74ACT11245
OCTAL BUS TRANSCEIVER
WITH 3-STATE OUTPUTS
SCAS031C – JULY 1987 – REVISED APRIL 1996
1
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
D
3-State Outputs Drive Bus Lines Directly
D
Inputs Are TTL-Voltage Compatible
D
Flow-Through Architecture Optimizes
PCB Layout
D
Center-Pin VCC and GND Configurations
Minimize High-Speed Switching Noise
D
EPIC
t
(Enhanced-Performance Implanted
CMOS) 1-
m
m Process
D
500-mA Typical Latch-Up Immunity at
125°C
D
Package Options Include Plastic
Small-Outline (DW), Shrink Small-Outline
(DB), and Thin Shrink Small-Outline (PW)
Packages, and Standard Plastic 300-mil
DIPs (NT)
description
The octal bus transceiver is designed for asynchronous two-way communication between data buses. The
control-function implementation minimizes external timing requirements.
The device allows data transmission from the A bus to the B bus or from the B bus to the A bus, depending on
the logic level at the direction-control (DIR) input. The output-enable (OE) input can be used to disable the
device so that the buses are effectively isolated.
The 74ACT11245 is characterized for operation from –40°C to 85°C.
FUNCTION TABLE
OUTPUT
ENABLE
OE
DIRECTION
CONTROL
DIR OUTPUT
L L B data to A bus
L H A data to B bus
H X Isolation
Copyright 1996, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
EPIC is a trademark of Texas Instruments Incorporated.
1
2
3
4
5
6
7
8
9
10
11
12
24
23
22
21
20
19
18
17
16
15
14
13
A1
A2
A3
A4
GND
GND
GND
GND
A5
A6
A7
A8
DIR
B1
B2
B3
B4
VCC
VCC
B5
B6
B7
B8
OE
DB, DW, NT, OR PW PACKAGE
(TOP VIEW)
74ACT11245
OCTAL BUS TRANSCEIVER
WITH 3-STATE OUTPUTS
SCAS031C – JULY 1987 – REVISED APRIL 1996
2POST OFFICE BOX 655303 DALLAS, TEXAS 75265
logic symbol
This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12.
B8
B7
B6
B5
B4
B3
B2
B1
14
15
16
17
20
21
22
23
A8
A7
A6
A5
A4
A3
A2
A1
DIR
OE
12
11
10
9
4
3
2
1
24
13
2
1
3 EN2 [AB]
3 EN1 [BA]
G3
logic diagram (positive logic)
A8
A7
A6
A5
A4
A3
A2
A1
DIR
B8
B7
B6
B5
B4
B3
B2
B1
OE
14
15
16
17
20
21
22
23
13
12
11
10
9
4
3
2
1
24
74ACT11245
OCTAL BUS TRANSCEIVER
WITH 3-STATE OUTPUTS
SCAS031C – JULY 1987 – REVISED APRIL 1996
3
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage range, VCC –0.5 V to 7 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, VI (see Note 1) –0.5 V to VCC + 0.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output voltage range, VO (see Note 1) –0.5 V to VCC + 0.5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input clamp current, IIK (VI < 0 or VI > VCC) ±20 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output clamp current, IOK (VO < 0 or VO > VCC) ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous output current, IO (VO = 0 to VCC) ±50 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous current through VCC or GND ±200 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum power dissipation at TA = 55°C (in still air) (see Note 2):DB package 0.65 W. . . . . . . . . . . . . . . . . .
DW package 1.7 W. . . . . . . . . . . . . . . . . .
NT package 1.3 W. . . . . . . . . . . . . . . . . . .
PW package 0.7 W. . . . . . . . . . . . . . . . . . .
Storage temperature range, Tstg –65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only , and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may af fect device reliability.
NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. The maximum package power dissipation is calculated using a junction temperature of 150
_
C and a board trace length of 750 mils,
except for the NT package, which has a trace length of zero.
recommended operating conditions
MIN MAX UNIT
VCC Supply voltage 4.5 5.5 V
VIH High-level input voltage 2 V
VIL Low-level input voltage 0.8 V
VIInput voltage 0 VCC V
VOOutput voltage 0 VCC V
IOH High-level output current –24 mA
IOL Low-level output current 24 mA
D
t/
D
vInput transition rise or fall rate 0 10 ns/V
TAOperating free-air temperature –40 85 °C
74ACT11245
OCTAL BUS TRANSCEIVER
WITH 3-STATE OUTPUTS
SCAS031C – JULY 1987 – REVISED APRIL 1996
4POST OFFICE BOX 655303 DALLAS, TEXAS 75265
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
VCC
TA = 25°C
MIN
MAX
UNIT
PARAMETER
TEST
CONDITIONS
V
CC MIN TYP MAX
MIN
MAX
UNIT
IOH =50
m
A
4.5 V 4.4 4.4
I
OH = –
50
m
A
5.5 V 5.4 5.4
VOH
IOH =24mA
4.5 V 3.94 3.8 V
OH
I
OH = –
24
mA
5.5 V 4.94 4.8
IOH = –75 mA
{
5.5 V 3.85
IOL =50
m
A
4.5 V 0.1 0.1
I
OL =
50
m
A
5.5 V 0.1 0.1
VOL
IOL =24mA
4.5 V 0.36 0.44 V
OL
I
OL =
24
mA
5.5 V 0.36 0.44
IOL = 75 mA
{
5.5 V 1.65
IOZ A or B portsVO = VCC or GND 5.5 V ±0.5 ±5
m
A
IIOE or DIR VI = VCC or GND 5.5 V ±0.1 ±1
m
A
ICC VI = VCC or GND, IO = 0 5.5 V 8 80
m
A
D
ICC§One input at 3.4 V, Other inputs at GND or VCC 5.5 V 0.9 1 mA
CiVI = VCC or GND 5 V 4 pF
CoVO = VCC or GND 5 V 12 pF
Not more than one output should be tested at a time, and the duration of the test should not exceed 10 ms.
