT-610 * The residual voltage of the sensor is 4V. Before connecting to a relay, be aware of the actuation voltage of the relay. (Not all 12V relays may be connected as the load.) Insufficient beam interruption EX Insufficient beam intensity PHOTOELECTRIC SENSORS EQ-20 RX PRECAUTIONS FOR PROPER USE Refer to P.820l for general precautions. RX-4 RX4- RX4- Connection of protective tube connector * Connect the junction connector securely as shown below. The tightening torque should be 0.98N m or less. When mounted on a plate Self-diagnosis function * The sensor diagnoses the incident light intensity, and if it is reduced due to dirt or dust, or beam misalignment an output is generated. Insufficient beam intensity 7mm or less Insufficient beam interruption "14.5 hole Oil resistant cable Sensing condition M14 nut (Accessory) Sensing output (operation indicator) (in the Light-ON mode) EQ-30 Oil resistant protective tube Junction connector Stable light received level Sensing output threshold level Stable dark level ON (Lights up) OFF (Lights off) Lights up EX-40 Stability indicator Self-diagnosis output When mounted with a female screw Effective thread length 11mm or more M141 tapped hole Junction connector 2 1 1 3 ON OFF 1 The self-diagnosis output transistor stays in the `OFF' state during stable sensing. 2 When the sensing output changes, if the incident light intensity does not reach the stable light received level or the stable dark level, the selfdiagnosis output becomes ON. Further, the self-diagnosis output changes state when the sensing output changes from Light to Dark state. (It is not affected by the operation mode switch.) 3 In case of insufficient beam interruption, there will be a time lag before the self-diagnosis output turns ON. When connected to another protective tube Oil resistant protective tube Can be connected to a straight combination connector (RCC-F1060-M14) manufactured by NIPPON FLEX Junction connector CY RX-LS200 RX Amplifier Built-in Type Oil resistant protective tube Lights off EX DIMENSIONS (Unit: mm) RX-M10 RX-M2R RX-500G RX2-M5 RX3-M10 RX-M50 Sensor Sensitivity adjuster (Note 1) Operation mode switch (Note 1) Sensor Sensitivity adjuster (Note 1) Operation mode switch (Note 1) Stability indicator (Green) (Note 2) Stability indicator (Green) (Note 2) Cover-fixing screw PX-2 Cover-fixing screw Operation indicator (Red) (Note 1) Indicator cover 14 14 35 (2.5) 3 RT-610 (2.5) 3 2-M40.7 thru-hole threads Beam axis 35 14 35 20 3.6 14 "3.7 cable 2m long M80.75 Notes: 1) Not incorporated on the emitter. Notes: 2) It is the emitting indicator (red) on the emitter of the thru-beam type sensor. 262 43 2-M40.7 thru-hole threads Beam axis 20 Operation indicator (Red) (Note 1) Indicator cover 14 3.6 14 "3.7 cable 2m long M80.75 Notes: 1) Not incorporated on the emitter. Notes: 2) It is the emitting indicator (red) on the emitter of the thru-beam type sensor. DIMENSIONS (Unit: mm) Stability indicator (Green) EQ-20 Cover-fixing screw Cover-fixing screw Stability indicator (Red) (Note 1) Operation indicator (Red) Indicator cover 2-M40.7 thru-hole threads 14 "9 oil resistant protective tube 2m long (Note 3) 14 (Oil resistant PVC) " 3.7 cable " 14 15 10 39 (2.5) 14 35 20 (16.5) 3 2-M40.7 thru-hole threads Center of sensing 14 35 Connector on the sensor (Brass * Black chromate) 20.9 Junction connector (Brass) Waterproof packing 15.5 3.6 14 M141 (NBR) "3.7 cable 2m long M80.75 Notes: 1) Not incorporated on the emitter. Notes: 2) It is the emitting indicator (red) on the emitter of the thru-beam type