DS75176B/DS75176BT
Multipoint RS-485/RS-422 Transceivers
General Description
The DS75176B is a high speed differential TRI-STATE®
bus/line transceiver designed to meet the requirements of
EIA standard RS485 with extended common mode range
(+12V to −7V), for multipoint data transmission. In addition, it
is compatible with RS-422.
The driver and receiver outputs feature TRI-STATE capabil-
ity, for the driver outputs over the entire common mode
range of +12V to −7V. Bus contention or fault situations that
cause excessive power dissipation within the device are
handled by a thermal shutdown circuit, which forces the
driver outputs into the high impedance state.
DC specifications are guaranteed over the 0 to 70˚C tem-
perature and 4.75V to 5.25V supply voltage range.
Features
nMeets EIA standard RS485 for multipoint bus
transmission and is compatible with RS-422.
nSmall Outline (SO) Package option available for
minimum board space.
n22 ns driver propagation delays.
nSingle +5V supply.
n−7V to +12V bus common mode range permits ±7V
ground difference between devices on the bus.
nThermal shutdown protection.
nHigh impedance to bus with driver in TRI-STATE or with
power off, over the entire common mode range allows
the unused devices on the bus to be powered down.
nPin out compatible with DS3695/A and SN75176A/B.
nCombined impedance of a driver output and receiver
input is less than one RS485 unit load, allowing up to 32
transceivers on the bus.
n70 mV typical receiver hysteresis.
Connection and Logic Diagram
TRI-STATE®is a registered trademark of National Semiconductor Corp.
DS008759-1
Top View
Order Number DS75176BN, DS75176BTN, DS75176BM or DS75176BTM
See NS Package Number N08E or M08A
July 1998
DS75176B/DS75176BT Multipoint RS-485/RS-422 Transceivers
© 1999 National Semiconductor Corporation DS008759 www.national.com
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage, V
CC
7V
Control Input Voltages 7V
Driver Input Voltage 7V
Driver Output Voltages +15V/ −10V
Receiver Input Voltages (DS75176B) +15V/ −10V
Receiver Output Voltage 5.5V
Continuous Power Dissipation @25˚C
for M Package 675 mW (Note 5)
for N Package 900 mW (Note 4)
Storage Temperature Range −65˚C to +150˚C
Lead Temperature
(Soldering, 4 seconds) 260˚C
Recommended Operating
Conditions
Min Max Units
Supply Voltage, V
CC
4.75 5.25 V
Voltage at Any Bus Terminal −7 +12 V
(Separate or Common Mode)
Operating Free Air Temperature T
A
DS75176B 0 +70 ˚C
DS75176BT −40 +85 ˚C
Differential Input Voltage,
VID (Note 6) −12 +12 V
Electrical Characteristics (Notes 2, 3)
0˚C T
A
70˚C, 4.75V <V
CC
<5.25V unless otherwise specified
Symbol Parameter Conditions Min Typ Max Units
V
OD1
Differential Driver Output I
O
=0 5 V
Voltage (Unloaded)
V
OD2
Differential Driver Output (
Figure 1
) R=50; (RS-422) (Note 7) 2 V
Voltage (with Load) R = 27; (RS-485) 1.5 V
V
OD
Change in Magnitude of Driver
Differential Output Voltage For 0.2 V
Complementary Output States
V
OC
Driver Common Mode Output (
Figure 1
) R=273.0 V
Voltage
|V
OC
| Change in Magnitude of Driver
Common Mode Output Voltage 0.2 V
For Complementary Output
States
V
IH
Input High Voltage 2V
V
IL
Input Low Voltage DI, DE, 0.8
V
CL
Input Clamp Voltage RE , E I
IN
= −18 mA −1.5
I
IL
Input Low Current V
IL
= 0.4V −200 µA
I
IH
Input High Current V
IH
= 2.4V 20 µA
I
IN
Input DO/RI, DO/RI V
CC
= 0V or 5.25V V
IN
= 12V +1.0 mA
Current DE = 0V V
IN
= −7V −0.8 mA
V
TH
Differential Input Threshold −7V V
CM
+ 12V −0.2 +0.2 V
Voltage for Receiver
V
TH
Receiver Input Hysteresis V
CM
=0V 70 mV
V
OH
Receiver Output High Voltage I
OH
= −400 µA 2.7 V
V
OL
Output Low Voltage RO I
OL
= 16 mA (Note 7) 0.5 V
I
OZR
OFF-State (High Impedance) V
CC
= Max ±20 µA
Output Current at Receiver 0.4V V
O
2.4V
R
IN
Receiver Input Resistance −7V V
CM
+12V 12 k
I
CC
Supply Current No Load Driver Outputs Enabled 55 mA
(Note 7) Driver Outputs Disabled 35 mA
I
OSD
Driver Short-Circuit V
O
= −7V (Note 7) −250 mA
Output Current V
O
= +12V (Note 7) +250 mA
www.national.com 2
Electrical Characteristics (Notes 2, 3) (Continued)
0˚C T
A
70˚C, 4.75V <V
CC
<5.25V unless otherwise specified
Symbol Parameter Conditions Min Typ Max Units
I
OSR
Receiver Short-Circuit V
O
= 0V −15 −85 mA
Output Current
Note 1: “Absolute Maximum Ratings” are those beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should
be operated at these limits. The tables of “Electrical Characteristics” provide conditions for actual device operation.