For I/O ports, the parameter IOZ includes the input leakage current.
§This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than 0 V or VCC.
switching characteristics over recomended ranges of supply voltage and operating free-air
temperature (unless otherwise noted) (see Figure 1)
PARAMETER
FROM TO TA = 25°C
MIN
MAX
UNIT
PARAMETER
(INPUT) (OUTPUT) MIN TYP MAX
MIN
MAX
UNIT
tPLH
AorB
BorA
1.5 6.2 9.2 1.5 10
ns
tPHL
A
or
B
B
or
A
1.5 5.4 8.6 1.5 9.1
ns
tPZH
OE
AorB
1.5 8.1 12 1.5 13.2
ns
tPZL
OE
A
or
B
1.5 8.2 11.7 1.5 12.9
ns
tPHZ
OE
AorB
1.5 9.3 11.8 1.5 12.9
ns
tPLZ
OE
A
or
B
1.5 9.8 12.9 1.5 13.9
ns
operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER TEST CONDITIONS TYP UNIT
Cd
Power dissi
p
ation ca
p
acitance
p
er transceiver
Outputs enabled
CL=50
p
F
f=1MHz
66 p
F
C
pd
Po
w
er
dissipation
capacitance
per
transcei
v
er
Outputs disabled
C
L =
50
pF
,
f
=
1
MH
z19
pF
74ACT11245
OCTAL BUS TRANSCEIVER
WITH 3-STATE OUTPUTS
SCAS031C – JULY 1987 – REVISED APRIL 1996
5
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PARAMETER MEASUREMENT INFORMATION
From Output
Under Test
CL = 50 pF
(see Note A)
LOAD CIRCUIT
S1
2 × VCC
500
500
tPLH tPHL
Output
Control
(low-level
enabling)
Output
Waveform 1
S1 at 2 × VCC
(see Note B)
Output
W aveform 2
S1 at GND
(see Note B)
VOL
VOH
tPZL
tPZH
tPLZ
tPHZ
1.5 V
1.5 V
1.5 V 1.5 V
[
VCC
3 V
0 V
50% VCC 50% VCC
VOH
VOL
0 V
50% VCC 20% VCC
50% VCC 80% VCC
[
0 V
3 V
GND
Open
Input
Output
VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
2 × VCC
GND
TEST S1
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
W aveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR 1 MHz, ZO = 50 , tr = 3 ns, tf = 3 ns.
D. The outputs are measured one at a time with one input transition per measurement.
Figure 1. Load Circuit and Voltage Waveforms
PACKAGING INFORMATION
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
74ACT11245DBLE OBSOLETE SSOP DB 24 TBD Call TI Call TI
74ACT11245DBR ACTIVE SSOP DB 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DBRE4 ACTIVE SSOP DB 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DBRG4 ACTIVE SSOP DB 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DW ACTIVE SOIC DW 24 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DWE4 ACTIVE SOIC DW 24 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DWG4 ACTIVE SOIC DW 24 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DWR ACTIVE SOIC DW 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DWRE4 ACTIVE SOIC DW 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DWRG4 ACTIVE SOIC DW 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245NSR ACTIVE SO NS 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245NSRE4 ACTIVE SO NS 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245NSRG4 ACTIVE SO NS 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245NT ACTIVE PDIP NT 24 15 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
74ACT11245NTE4 ACTIVE PDIP NT 24 15 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
74ACT11245PWLE OBSOLETE TSSOP PW 24 TBD Call TI Call TI
74ACT11245PWR ACTIVE TSSOP PW 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245PWRE4 ACTIVE TSSOP PW 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245PWRG4 ACTIVE TSSOP PW 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
PACKAGE OPTION ADDENDUM
www.ti.com 11-Nov-2009
Addendum-Page 1
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 11-Nov-2009
Addendum-Page 2
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0 (mm) B0 (mm) K0 (mm) P1
(mm) W
(mm) Pin1
Quadrant
74ACT11245DBR SSOP DB 24 2000 330.0 16.4 8.2 8.8 2.5 12.0 16.0 Q1
74ACT11245DWR SOIC DW 24 2000 330.0 24.4 10.75 15.7 2.7 12.0 24.0 Q1
74ACT11245NSR SO NS 24 2000 330.0 24.4 8.2 15.4 2.5 12.0 24.0 Q1
74ACT11245PWR TSSOP PW 24 2000 330.0 16.4 6.95 8.3 1.6 8.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 11-Mar-2008