sensor. Notes: 3) The given length of the protective tube is for RX4-M5-C3. Notes: 3) (RX4-M5: 1m, RX4-M5-C5: 4m) RX-D700 RX-D300 RX-D200R RX2-D300 RX3-D700 RF-230 Sensor Sensitivity adjuster Operation mode switch Reflector (Accesory for the retroreflective type sensor) Stability indicator (Green) Cover-fixing screw 14 49.3 35 (2.5) 50.3 Operation indicator (Red) Indicator cover 59.3 3 2-M40.7 thru-hole threads Center of sensing 15.5 (30) 10 14 35 5 3.6 14 2-"4.6 mounting holes 40 "3.7 cable 2m long 3.3 8.3 Material: Acrylic (Reflector) Material: ABS (Base) EX M80.75 EQ-30 35 3 EX-40 Beam axis Sensitivity adjuster Operation mode indicator Stability indicator (Green) (Note 2) Indicator cover (2.5) Sensor Amplifier Built-in Type RX RX-LS200 Sensitivity adjuster (Note 1) Operation mode switch (Note 1) 14 RX-PRVM3 RX-PRV500 RX-RVM5 RX2-PRVM2 RX3-PRVM3 RX3-PRV500 Sensor CY RX4-M5 PHOTOELECTRIC SENSORS RX RF-210 Reflector (Optional) Reflector (Optional) PX-2 RF-220 33.3 35.3 12.8 42.3 34.3 M3 nut mounting holes (for mounting at the back) Reflector 11 8 25 Material: Acrylic (Reflector) Material: ABS (Base) Base 4 2-"3.6 mounting holes 3.3 RT-610 (21) 2-"3.4 thru-holes (for mounting at the side) 3.2 25 8.3 10 Material: Acrylic (Reflector) Material: ABS (Base) Two M3 (length 8mm) screws with washers and two nuts are attached. 2-"3.4 holes 6 deep (for mounting at the back) 2-M3 nut mounting holes (for mounting at the side) 263 PHOTOELECTRIC SENSORS RX DIMENSIONS (Unit: mm) MS-RX-1 Sensor mounting bracket (Accessory for RX-, RX2-, RX3-) EQ-20 Assembly dimensions Mounting drawing with RX-D700 4.4 8 16 10 4.4 17 8 4.4 8.5 10 Material: Cold rolled carbon steel (SPCC) Two M4 (length 16mm) hexagon-socket-head bolts are attached. 37 EQ-30 13.5 10 8.5 37 14 13.5 5 6 4.4 (2.5) 35 15 2 4.4 5 R14 3 45 45 EX-40 38 24 25.5 15 t2 16 23 30 RX-LS200 RX Amplifier Built-in Type MS-RX-2 Sensor mounting bracket (Accessory for RX4-) 4.4 8 16 10 Material: Cold rolled carbon steel (SPCC) Two M4 (length 16mm) hexagon-socket-head bolts are attached. 10 4.4 Assembly dimensions Mounting drawing with RX4-M5 8.5 10 8 37 13.5 5 8.5 10 37 14 15 (2.5) 35 4.4 2 5 3 4.4 4.4 13.5 16 Beam axis R14 CY 35 57 57 50 42 15 36 t2 t2 EX 17 30 MS-RF21-1 Reflector mounting bracket for RF-210 (Optional) Assembly dimensions 23 PX-2 23 5.5 5.5 "36 50 "36 50 30 RT-610 Material: Stainless steel (SUS304) Two M3 (length 12mm) screws with washers are attached. 30 20 16 10 20 10 3.5 3.2 R7.5 "25 t 1.2 12.5 13 264 46 25 46 25 12.8 13 DIMENSIONS (Unit: mm) MS-RF22 Reflector mounting bracket for RF-220 (Optional) PHOTOELECTRIC SENSORS RX Assembly dimensions 25 EQ-20 25 4.5 10 4.5 10 11 28.3 19.3 8.3 35 35.3 4 EQ-30 25 16 44 10 34.3 44.3 t 1.6 (27) t 1.6 8 6 8-M30.5 thru-hole threads 20 Material: Cold rolled carbon steel (SPCC) Material: (Uni-chrome plated) Two M3 (Length 8mm) screws with washers are attached. MS-RF23 (21) EX-40 8 6 4 Amplifier Built-in Type RX RX-LS200 Reflector mounting bracket for RF-230 (Optional) Assembly dimensions 40 4.5 10 40 4.5 (3) 11 50 40 10 28.3 19.3 8.3 5 50.3 16 15 35 61 t2 12 7 (3) 26 (28) CY 49.3 61.3 18 (30) (37) 5 7 20 8-M40.7 thru-hole threads 10 t2 40 "18 L 15 6.5 "10 (Brass) PX-2 Protective tube (Optional) "7 spiral tube [Stainless steel (SUS304)] "5 14 M101 thread [Brass (C3604) (Nickel plated)] RT-610 PT-RX5000 PT-RX1000 EX Material: Cold rolled carbon steel (SPCC) Material: (Uni-chrome plated) Two M4 (Length 10mm) screws with washers are attached. Internal thread M80.75, 4 deep Length L Model No. L (mm) PT-RX500 1,500100 PT-RX1000 1,000100 265