1
2
3
4
8
7
6
5
V+
Out B
–In B
+In B
Out A
–In A
+In A
V–
OPA2353
SO-8, MSOP-8
A
B
1
2
3
4
8
7
6
5
NC
V+
Output
NC
NC
–In
+In
V–
OPA353
SO-8
High-Speed, Single-Supply, Rail-to-Rail
OPERATIONAL AMPLIFIERS
Micro
Amplifier
Series
© 1998 Burr-Brown Corporation PDS-1479B Printed in U.S.A. March, 1999
®
OPA353
OPA2353
OPA4353
FEATURES
RAIL-TO-RAIL INPUT
RAIL-TO-RAIL OUTPUT (within 10mV)
WIDE BANDWIDTH: 44MHz
HIGH SLEW RATE: 22V/µs
LOW NOISE: 5nV/Hz
LOW THD+NOISE: 0.0006%
UNITY-GAIN STABLE
Micro
SIZE PACKAGES
SINGLE, DUAL, AND QUAD
APPLICATIONS
CELL PHONE PA CONTROL LOOPS
DRIVING A/D CONVERTERS
VIDEO PROCESSING
DATA ACQUISITION
PROCESS CONTROL
AUDIO PROCESSING
COMMUNICATIONS
ACTIVE FILTERS
TEST EQUIPMENT
DESCRIPTION
OPA353 series rail-to-rail CMOS operational amplifi-
ers are designed for low cost, miniature applications.
They are optimized for low voltage, single-supply op-
eration. Rail-to-rail input/output, low noise (5nV/Hz),
and high speed operation (44MHz, 22V/µs) make them
ideal for driving sampling analog-to-digital converters.
They are also well suited for cell phone PA control
loops and video processing (75 drive capability) as
well as audio and general purpose applications. Single,
dual, and quad versions have identical specifications
for design flexibility.
The OPA353 series operates on a single supply as low as
2.5V with an input common-mode voltage range that
extends 300mV beyond the supply rails. Output voltage
swing is to within 10mV of the supply rails with a 10k
load. Dual and quad designs feature completely indepen-
dent circuitry for lowest crosstalk and freedom from
interaction.
The single (OPA353) packages are the tiny 5-lead SOT-
23-5 surface mount and SO-8 surface mount. The dual
(OPA2353) comes in the miniature MSOP-8 surface
mount and SO-8 surface mount. The quad (OPA4353)
packages are the space-saving SSOP-16 surface mount
and SO-14 surface mount. All are specified from –40°C
to +85°C and operate from –55°C to +125°C.
International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: (520) 746-1111
Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: (520) 889-1510 • Immediate Product Info: (800) 548-6132
(SO-14 package not shown)
OPA2353
OPA4353
OPA4353
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
Out D
–In D
+In D
–V
+In C
–In C
Out C
NC
Out A
–In A
+In A
+V
+In B
–In B
Out B
NC
OPA4353
SSOP-16
AD
BC
1
2
3
5
4
V+
–In
Out
V–
+In
OPA353
SOT-23-5
For most current data sheet and other product
information, visit www.burr-brown.com
SPICE Model available at www.burr-brown.com
SBOS103
2
OPA353, 2353, 4353
®
SPECIFICATIONS: VS = 2.7V to 5.5V
At TA = +25°C, RL = 1k connected to VS/ 2 and VOUT = VS/ 2, unless otherwise noted.
Boldface limits apply over the specified temperature range, TA = –40°C to +85°C. VS = 5V.