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
74ACT11245DBR SSOP DB 24 2000 346.0 346.0 33.0
74ACT11245DWR SOIC DW 24 2000 346.0 346.0 41.0
74ACT11245NSR SO NS 24 2000 346.0 346.0 41.0
74ACT11245PWR TSSOP PW 24 2000 346.0 346.0 33.0
PACKAGE MATERIALS INFORMATION
www.ti.com 11-Mar-2008
Pack Materials-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE
4040065 /E 12/01
28 PINS SHOWN
Gage Plane
8,20
7,40
0,55
0,95
0,25
38
12,90
12,30
28
10,50
24
8,50
Seating Plane
9,907,90
30
10,50
9,90
0,38
5,60
5,00
15
0,22
14
A
28
1
2016
6,50
6,50
14
0,05 MIN
5,905,90
DIM
A MAX
A MIN
PINS **
2,00 MAX
6,90
7,50
0,65 M
0,15
0°ā8°
0,10
0,09
0,25
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,65 M
0,10
0,10
0,25
0,50
0,75
0,15 NOM
Gage Plane
28
9,80
9,60
24
7,90
7,70
2016
6,60
6,40
4040064/F 01/97
0,30
6,60
6,20
80,19
4,30
4,50
7
0,15
14
A
1
1,20 MAX
14
5,10
4,90
8
3,10
2,90
A MAX
A MIN
DIM PINS **
0,05
4,90
5,10
Seating Plane
0°–8°
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-153
PACKAGING INFORMATION
Orderable Device Status (1) Package
Type Package
Drawing Pins Package
Qty Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
74ACT11245DBLE OBSOLETE SSOP DB 24 TBD Call TI Call TI
74ACT11245DBR ACTIVE SSOP DB 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DBRE4 ACTIVE SSOP DB 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DBRG4 ACTIVE SSOP DB 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DW ACTIVE SOIC DW 24 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DWE4 ACTIVE SOIC DW 24 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DWG4 ACTIVE SOIC DW 24 25 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DWR ACTIVE SOIC DW 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DWRE4 ACTIVE SOIC DW 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245DWRG4 ACTIVE SOIC DW 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245NSR ACTIVE SO NS 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245NSRE4 ACTIVE SO NS 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245NSRG4 ACTIVE SO NS 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245NT ACTIVE PDIP NT 24 15 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
74ACT11245NTE4 ACTIVE PDIP NT 24 15 Pb-Free
(RoHS) CU NIPDAU N / A for Pkg Type
74ACT11245PWLE OBSOLETE TSSOP PW 24 TBD Call TI Call TI
74ACT11245PWR ACTIVE TSSOP PW 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245PWRE4 ACTIVE TSSOP PW 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
74ACT11245PWRG4 ACTIVE TSSOP PW 24 2000 Green (RoHS &
no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
PACKAGE OPTION ADDENDUM
www.ti.com 11-Nov-2009
Addendum-Page 1
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
PACKAGE OPTION ADDENDUM
www.ti.com 11-Nov-2009
Addendum-Page 2
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
74ACT11245DBR SSOP DB 24 2000 330.0 16.4 8.2 8.8 2.5 12.0 16.0 Q1
74ACT11245DWR SOIC DW 24 2000 330.0 24.4 10.75 15.7 2.7 12.0 24.0 Q1
74ACT11245NSR SO NS 24 2000 330.0 24.4 8.2 15.4 2.5 12.0 24.0 Q1
74ACT11245PWR TSSOP PW 24 2000 330.0 16.4 6.95 8.3 1.6 8.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
74ACT11245DBR SSOP DB 24 2000 367.0 367.0 38.0
74ACT11245DWR SOIC DW 24 2000 367.0 367.0 45.0
74ACT11245NSR SO NS 24 2000 367.0 367.0 45.0
74ACT11245PWR TSSOP PW 24 2000 367.0 367.0 38.0
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
DB (R-PDSO-G**) PLASTIC SMALL-OUTLINE
4040065 /E 12/01
28 PINS SHOWN
Gage Plane
8,20
7,40
0,55
0,95
0,25
38
12,90
12,30
28
10,50
24
8,50
Seating Plane
9,907,90
30
10,50
9,90
0,38
5,60
5,00
15
0,22
14
A
28
1
2016
6,50
6,50
14
0,05 MIN
5,905,90
DIM
A MAX
A MIN
PINS **
2,00 MAX
6,90
7,50
0,65 M
0,15
0°ā8°
0,10
0,09
0,25
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated