L6386AD High-voltage high and low side driver Features High voltage rail up to 600 V dV/dt immunity 50 V/nsec in full temperature range Driver current capability: - 400 mA source, - 650 mA sink Description Switching times 50/30 nsec rise/fall with 1nF load CMOS/TTL Schmitt trigger inputs with hysteresis and pull down Under voltage lock out on lower and upper driving section Integrated bootstrap diode Outputs in phase with inputs Figure 1. SO-14 The L6386AD is an high-voltage device, manufactured with the BCD "OFF-LINE" technology. It has a driver structure that enables to drive independent referenced Channel Power MOS or IGBT. The high-side (floating) section is enabled to work with voltage rail up to 600 V. The Logic Inputs are CMOS/TTL compatible for ease of interfacing with controlling devices. Block diagram BOOTSTRAP DRIVER Vboot 14 VCC 4 UV DETECTION UV DETECTION H.V. HVG DRIVER R R HIN SD 3 2 LEVEL SHIFTER HVG 13 S OUT VCC LOGIC 12 TO LOAD LVG LVG DRIVER LIN CBOOT 1 9 PGND 8 VREF - 5 DIAG + SGND 7 6 CIN D97IN520D July 2008 Rev 1 1/17 www.st.com 17 Contents L6386AD Contents 1 Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.3 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 3.1 AC operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.2 DC operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.3 Timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Bootstrap driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4.1 CBOOT selection and charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 5 Typical characteristic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2/17 L6386AD Electrical data 1 Electrical data 1.1 Absolute maximum ratings Table 1. Absolute maximum ratings Symbol Parameter Value Unit Vout Output voltage -3 to Vboot - 18 V Vcc Supply voltage - 0.3 to +18 V -1 to 618 V Vboot Floating supply voltage Vhvg High-side gate output voltage - 1 to Vboot V Vlvg Low-side gate output voltage -0.3 to Vcc +0.3 V Logic input voltage -0.3 to Vcc +0.3 V Vdiag Open drain forced voltage -0.3 to Vcc +0.3 V Vcin Comparator input voltage -0.3 to 10 V V dVout/dt Allowed output slew rate 50 V/ns Total power dissipation (TJ = 85 C) 750 mW Tj Junction temperature 150 C Tstg Storage temperature -50 to 150 C Vi Ptot Note: ESD immunity for pins 12, 13 and 14 is guaranteed up to 900V (Human Body Model) 1.2 Thermal data Table 2. Thermal data Symbol Rth(JA) 1.3 Parameter Thermal Resistance Junction to ambient SO-14 Unit 165 C/W Recommended operating conditions Table 3. Symbol Recommended operating conditions Pin Parameter Test condition Min Vout 12 Output voltage (1) VBS (2) 14 Floating supply voltage (1) Switching frequency fsw Vcc TJ 4 HVG,LVG load CL = 1 nF Supply voltage Junction temperature -45 Typ Max Unit 580 V 17 V 400 kHz 17 V 125 C 1. If the condition Vboot - Vout < 18 V is guaranteed, Vout can range from -3 to 580 V 2. VBS = Vboot - Vout 3/17 Pin connection 2 L6386AD Pin connection Figure 2. Pin connection (Top view) LIN 1 14 Vboot SD 2 13 HVG HIN 3 12 OUT VCC 4 11 N.C. DIAG 5 10 N.C. CIN 6 9 LVG SGND 7 8 PGND D97IN521A Table 4. Pin description N Pin Type 1 LIN I Low-side driver logic input 2 SD(1) I Shut down logic input 3 HIN I High-side driver logic input 4 VCC 5 DIAG O Open drain diagnostic output 6 CIN I Comparator input 7 SGND Ground 8 PGND Power ground 9 LVG (1) 10, 11 N.C. 12 OUT 13 14 HVG (1) Vboot Function Low voltage supply O Low-side driver output Not connected O High-side driver floating driver O High-side driver output Bootstrapped supply voltage 1. The circuit guarantees 0.3V maximum on the pin (@ Isink = 10 mA), with VCC >3V. This allows to omit the "bleeder" resistor connected between the gate and the source of the external MOSFET normally used to hold the pin low; the gate driver assures low impedance also in SD condition. 