OPA353NA, UA
OPA2353EA, UA
OPA4353EA, UA
PARAMETER CONDITION MIN TYP(1) MAX UNITS
OFFSET VOLTAGE
Input Offset Voltage VOS VS = 5V ±3±8mV
TA = –40°C to +85°C±10 mV
vs Temperature TA = –40°C to +85°C±5µV/°C
vs Power Supply Rejection Ratio PSRR VS = 2.7V to 5.5V, VCM = 0V 40 150 µV/V
TA = –40°C to +85°CVS = 2.7V to 5.5V, VCM = 0V 175 µV/V
Channel Separation (dual, quad) dc 0.15 µV/V
INPUT BIAS CURRENT
Input Bias Current IB±0.5 ±10 pA
TA = –40°C to +85°CSee Typical Curve
Input Offset Current IOS ±0.5 ±10 pA
NOISE
Input Voltage Noise, f = 100Hz to 400kHz 4µVrms
Input Voltage Noise Density, f = 10kHz en7 nV/Hz
f = 100kHz 5 nV/Hz
Current Noise Density, f = 10kHz in4 fA/Hz
INPUT VOLTAGE RANGE
Common-Mode Voltage Range VCM –0.1 (V+) + 0.1 V
Common-Mode Rejection Ratio CMRR –0.1V < VCM < (V+) – 2.4V 76 86 dB
VS = 5V, –0.1V < V CM < 5.1V 60 74 dB
TA = –40°C to +85°CVS = 5V, –0.1V < VCM < 5.1V 58 dB
INPUT IMPEDANCE
Differential 1013 || 2.5 || pF
Common-Mode 1013 || 6.5 || pF
OPEN-LOOP GAIN
Open-Loop Voltage Gain AOL RL = 10k, 50mV < VO < (V+) – 50mV 100 122 dB
TA = –40°C to +85°CRL = 10k, 50mV < VO < (V+) – 50mV 100 dB
RL = 1k, 200mV < VO < (V+) – 200mV 100 120 dB
TA = –40°C to +85°CRL = 1k, 200mV < VO < (V+) – 200mV 100 dB
FREQUENCY RESPONSE CL = 100pF
Gain-Bandwidth Product GBW G = 1 44 MHz
Slew Rate SR G = 1 22 V/µs
Settling Time, 0.1% G = ±1, 2V Step 0.22 µs
0.01% G = ±1, 2V Step 0.5 µs
Overload Recovery Time VIN • G = VS0.1 µs
Total Harmonic Distortion + Noise THD+N
RL = 600, VO = 2.5Vp-p(2), G = 1, f = 1kHz
0.0006 %
Differential Gain Error G = 2, RL = 600, VO = 1.4V(3) 0.17 %
Differential Phase Error G = 2, RL = 600, VO = 1.4V(3) 0.17 deg
OUTPUT
Voltage Output Swing from Rail(4) VOUT RL = 10k, AOL 100dB 10 50 mV
TA = –40°C to +85°CRL = 10k Ω, AOL 100dB 50 mV
RL = 1kΩ, AOL 100dB 25 200 mV
TA = –40°C to +85°CRL = 1k , AOL 100dB 200 mV
Output Current IOUT ±40(5) mA
Short-Circuit Current ISC ±80 mA
Capacitive Load Drive CLOAD See Typical Curve
POWER SUPPLY
Operating Voltage Range VSTA = –40°C to +85°C 2.7 5.5 V
Minimum Operating Voltage 2.5 V
Quiescent Current (per amplifier) IQIO = 0 5.2 8 mA
TA = –40°C to +85°CIO = 0 9mA
TEMPERATURE RANGE
Specified Range –40 +85 °C
Operating Range –55 +125 °C
Storage Range –55 +125 °C
Thermal Resistance
θ
JA
SOT-23-5 200 °C/W
MSOP-8 Surface Mount 150 °C/W
SO-8 Surface Mount 150 °C/W
SSOP-16 Surface Mount 100 °C/W
SO-14 Surface Mount 100 °C/W
NOTES: (1) VS = +5V. (2) VOUT = 0.25V to 2.75V. (3) NTSC signal generator used. See Figure 6 for test circuit. (4) Output voltage swings are measured between
the output and power supply rails. (5) See typical performance curve, “Output Voltage Swing vs Output Swing.”
3
®
OPA353, 2353, 4353
PACKAGE/ORDERING INFORMATION
Supply Voltage ................................................................................... 5.5V
Signal Input Terminals, Voltage(2) .................. (V–) – 0.3V to (V+) + 0.3V
Current(2) .................................................... 10mA
Output Short-Circuit(3) .............................................................. Continuous
Operating Temperature .................................................. –55°C to +125°C
Storage Temperature .....................................................–55 °C to +125°C
Junction Temperature...................................................................... 150°C
Lead Temperature (soldering, 10s)................................................. 300°C
NOTES: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may de-
grade device reliability. (2) Input terminals are diode-clamped to the power
supply rails. Input signals that can swing more than 0.3V beyond the supply
rails should be current-limited to 10mA or less. (3) Short circuit to ground,
one amplifier per package.
ABSOLUTE MAXIMUM RATINGS(1)
PIN CONFIGURATION
Top View SO-14
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility
for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or
licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support
devices and/or systems.
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degrada-
tion to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
1
2
3
4
5
6
7
14
13
12
11
10
9
8
Out D
–In D
+In D
V–
+In C
–In C
Out C
Out A
–In A
+In A
V+
+In B
–In B
Out B
OPA4353
AD
BC
PACKAGE SPECIFIED
DRAWING TEMPERATURE PACKAGE ORDERING TRANSPORT
PRODUCT PACKAGE NUMBER(1) RANGE MARKING NUMBER(2) MEDIA
Single
OPA353NA 5-Lead SOT-23-5 331 –40°C to +85°C D53 OPA353NA /250 Tape and Reel
"""""OPA353NA /3K Tape and Reel
OPA353UA SO-8 Surface Mount 182 –40°C to +85°C OPA353UA OPA353UA Rails
"""""OPA353UA /2K5 Tape and Reel
Dual
OPA2353EA MSOP-8 Surface Mount 337 –40°C to +85°C E53 OPA2353EA/250 Tape and Reel
"""""OPA2353EA /2K5 Tape and Reel
OPA2353UA SO-8 Surface Mount 182 –40°C to +85°C OPA2353UA OPA2353UA Rails
"""""OPA2353UA /2K5 Tape and Reel
Quad
OPA4353EA SSOP-16 Surface Mount 322 –40°C to +85°C OPA4353EA OPA4353EA/250 Tape and Reel
"""""OPA4353EA /2K5 Tape and Reel
OPA4353UA SO-14 Surface Mount 235 –40°C to +85°C OPA4353UA OPA4353UA Rails
"""""OPA4353UA /2K5 Tape and Reel
NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) Models with a slash (/) are
available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of “OPA2353EA/2K5” will get a single
2500-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown IC Data Book.
4
OPA353, 2353, 4353
®
TYPICAL PERFORMANCE CURVES
At TA = +25°C, VS = +5V, and RL = 1k connected to VS/2, unless otherwise noted.
OPEN-LOOP GAIN/PHASE vs FREQUENCY
0.1 1
160
140
120
100
80
60
40
20
0
Voltage Gain (dB)
0
–45
–90
–135
–180
Phase (°)
Frequency (Hz)
10 100 1k 10k 100k 1M 10M 100M
G
φ
POWER SUPPLY AND COMMON-MODE
REJECTION RATIO vs FREQUENCY
100
90
80
70
60
50
40
30
20
10
0
PSRR, CMRR (dB)
Frequency (Hz)
10 100 1k 10k 100k 1M 10M
PSRR
CMRR
(VS = +5V
VCM = –0.1V to 5.1V)
INPUT VOLTAGE AND CURRENT NOISE
SPECTRAL DENSITY vs FREQUENCY
100k
10k
1k
100
10
1
10k
1k
100
10
1
0.1
Voltage Noise (nVHz)
Frequency (Hz)
10 100 1k 10k 100k 1M 10M
Current Noise (fAHz)
Voltage Noise
Current Noise
HARMONIC DISTORTION + NOISE vs FREQUENCY
1
(–40dBc)
0.1
(–60dBc)
0.01
(–80dBc)
0.001
(–100dBc)
0.0001
(–120dBc)
Harmonic Distortion (%)
Frequency (Hz)
1k 10k 100k 1M
G = 1
V
O
= 2.5Vp-p
R
L
= 600
3rd Harmonic 2nd Harmonic
TOTAL HARMONIC DISTORTION + NOISE
vs FREQUENCY
1
0.1
0.01
0.001
0.0001
THD+N (%)
Frequency (Hz)
10 100 1k 10k 100k
R
L
= 600
G = 100, 3Vp-p (V
O
= 1V to 4V)
G = 10, 3Vp-p (V
O
= 1V to 4V)
G = 1, 3Vp-p (V
O
= 1V to 4V)
Input goes through transition region
G = 1, 2.5Vp-p (V
O
= 0.25V to 2.75V)
Input does NOT go through transition region
CHANNEL SEPARATION vs FREQUENCY
Frequency (Hz)
Channel Separation (dB)
140
130
120
110
100
90
80
70
60 10010 1k 1M100k10k 10M
Dual and Quad
Versions
5
®
OPA353, 2353, 4353
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = +5V, and RL = 1k connected to VS/2, unless otherwise noted.