Note 2: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise specified.
Note 3: All typicals are given for VCC = 5V and TA= 25˚C.
Note 4: Derate linearly at 5.56 mW/˚C to 650 mW at 70˚C.
Note 5: Derate linearly 6.11 mW/˚C to 400 mW at 70˚C.
Note 6: Differential - Input/Output bus voltage is measured at the noninverting terminal A with respect to the inverting terminal B.
Note 7: All worst case parameters for which note 7 is applied, must be increased by 10%for DS75176BT. The other parameters remain valid for −40˚C <TA
<+85˚C.
Switching Characteristics
V
CC
= 5.0V, T
A
= 25˚C
Symbol Parameter Conditions Min Typ Max Units
t
PLH
Driver Input to Output R
LDIFF
=6012 22 ns
t
PHL
Driver Input to Output C
L1
=C
L2
= 100 pF 17 22 ns
t
r
Driver Rise Time R
LDIFF
=6018 ns
t
f
Driver Fall Time C
L1
=C
L2
= 100 pF 18 ns
(
Figure 3
and
Figure 5
)
t
ZH
Driver Enable to Output High C
L
= 100 pF (
Figure 4
and
Figure 6
)S1
Open 29 100 ns
t
ZL
Driver Enable to Output Low C
L
= 100 pF (
Figure 4
and
Figure 6
)S2
Open 31 60 ns
t
LZ
Driver Disable Time from Low C
L
=15pF(
Figure 4
and
Figure 6
)S2
Open 13 30 ns
t
HZ
Driver Disable Time from High C
L
=15pF(
Figure 4
and
Figure 6
)S1
Open 19 200 ns
t
PLH
Receiver Input to Output C
L
=15pF(
Figure 2
and
Figure 7
)3037ns
t
PHL
Receiver Input to Output S1 and S2 Closed 32 37 ns
t
ZL
Receiver Enable to Output Low C
L
=15pF(
Figure 2
and
Figure 8
)S2
Open 15 20 ns
t
ZH
Receiver Enable to Output High C
L
=15pF(
Figure 2
and
Figure 8
)S1
Open 11 20 ns
t
LZ
Receiver Disable from Low C
L
=15pF(
Figure 2
and
Figure 8
)S2
Open 28 32 ns
t
HZ
Receiver Disable from High C
L
=15pF(
Figure 2
and
Figure 8
)S1
Open 13 35 ns
www.national.com3
AC Test Circuits
Switching Time Waveforms
DS008759-2
FIGURE 1.
DS008759-3
Note: S1 and S2 of load circuit are closed except as otherwise mentioned.
FIGURE 2.
DS008759-4
FIGURE 3.
DS008759-5
Note: Unless otherwise specified the switches are closed.
FIGURE 4.
DS008759-6
FIGURE 5. Driver Propagation Delays and Transition Times
www.national.com 4
Switching Time Waveforms (Continued)
Function Tables
DS75176B Transmitting
Inputs Line Outputs
RE DE DI Condition DO DO
X 1 1 No Fault 0 1
X 1 0 No Fault 1 0
X0X X ZZ
X 1 X Fault Z Z
DS008759-7
FIGURE 6. Driver Enable and Disable Times
DS008759-8
Note: Differential input voltage may may be realized by grounding RI and pulsing RI between +2.5V and −2.5V
FIGURE 7. Receiver Propagation Delays
DS008759-9
FIGURE 8. Receiver Enable and Disable Times
www.national.com5
Function Tables (Continued)
DS75176B Receiving
Inputs Outputs
RE DE RI-RI RO
00 +0.2V 1
00 −0.2V 0
0 0 Inputs Open** 1
10 X Z
X Don’t care condition
Z High impedance state
Fault Improper line conditons causing excessive power dissipation in the driver, such as shorts or bus contention
situations
**This is a fail safe condition
Typical Application
DS008759-11
www.national.com 6
Physical Dimensions inches (millimeters) unless otherwise noted
Lit. # 103669
Molded Dual-In-Line Package (N)
Order Number DS75176BN or DS75176BTN
NS Package Number N08E
www.national.com7
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DE-
VICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMI-
CONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or sys-
tems which, (a) are intended for surgical implant into
the body, or (b) support or sustain life, and whose fail-
ure to perform when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
2. A critical component is any component of a life support
device or system whose failure to perform can be rea-
sonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
www.national.com
National Semiconductor
Europe Fax: +49 (0) 1 80-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: sea.support@nsc.com
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
DS75176B/DS75176BT Multipoint RS-485/RS-422 Transceivers
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Design Purchasing Quality Company Jobs
Products > Analog - Interface > Data Transmission Circuits > RS-485 > DS75176B
DS75176B Multipoint RS-485/RS-422 Transceivers
Generic P/N 75176B
Contents
General Description
Features
Datasheet
Package Availability, Models, Samples & Pricing
Application Notes
Parametric Table
Number of Drivers 1
Number of Receivers 1
Supply Voltage 5 V
Process Bipolar
General Description
The DS75176B is a high speed differential TRI-STATE bus/line transceiver designed to
meet the requirements of EIA standard RS485 with extended common mode range (+12V
to -7V), for multipoint data transmission. In addition, it is compatible with RS-422.
The driver and receiver outputs feature TRI-STATE capability, for the driver outputs over
the entire common mode range of +12V to -7V. Bus contention or fault situations that cause
excessive power dissipation within the device are handled by a thermal shutdown circuit,
which forces the driver outputs into the high impedance state.
DC specifications are guaranteed over the 0 to 70°C temperature and 4.75V to 5.25V supply
voltage range.
Features
Product Folder
1 of 3 05-Aug-2000 12:43 PM
National P/N DS75176B - Multipoint RS-485/RS-422 Transceivers file:////roarer/root/data13/imaging/BIT...04/08032000/NATL/08022000/DS75176B.html
Meets EIA standard RS485 for multipoint bus transmission and is compatible with
RS-422.
Small Outline (SO) Package option available for minimum board space.
22 ns driver propagation delays.
Single +5V supply.
-7V to +12V bus common mode range permits ±7V ground difference between
devices on the bus.
Thermal shutdown protection.
High impedance to bus with driver in TRI-STATE or with power off, over the entire
common mode range allows the unused devices on the bus to be powered down.
Pin out compatible with DS3695/A and SN75176A/B.
Combined impedance of a driver output and receiver input is less than one RS485
unit load, allowing up to 32 transceivers on the bus.
70 mV typical receiver hysteresis.
Datasheet
Title Size
(in
Kbytes) Date View
Online Download
Receive
DS75176B/DS75176BT Multipoint RS-485/RS-422
Transceivers 209
Kbytes 4-Mar-99 View
Online Download
Receive
via
Email
DS75176B/DS75176BT Multipoint RS-485/RS-422
Transceivers (JAPANESE)281
Kbytes
Please use Adobe Acrobat to view PDF file(s).
If you have trouble printing, see Printing Problems.
Package Availability, Models, Samples & Pricing
Download
2 of 3 05-Aug-2000 12:43 PM
National P/N DS75176B - Multipoint RS-485/RS-422 Transceivers file:////roarer/root/data13/imaging/BIT...04/08032000/NATL/08022000/DS75176B.html
Part Number Package Status Models Samples
&
Electronic
Orders
Budgetary
Pricing Std
Pack
Size
Type #
pins SPICE IBIS Quantity $US
each
DS75176BM SOIC
NARROW 8Full
production N/A N/A .2500+ $0.4730 tube
of
95
DS75176BMX SOIC
NARROW 8Full
production N/A N/A .2500+ $0.4730 reel
of
2500
DS75176BN MDIP 8Full
production N/A N/A .2500+ $0.4730 tube
of
40
[logo]¢U¢Z¢2¢T
DS75176B
MDA die Full
production N/A N/A . N/A
Application Notes
Title Size
(in Kbytes) Date View
Online Download Receive via
Email
AN-915: Application Note 915
Automotive Physical Layer SAE J1708
and the DS36277 66 Kbytes 5-Oct-98 View
Online Download Receive via
Email
AN-1057: Application Note 1057 Ten
Ways to Bulletproof RS-485 Interfaces 155 Kbytes 5-Oct-98 View
Online Download Receive via
Email
AN-741: Differentiating FDDI
Concentrators 276 Kbytes 5-Aug-95 View
Online Download Receive via
Email
Please use Adobe Acrobat to view PDF file(s).
If you have trouble printing, see Printing Problems.
[Information as of 2-Aug-2000]
Quick Search
Parametric
Search System
Diagrams Product
Tree Home
About Languages . About the Site . About "Cookies"
National is QS 9000 Certified . Privacy/Security
Copyright © National Semiconductor Corporation
Preferences . Feedback
Order Parts
Order Parts
Order Parts
3 of 3 05-Aug-2000 12:43 PM
National P/N DS75176B - Multipoint RS-485/RS-422 Transceivers file:////roarer/root/data13/imaging/BIT...04/08032000/NATL/08022000/DS75176B.html