4/17 L6386AD Electrical characteristics 3 Electrical characteristics 3.1 AC operation Table 5. Symbol ton toff tsd tr AC operation electrical characteristcs (VCC = 15 V; TJ = 25 C) Pin High/low-side driver turn-on 1,3 vs propagation delay 9,13 High/low-side driver turn-off propagation delay 2 vs 9,13 Test condition Min Vout = 0 V Shut down to high/low side propagation delay Typ Max Unit 110 150 ns 110 150 ns 105 150 Rise time CL = 1000 pF 50 ns Fall time CL = 1000 pF 30 ns 9, 13 tf 3.2 Parameter DC operation Table 6. Symbol DC operation electrical characteristcs (VCC = 15 V; TJ = 25 C) Pin Parameter Test condition Min Typ Max Unit Low supply voltage section Vccth1 Vcc UV turn on threshold 9.1 9.6 10.1 V Vccth2 Vcc UV turn off threshold 7.9 8.3 8.8 V Vcchys 4 Vcc UV hysteresis 1.3 V A Iqccu Undervoltage quiescent supply current Vcc 9 V 200 Iqcc Quiescent current Vcc = 15 V 250 320 A Bootstrapped supply section Vbth1 Vboot UV turn on threshold 8.5 9.5 10.5 V Vbth2 Vboot UV turn off threshold 7.2 8.2 9.2 V Vbhys Iqboot Ilk RDS(on) 14 Vboot UV hysteresis 1.3 V Vboot quiescent current HVG ON 200 A High voltage leakage current Vhvg = Vout = Vboot = 600 V 10 A Bootstrap driver on resistance (1) Vcc 12.5 V; Vin = 0 V 125 5/17 Electrical characteristics Table 6. Symbol L6386AD DC operation electrical characteristcs (continued)(VCC = 15 V; TJ = 25 C) Pin Parameter Test condition Min Typ Max Unit Driving buffers section Iso 9, 13 High/low side source short circuit current VIN = Vih (tp < 10 s) 300 400 mA Isi 9, 13 High/low side sink short circuit current VIN = Vil (tp < 10 s) 500 650 mA Logic inputs Vil Vih Iih Low level logic voltage 1.5 1,2, High level logic voltage 3 High level logic input current V = 15 V IN Iil Low level logic input current 3.6 V V 50 VIN = 0 V 70 A 1 A 10 mV Sense comparator Vio Input offset voltage -10 Iio 6 Input bias current Vcin 0.5 Vol 2 Open drain low level output voltage Iod = -2.5 mA Vref Comparator reference voltage 0.46 1. RDS(on) is tested in the following way: ( V CC - V CBOOT1 ) - ( V CC - V CBOOT2 ) R DSON = -----------------------------------------------------------------------------------------------------I 1 ( V CC ,V CBOOT1 ) - I 2 ( V CC ,V CBOOT2 ) where I1 is pin 14 current when VCBOOT = VCBOOT1, I2 when VCBOOT = VCBOOT2 6/17 A 0.2 0.50 0.8 V 0.54 V L6386AD 3.3 Electrical characteristics Timing diagram Figure 3. Input/output timing diagram HIN LIN SD HOUT LOUT VREF VCIN DIAG D97IN522A Note: SD active condition is latched until next negative IN edge. 7/17 Bootstrap driver 4 L6386AD Bootstrap driver A bootstrap circuitry is needed to supply the high voltage section. This function is normally accomplished by a high voltage fast recovery diode (Figure 4 a). In the L6386AD a patented integrated structure replaces the external diode. It is realized by a high voltage DMOS, driven synchronously with the low side driver (LVG), with in series a diode, as shown in Figure 4 b. An internal charge pump (Figure 4 b) provides the DMOS driving voltage. The diode connected in series to the DMOS has been added to avoid undesirable turn on of it. 4.1 CBOOT selection and charging To choose the proper CBOOT value the external MOS can be seen as an equivalent capacitor. This capacitor CEXT is related to the MOS total gate charge: Q gate C EXT = -------------V gate The ratio between the capacitors CEXT and CBOOT is proportional to the cyclical voltage loss. It has to be: CBOOT>>>CEXT e.g.: if Qgate is 30 nC and Vgate is 10 V, CEXT is 3 nF. With CBOOT = 100 nF the drop would be 300 mV. If HVG has to be supplied for a long time, the CBOOT selection has to take into account also the leakage losses. e.g.: HVG steady state consumption is lower than 200 A, so if HVG TON is 5ms, CBOOT has to supply 1 C to CEXT. This charge on a 1 F capacitor means a voltage drop of 1 V. The internal bootstrap driver gives great advantages: the external fast recovery diode can be avoided (it usually has great leakage current). This structure can work only if VOUT is close to GND (or lower) and in the meanwhile the LVG is on. The charging time (Tcharge ) of the CBOOT is the time in which both conditions are fulfilled and it has to be long enough to charge the capacitor. The bootstrap driver introduces a voltage drop due to the DMOS RDS(on) (typical value: 125 ). At low frequency this drop can be neglected. Anyway increasing the frequency it must be taken in to account. The following equation is useful to compute the drop on the bootstrap DMOS: Q gate V drop = I ch arg e R dson V drop = ------------------- R dson T ch arg e where Qgate is the gate charge of the external power MOS, Rdson is the on resistance of the bootstrap DMOS, and Tcharge is the charging time of the bootstrap capacitor. 8/17 L6386AD Bootstrap driver For example: using a power MOS with a total gate charge of 30 nC the drop on the bootstrap DMOS is about 1 V, if the Tcharge is 5 s. In fact: 30nC V drop = --------------- 125 0.8V 5s Vdrop has to be taken into account when the voltage drop on CBOOT is calculated: if this drop is too high, or the circuit topology doesn't allow a sufficient charging time, an external diode can be used. Figure 4. Bootstrap driver DBOOT VS VBOOT VBOOT VS H.V. H.V. HVG HVG CBOOT VOUT TO LOAD TO LOAD LVG a CBOOT VOUT LVG b D99IN1056 9/17 Typical characteristic 5 L6386AD Typical characteristic Figure 5. Typical rise and fall times vs load capacitance time (nsec) D99IN1054 250 Figure 6. Quiescent current vs supply voltage Iq (A) 104 D99IN1057 200 Tr 103 150 Tf 100 102 50 10 0 0 1 2 3 4 5 C (nF) For both high and low side buffers @25C Tamb Figure 7. Turn on time vs temperature Figure 8. 4 6 8 10 12 14 16 VS(V) VBOOT UV turn on threshold vs temperature 15 250 @ Vcc = 15V 14 @ Vcc = 15V 200 13 Vbth1 (V) Ton (ns) 2 0 150 Typ. 100 12 Typ. 11 10 9 50 8 0 -45 Figure 9. -25 0 25 50 Tj (C) 75 100 7 125 -45 0 25 50 Tj (C) 75 100 125 Turn Off time vs temperature Figure 10. VBOOT UV turn off threshold vs temperature 15 250 @ Vcc = 15V 14 @ Vcc = 15V Vbth2 (V) 200 Toff (ns) -25 150 Typ. 100 13 12 11 10 Typ. 9 50 8 0 7 -45 10/17 -25 0 25 50 Tj (C) 75 100 125 -45 -25 0 25 50 Tj (C) 75 100 125 L6386AD Typical characteristic Figure 11. Shutdown time vs temperature Figure 12. VBOOT UV hysteresis 3 250 @ Vcc = 15V @ Vcc = 15V 2.5 Vbhys (V) tsd (ns0 200 150 Typ. 100 Typ. 2 1.5 50 0 -45 -25 0 25 50 Tj (C) 75 100 1 125 Figure 13. VCC UV turn on threshold vs temperature -45 -25 0 25 50 Tj (C) 75 100 125 Figure 14. Output source current vs temperature 15 1000 14 800 current (mA) Vccth1(V) @ Vcc = 15V 13 12 Typ. 600 Typ. 400 11 200 10 9 0 -45 -25 0 25 50 Tj (C) 75 100 125 Figure 15. VCC UV turn off threshold vs temperature -45 -25 0 25 50 Tj (C) 75 100 125 Figure 16. Output sink current vs temperature 12 1000 11 800 current (mA) Vccth2(V) @ Vcc = 15V 10 Typ. 9 8 7 -45 Typ. 600 400 200 -25 0 25 50 Tj (C) 75 100 125 0 -45 -25 0 25 50 Tj (C) 75 100 125 11/17 Typical characteristic L6386AD Figure 17. VCC UV hysteresis vs temperature 3 Vcchys (V) 2.5 Typ. 2 1.5 1 -45 12/17 -25 0 25 50 Tj (C) 75 100 125 L6386AD 6 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 13/17 Package mechanical data L6386AD Figure 18. SO-14 mechanical data and package dimensions mm inch DIM. MIN. TYP. MAX. MIN. TYP. MAX. A 1.35 1.75 0.053 0.069 A1 0.10 0.30 0.004 0.012 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.01 D (1) 8.55 8.75 0.337 0.344 E 3.80 4.0 0.150 0.157 e 1.27 0.050 H 5.8 6.20 0.228 0.244 h 0.25 0.50 0.01 0.02 L 0.40 1.27 0.016 0.050 k ddd OUTLINE AND MECHANICAL DATA 0 (min.), 8 (max.) 0.10 0.004 (1) "D" dimension does not include mold flash, protusions or gate burrs. Mold flash, protusions or gate burrs shall not exceed 0.15mm per side. SO-14 0016019 D 14/17 L6386AD 7 Order codes Order codes Table 7. Order codes Order codes Package Packaging L6386AD SO-14 Tube L6386AD013TR SO-14 Tape and reel 15/17 Revision history 8 L6386AD Revision history Table 8. 16/17 Document revision history Date Revision 14-Jul-2008 1 Changes First release L6386AD Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 17/17