DIFFERENTIAL GAIN/PHASE vs RESISTIVE LOAD
0.5
0.4
0.3
0.2
0.1
0
Differential Gain (%)
Differential Phase (°)
Resistive Load ()
0 100 200 300 500400 600 800700 900 1000
G = 2
V
O
= 1.4V
NTSC Signal Generator
See Figure 6 for test circuit.
Phase
Gain
OPEN-LOOP GAIN vs TEMPERATURE
130
125
120
115
110
Open-Loop Gain (dB)
Temperature (°C)
–75 –50 –25 0 25 50 75 100 125
R
L
= 600
R
L
= 1k
R
L
= 10k
COMMON-MODE AND POWER SUPPLY
REJECTION RATIO vs TEMPERATURE
90
80
70
60
50
CMRR (dB)
110
100
90
80
70
PSRR (dB)
Temperature (°C)
–75 –50 –25 0 25 50 75 100 125
CMRR, V
S
= 5V
(V
CM
= –0.1V to +5.1V)
PSRR
SLEW RATE vs TEMPERATURE
Temperature (°C)
Slew Rate (V/µs)
40
35
30
25
20
15
10
5
0–75 –50 –25 0 25 50 75 100 125
Negative Slew Rate
Positive Slew Rate
QUIESCENT CURRENT AND
SHORT-CIRCUIT CURRENT vs TEMPERATURE
Temperature (°C)
Quiescent Current (mA)
7.0
6.5
6.0
5.5
5.0
4.5
4.0
3.5
100
90
80
70
60
50
40
30
Short-Circuit Current (mA)
–75 –50 –25 0 25 50 75 100 125
I
Q
+I
SC
–I
SC
QUIESCENT CURRENT vs SUPPLY VOLTAGE
Supply Voltage (V)
Quiescent Current (mA)
6.0
5.5
5.0
4.5
4.0
3.5
3.02.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
Per Amplifier
6
OPA353, 2353, 4353
®
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = +5V, and RL = 1k connected to VS/2, unless otherwise noted.
INPUT BIAS CURRENT vs TEMPERATURE
Input Bias Current (pA)
Temperature (°C)
–75 –50 –25 0 25 50 75 100 125
1k
100
10
1
0.1
INPUT BIAS CURRENT
vs INPUT COMMON-MODE VOLTAGE
Common-Mode Voltage (V)
Input Bias Current (pA)
1.5
1.0
0.5
0.0
–0.5
–0.5 0.0 0.5 1.0 2.01.5 2.5 3.0 3.5 4.0 5.04.5 5.5
CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY
Frequency (Hz)
Output Impedance ()
100
10
1
0.1
0.01
0.001
0.0001 1 10 100 1k 10k 100k 1M 10M 100M
G = 100
G = 10
G = 1
MAXIMUM OUTPUT VOLTAGE vs FREQUENCY
100M1M 10M
Frequency (Hz)
100k
6
5
4
3
2
1
0
Output Voltage (Vp-p)
Maximum output
voltage without
slew rate-induced
distortion.
V
S
= 2.7V
V
S
= 5.5V
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
Output Current (mA)
Output Voltage (V)
V+
(V+)–1
(V+)–2
(V–)+2
(V–)+1
(V–) 0±10 ±20 ±30 ±40
+25°C
+125°C–55°C
–55°C
+125°C+25°C
Depending on circuit configuration
(including closed-loop gain) performance
may be degraded in shaded region.
OPEN-LOOP GAIN vs OUTPUT VOLTAGE SWING
140
130
120
110
100
90
80
70
60
Open-Loop Gain (dB)
Output Voltage Swing from Supply Rails (mV)
0 20 40 60 10080 120 160140 180 200
I
OUT
= 4.2mA
I
OUT
= 250µAI
OUT
= 2.5mA
7
®
OPA353, 2353, 4353
TYPICAL PERFORMANCE CURVES (CONT)
At TA = +25°C, VS = +5V, and RL = 1k connected to VS/2, unless otherwise noted.
SMALL-SIGNAL STEP RESPONSE
CL = 100pF
100ns/div
50mV/div
LARGE-SIGNAL STEP RESPONSE
CL = 100pF
200ns/div
1V/div
Offset Voltage Drift (µV/°C)
OFFSET VOLTAGE DRIFT
PRODUCTION DISTRIBUTION
35
30
25
20
15
10
5
00123456789101112131415
Percent of Amplifiers (%)
Typical production
distribution of
packaged units.
SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE
1M100 1k 10k 100k
Load Capacitance (pF)
10
80
70
60
50
40
30
20
10
0
Overshoot (%)
G = 1
G = –1
G = ±10
SETTLING TIME vs CLOSED-LOOP GAIN
10
1
0.1
Settling Time (µs)
Closed-Loop Gain (V/V)
±1±10 ±100
0.1%
0.01%
Offset Voltage (mV)
OFFSET VOLTAGE PRODUCTION DISTRIBUTION
25
20
15
10
5
0–8 –7 –6 –5 4 –3 –2 –1 0 1 2 3 4 5 6 7 8
Percent of Units (%)
Typical production
distribution of
packaged units.
8
OPA353, 2353, 4353
®
APPLICATIONS INFORMATION
OPA353 series op amps are fabricated on a state-of-the-art
0.6 micron CMOS process. They are unity-gain stable and
suitable for a wide range of general purpose applications.
Rail-to-rail input/output make them ideal for driving sam-
pling A/D converters. They are well suited for controlling
the output power in cell phones. These applications often
require high speed and low noise. In addition, the OPA353
series offers a low cost solution for general purpose and
consumer video applications (75 drive capability).
Excellent ac performance makes the OPA353 series well
suited for audio applications. Their bandwidth, slew rate,
low noise (5nV/Hz), low THD (0.0006%), and small pack-
age options are ideal for these applications. The class AB
output stage is capable of driving 600 loads connected to
any point between V+ and ground.
Rail-to-rail input and output swing significantly increases
dynamic range, especially in low voltage supply applica-
tions. Figure 1 shows the input and output waveforms for
the OPA353 in unity-gain configuration. Operation is
from a single +5V supply with a 1k load connected to
VS/2. The input is a 5Vp-p sinusoid. Output voltage is
approximately 4.95Vp-p.
Power supply pins should be bypassed with 0.01µF ceramic
capacitors.
OPERATING VOLTAGE
OPA353 series op amps are fully specified from +2.7V to
+5.5V. However, supply voltage may range from +2.5V to
+5.5V. Parameters are guaranteed over the specified supply
range—a unique feature of the OPA353 series. In addition,
many specifications apply from –40°C to +85°C. Most
behavior remains virtually unchanged throughout the full
operating voltage range. Parameters which vary signifi-
cantly with operating voltages or temperature are shown in
the typical performance curves.
RAIL-TO-RAIL INPUT
The guaranteed input common-mode voltage range of the
OPA353 series extends 100mV beyond the supply rails. This
is achieved with a complementary input stage—an
N-channel input differential pair in parallel with a P-channel
differential pair (see Figure 2). The N-channel pair is active
for input voltages close to the positive rail, typically
(V+) – 1.8V to 100mV above the positive supply, while the
P-channel pair is on for inputs from 100mV below the
negative supply to approximately (V+) – 1.8V. There is a
small transition region, typically (V+) – 2V to (V+) – 1.6V, in
which both pairs are on. This 400mV transition region can
vary ±400mV with process variation. Thus, the transition
region (both input stages on) can range from (V+) – 2.4V to
(V+) – 2.0V on the low end, up to (V+) – 1.6V to (V+) – 1.2V
on the high end.
FIGURE 2. Simplified Schematic.
V
BIAS1
V
BIAS2
V
IN
+V
IN
Class AB
Control
Circuitry V
O
V–
(Ground)
V+
Reference
Current
0
5V
VS = +5, G = +1, RL = 1k
VIN
1.25V/div
FIGURE 1. Rail-to-Rail Input and Output.
5V
0
VOUT
9
®
OPA353, 2353, 4353
A double-folded cascode adds the signal from the two input
pairs and presents a differential signal to the class AB output
stage. Normally, input bias current is approximately 500fA.
However, large inputs (greater than 300mV beyond the
supply rails) can turn on the OPA353’s input protection
diodes, causing excessive current to flow in or out of the
input pins. Momentary voltages greater than 300mV beyond
the power supply can be tolerated if the current on the input
pins is limited to 10mA. This is easily accomplished with an
input resistor as shown in Figure 3. Many input signals are
inherently current-limited to less than 10mA, therefore, a
limiting resistor is not required.
FEEDBACK CAPACITOR IMPROVES RESPONSE
For optimum settling time and stability with high-imped-
ance feedback networks, it may be necessary to add a
feedback capacitor across the feedback resistor, RF, as
shown in Figure 4. This capacitor compensates for the zero
created by the feedback network impedance and the
OPA353’s input capacitance (and any parasitic layout
capacitance). The effect becomes more significant with
higher impedance networks.
FIGURE 3. Input Current Protection for Voltages Exceeding
the Supply Voltage.
RAIL-TO-RAIL OUTPUT
A class AB output stage with common-source transistors is
used to achieve rail-to-rail output. For light resistive loads
(>10k), the output voltage swing is typically ten millivolts
from the supply rails. With heavier resistive loads (600 to
10k), the output can swing to within a few tens of milli-
volts from the supply rails and maintain high open-loop
gain. See the typical performance curves “Output Voltage
Swing vs Output Current” and “Open-Loop Gain vs Output
Voltage.”
CAPACITIVE LOAD AND STABILITY
OPA353 series op amps can drive a wide range of capacitive
loads. However, all op amps under certain conditions may
become unstable. Op amp configuration, gain, and load
value are just a few of the factors to consider when determin-
ing stability. An op amp in unity gain configuration is the
most susceptible to the effects of capacitive load. The
capacitive load reacts with the op amp’s output impedance,
along with any additional load resistance, to create a pole in
the small-signal response which degrades the phase margin.
In unity gain, OPA353 series op amps perform well with
large capacitive loads. Increasing gain enhances the
amplifier’s ability to drive more capacitance. The typical
performance curve “Small-Signal Overshoot vs Capacitive
Load” shows performance with a 1k resistive load. In-
creasing load resistance improves capacitive load drive ca-
pability.
FIGURE 4. Feedback Capacitor Improves Dynamic Perfor-
mance.
It is suggested that a variable capacitor be used for the
feedback capacitor since input capacitance may vary be-
tween op amps and layout capacitance is difficult to
determine. For the circuit shown in Figure 4, the value of
the variable feedback capacitor should be chosen so that
the input resistance times the input capacitance of the
OPA353 (typically 9pF) plus the estimated parasitic layout
capacitance equals the feedback capacitor times the feed-
back resistor:
RIN • CIN = RF • CF
where CIN is equal to the OPA353’s input capacitance
(sum of differential and common-mode) plus the layout
capacitance. The capacitor can be varied until optimum
performance is obtained.
DRIVING A/D CONVERTERS
OPA353 series op amps are optimized for driving medium
speed (up to 500kHz) sampling A/D converters. However,
they also offer excellent performance for higher speed
converters. The OPA353 series provides an effective means
of buffering the A/D’s input capacitance and resulting
charge injection while providing signal gain. For applica-
tions requiring high accuracy, the OPA350 series is recom-
mended.
5k
OPAx353
10mA max
V+
V
IN
V
OUT
I
OVERLOAD
OPA353
V+
V
OUT
V
IN
R
IN
R
IN
• C
IN
= R
F
C
F
R
F
C
L
C
IN
C
IN
C
F
Where C
IN
is equal to the OPA353’s input
capacitance (approximately 9pF) plus any
parastic layout capacitance.
10
OPA353, 2353, 4353
®
Figure 5 shows the OPA353 driving an ADS7861. The
ADS7861 is a dual, 12-bit, 500kHz sampling converter in
the small SSOP-24 package. When used with the miniature
package options of the OPA353 series, the combination is
ideal for space-limited and low power applications. For
further information consult the ADS7861 data sheet.
OUTPUT IMPEDANCE
The low frequency open-loop output impedance of the
OPA353’s common-source output stage is approximately
1k. When the op amp is connected with feedback, this
value is reduced significantly by the loop gain of the op
amp. For example, with 122dB of open-loop gain, the
output impedance is reduced in unity-gain to less than
0.001. For each decade rise in the closed-loop gain, the
loop gain is reduced by the same amount which results in
a ten-fold increase in output impedance (see the typical
performance curve, “Output Impedance vs Frequency”).
At higher frequencies, the output impedance will rise as
the open-loop gain of the op amp drops. However, at these
frequencies the output also becomes capacitive due to
parasitic capacitance. This prevents the output impedance
from becoming too high, which can cause stability prob-
lems when driving capacitive loads. As mentioned previ-
ously, the OPA353 has excellent capacitive load drive
capability for an op amp with its bandwidth.
VIDEO LINE DRIVER
Figure 6 shows a circuit for a single supply, G = 2 com-
posite video line driver. The synchronized outputs of a
composite video line driver extend below ground. As
shown, the input to the op amp should be ac-coupled and
shifted positively to provide adequate signal swing to
account for these negative signals in a single-supply con-
figuration.
The input is terminated with a 75 resistor and ac-coupled
with a 47µF capacitor to a voltage divider that provides the
dc bias point to the input. In Figure 6, this point is
approximately (V–) + 1.7V. Setting the optimal bias point
requires some understanding of the nature of composite
video signals. For best performance, one should be careful
to avoid the distortion caused by the transition region of
the OPA353’s complementary input stage. Refer to the
discussion of rail-to-rail input.
FIGURE 5. OPA4353 Driving Sampling A/D Converter.
1/4
OPA4353
V
IN
B1
2
3
4
2k
2k
C
B1
CH B1+
CH B1–
CH B0+
CH B0–
CH A1+
CH A1–
CH A0+
CH A0–
REF
IN
REF
OUT
Serial Data A
Serial Data B
BUSY
CLOCK
CS
RD
CONVST
A0
M0
M1
2
3
4
5
6
7
8
9
10
11
23
22
21
20
19
18
17
16
15
14
1/4
OPA4353
V
IN
B0
+5V
6
5
2k
2k
C
B0
1/4
OPA4353
V
IN
A1
9
10
8
7
2k
2k
C
A1
1/4
OPA4353
V
IN
A0
14
11
112
2k
2k
C
A0
0.1µF 0.1µF
+V
A
+V
D
24 13
Serial
Interface
DGND AGND
ADS7861
V
IN
= 0V to 2.45V for 0V to 4.9V output.
Choose C
B1
, C
B0
, C
A1
, C
A0
to filter high frequency noise.
11
®
OPA353, 2353, 4353
FIGURE 6. Single-Supply Video Line Driver.
FIGURE 7. Two Op-Amp Instrumentation Amplifier With Improved High Frequency Common-Mode Rejection.
OPA353 V
O
10M
<1pF (prevents gain peaking)
+V
λ
FIGURE 9. 10kHz Low-Pass Filter.
FIGURE 8. Transimpedance Amplifier.
FIGURE 10. 10kHz High-Pass Filter.
OPA353
+5V
V
OUT
+5V (pin 7)
Video
In
R
OUT
R
L
Cable
R
F
1k
R
G
1k
R
4
5k
R
3
5k
C
3
10µF
0.1µF10µF
+
6
7
4
C
4
0.1µF
C
5
1000µF
C
2
47µF
R
2
5k
R
1
75
C
1
220µF
+2.5V
V
IN
C
2
270pF
C
1
1830pF
–2.5V
R
2
49.9k
R
L
20k
OPA353 V
OUT
R
1
10.5k
+2.5V
V
IN
R
2
19.6k
R
1
2.74k
–2.5V
C
2
1nF
R
L
20k
OPA353 V
OUT
C
1
4.7µF
1/2
OPA2353
1/2
OPA2353
R
3
25k
R
2
25k
R
G
R
1
100k
R
4
100k
R
L
10k
V
OUT
50k
G = 5 + 200k
R
G
+5V
+5V
REF1004-2.5
4
8
(2.5V)
PACKAGE OPTION ADDENDUM
www.ti.com 16-Aug-2012
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
OPA2353EA/250 ACTIVE VSSOP DGK 8 250 Green (RoHS
& no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR
OPA2353EA/250G4 ACTIVE VSSOP DGK 8 250 Green (RoHS
& no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR
OPA2353EA/2K5 ACTIVE VSSOP DGK 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR
OPA2353EA/2K5G4 ACTIVE VSSOP DGK 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAUAGLevel-2-260C-1 YEAR
OPA2353UA ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA2353UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA2353UA/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA2353UAG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA353NA/250 ACTIVE SOT-23 DBV 5 250 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA353NA/250G4 ACTIVE SOT-23 DBV 5 250 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA353NA/3K ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA353NA/3KG4 ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA353UA ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA353UA/2K5 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA353UA/2K5G4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA353UAG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA4353EA/250 ACTIVE SSOP DBQ 16 250 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
PACKAGE OPTION ADDENDUM
www.ti.com 16-Aug-2012
Addendum-Page 2
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
OPA4353EA/250G4 ACTIVE SSOP DBQ 16 250 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA4353EA/2K5 ACTIVE SSOP DBQ 16 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA4353EA/2K5G4 ACTIVE SSOP DBQ 16 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA4353UA ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA4353UA/2K5 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA4353UA/2K5G4 ACTIVE SOIC D 14 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
OPA4353UAG4 ACTIVE SOIC D 14 50 Green (RoHS
& no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
PACKAGE OPTION ADDENDUM
www.ti.com 16-Aug-2012
Addendum-Page 3
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
OPA2353EA/250 VSSOP DGK 8 250 180.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
OPA2353EA/2K5 VSSOP DGK 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
OPA2353UA/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
OPA353UA/2K5 SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
OPA4353EA/250 SSOP DBQ 16 250 180.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
OPA4353EA/2K5 SSOP DBQ 16 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
OPA4353UA/2K5 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 16-Aug-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
OPA2353EA/250 VSSOP DGK 8 250 210.0 185.0 35.0
OPA2353EA/2K5 VSSOP DGK 8 2500 367.0 367.0 35.0
OPA2353UA/2K5 SOIC D 8 2500 367.0 367.0 35.0
OPA353UA/2K5 SOIC D 8 2500 367.0 367.0 35.0
OPA4353EA/250 SSOP DBQ 16 250 210.0 185.0 35.0
OPA4353EA/2K5 SSOP DBQ 16 2500 367.0 367.0 35.0
OPA4353UA/2K5 SOIC D 14 2500 367.0 367.0 38.0
PACKAGE MATERIALS INFORMATION
www.ti.com 16-Aug-2012
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated