Digital Timer H5CN 1
Digital Timer
H5CN
Please read and understand this catalog before purchasing the prod-
ucts. Please consult your OMRON representative if your have any ques-
tions or comments. Refer to Warranty and Application Considerations
(page 16), and Safety Precautions (page 13).
Miniature DIN-sized (48 x 48 mm) Quartz
Timer with Abundant Series Versions
• Series version cover a wide range of rated times; 9.999 s,
99.99 s, 999.9 s, 99 min 59 s, and 99 hrs 59 min.
• Selection of elapsed ti me ind ic ation, remain ing tim e i ndication,
contact output, and solid-state output types to suit require-
ments.
• Power supply freely selectable within a range of 100 to
240 VAC, as well as 12 to 48 VDC.
• Models with a memory backup functi on aga ins t po wer fai lure
available.
Model Number Structure
■Model Number Legend
Note: This model number legend includes combinations that are not av ailable . Before ordering, please check the List of Models on page 2 for av ail-
ability.
1. Display
X:UP display (increments from 0 to the set time)
Y:DOWN display (decrements from the set time to 0)
2. Rated time
Z:0.001 to 9.999 s
A:0.001 to 99.99 s
B:0.1 to 999.9 s
C:1 s to 99 min 59 s
D:1 min to 99 h 59 min
3. Output mode
N: N mode (Power ON-d elay)
4. Backup power supply function for memory pro tec t ion
None:Not provided
M: Provided
5. Output type
None:Contact output (SPDT)
S: Solid-state output
21 3 4 5
H5CN- @@N@@
2Digital Timer H5CN
Ordering Information
■List of Mode ls
Note: 1. Specify both the model number and supply voltage when ordering.
2. The Y92S-20 Backup Battery (sold separately) provides power backup for memor y protection during power failures for approximately
5 y ears (at 20°C). Always connect a battery to the H5CN-X@NM. For details on connection methods, refer to page 5.
3. The H5CN-X@NM does not support power resetting.
■Accessories (Order Separately)
Display type UP display timer (increments f orm
0 to the set time) DOWN display timer (decre-
ments form the set time to 0) UP display timer (increments from 0
to the set time)
Output type Contact output (SPDT) Solid-state output
Pin type 11-pin 8-pin
Backup power supply function for
memory protection Uses external
battery (lithium).
(See notes 2 and
3.)
Not provided
Supply voltage 100 to 240 VAC 100 to 240 VAC, 12 to 48 VDC 12 to 48 VDC
Rated time 0.001 to 9.999 s --- --- --- H5CN-XZNS
0.001 to 99.99 s H5CN-XANM H5CN-XAN H5CN-YAN H5CN-XANS
0.1 to 999.9 s H5CN-XBNM H5CN-XBN H5CN-YBN ---
1 s to 99 min 59 s H5CN-XCNM H5CN-XCN H5CN-YCN ---
1 min to 99 h 59 min H5CN-XDNM H5CN-XDN H5CN-YDN ---
Su
pp
l
y
volta
g
e
Example: H5CN-XAN 12 to 48 VDC
Name Models
Flush Mounting Adapte r Y92F-30
Backup Battery Y92S-20
Tr ack Mountin g/Front
Connecting Socket 8-pin P2CF-08
11-pin P2CF-11
Back Connecting Socket 8-pin P3G-08
11-pin P3GA-11
Protective Cover Hard Cover Y92A-48B
Soft Cover Y92A-48D
Mounting Track 50 cm (I) ´ 7.3 mm (t) PFP-50N
1 m (I) ´ 7.3 mm (t) PFP-100N
1 m (I) ´ 16 mm (t) PFP-100N2
End Plate PFP-M
Spacer PFP-S
Digital Timer H5CN 3
Specifications
■Ratings
Note: Models with memory backup function are not avai lable for this range of DC supply vol tages.
■Characteristics
Note: 1. When timer operation is started by power application.
2. When timer operation is started after a reset input has been applied.
3. These values represent the total accuracy of the timer including the repeat accuracy, setting error, and variation due to volt a ge and tem-
perature changes. Note that they also comprise errors due to the rise time of the power source and the operating times of the internal
and output circuits.
Item Contact output Solid-state output
Rated supply voltage 100 to 240 V A C (50/60 Hz), 12 to 48 VDC (permissible rip-
ple: 20% max.) (see note) 12 to 48 VDC (permissible ripple: 20% max.)
Operating voltage range 85% to 110% of rated supply voltage
Power consumption Approx. 12 VA at 240 VAC, 50 Hz
Approx. 2.5 W at 48 VDC Approx. 2.5 W at 48 VDC
Mounti ng met hod Surface mounting or flush mounting
Display 7-segment LEDs (8-mm-high characters), UP indicator
Input method Contact open and shor t-circuit input Open-collector transistor ON/OFF input
Resetting system and
gate inp ut Reset by power-OFF (not provided for models with backup power for memory protection):
min. power OFF time: 0.5 s
External reset or gate (common to contact and solid-state inputs): min. reset input signal w idth: 0.02 s;
residual voltage: 2 V max.
Output mode N mode (Power ON-delay)
Control outputs SPDT: 3 A at 250 VAC, resistive load (cosf = 1) Open collector: 100 mA max. at 30 VDC max.
Ambient temperature Operating:–10°C t o 55°C (with no icing or condensation)
Storage:–25°C to 65°C (with no icing or condensation)
Ambient humidity Operating: 35% to 85%
Case color Light gray (Munsell 5Y7/1)
Accuracy of operating time ±0.01% ±0.05 s max. (see note 1), ±0.005% ±0.03 s max. (see note 2) (see note 3)
Setting error
Influenc e of volt a ge
Influence of temperature
Insulation resistance 100 MW min. (at 500 VDC) (between current-carrying terminal and exposed non-cur rent carrying
metal parts, between power supply circuit and control output circuit)
Dielectric strength 2,000 VAC , 50/ 60 Hz for 1 min (between current-carrying terminal and exposed non-current-carrying
metal parts, between power supply circuit and control output circuit)
Impulse withstand voltage 6 kV (between power supply ter minal)
6 kV (between current-carrying terminal and exposed non-current carrying metal parts)
Noise immunity Square-wave noise by noise simulator
AC: ±2 kV (between power supply terminals)
DC: ±480 V (between power supply terminals), ±500 V (between input terminals)
Static immunity Malfunction: 8 kV
Vibration resistance Destruction:10 to 55 Hz with 0.75-mm single amplitude each in 3 directions for 2 ho urs each
Malfunction:10 to 55 Hz with 0.5-mm single amplitude each in 3 directions for 10 minutes each
Shock resistance Destruction:300 m/s2 3 times each in 6 directions
Malfunction:100 m/s2 3 times each in 6 directions
Life expec tancy Mechanical:10,000,000 operations min.
Electrical:100,000 operations min. (3 A at 250 VAC, resistive load)
Approved standards UL508, CSA C22.2 No . 14
Weight Approx. 200 g
4Digital Timer H5CN
■Life-test Curve (Reference Values)
A maximum current of 0.15A can be switched at 125 VDC (cosf = 1)
Maximum current of 0.1 A can be switched if L/R is 7 ms. In both
cases, a life of 100,000 operations can be expected. The minimum
applicable load is 10 mA at 5 VDC (failure level: P reference value).
Load current (A)
1,000
700
500
300
100
70
50
30
10
501234
7
30 VDC cosφ =1
250 VAC cosφ =1
30 VDC L/R = 7 ms
250 VAC cosφ =0.4
Number of switching operations (×104 times)
Digital Timer H5CN 5
Connections
■Block Diagram
H5CN-@@N (without Backup Power for Memory Protection)
Using an AC Power Supply (Contact Outputs)
Using a DC Power Supply (Solid-state Outputs)
Note: The following block diagram shows the differences for the equivalent section indicated by “a” in the above block diagram.
Thumbwheel
switch One-shot timer
circuit
Initial clear
circuit
Quartz-
crystal
oscillator
Microcomputer-
type custom LSI
Filter Filter
Timer circuit
Filter
Reset input Gate input
Clock 7-segment
indicator
Output
circuit
UP display
Constant-
voltage
circuit
Rectifier
circuit
Note: 1. If the reset input is short-circuited (be-
tween terminals A and C), immediately
the count circuit is reset to 0 and the con-
trol output relay is reset to OFF. The tim-
er starts as soon as the reset input is
opened (between terminals A and C).
2. If the gate input is short-circuited (be-
tween terminals A and D), the count cir-
cuit stops immediately. The timer then
restarts as soon as the gate input is
opened (between terminals A and D).
Filter
Constant-
voltage
circuit
Power
supply
circuit
Filter Filter
Reset input Gate input
Note: Terminals A and B are internally short-circuited.
6Digital Timer H5CN
H5CN-X@NM (with Backup Power for Memory Protection)
Note: Be sure to install a Backup Battery (sold separately).
Thumbwheel
switch One-shot timer
circuit
Clock 7-segment
indicator
Output
circuit
Timer circuit
Filter Filter
Gate input Reset input
Power failure
detection
circuit
Quartz-
crystal
oscillator
Filter
Microcomputer-
type custom LSI
Constant-
voltage
circuit
Rectifier
circuit
External
battery
UP indicator lit
Note: 1. If the reset input is short-circuited (be-
tween terminals C and G), immediately
the count circuit is initialized and the con-
trol output relay is reset to OFF. The timer
starts as soon as the reset input is opened
(between terminals C and G).
2. If the gate input is short-circuited (be-
tween terminals C and E), the count cir-
cuit stops immediately. The timer then
restarts as soon as the gate input is
opened (between terminals C and E).
Digital Timer H5CN 7
Installation
■Connections
1. Battery Connection (H5CN-X@NM
Only)
Model with Backup
Power for Memory
Protection
Connect the Y92S-20 Backup Bat-
tery between terminals A and D,
making sure the polarities are cor-
rect.
2. Power Supply Connection
Model without Backup Power for Memor y
Protection
Connect the timer so that the required supply voltage ca n be applied
across terminals B and G. (Make sure that the polarity of the DC
power supply is correct.)
Model with Backup Power for Memory
Pr otection (H5CN-X@NM)
Connect the timer so that the required supply voltage ca n be applied
across terminals B and J.
3. Connection of Load Circuit (Control
Output)
Model without Backup Power for Memor y
Protection
Contact Output Type
Internal Circuit of Control Output
Contacts
Terminals E, F, and H are for con-
trol output contacts.
Connecting of Load Circuit
Load 1 connected in series with NO contact (between terminals F
and H) is normally open, and the load circuit voltage will be applied
after the lapse of the set time. The load circuit voltage is normally
applied to load 2 conne cted in series with NC contact (between ter-
minals E and H), which will be open after the lapse of the set time.
Note: The maximum load current is 3 A (resistive load).
Solid-state Output Type
Internal Circuit of Control Output
Terminals F and H are an open collector output. A diode is inter-
nally connected between terminals E and F to absorb counterelec-
tromotive force that occurs when an inductive load is connected.
Connection of Load Circuit
Voltage is applied to the load after the set time has lapsed.
Note: The maximum load current is 100 mA.
Model with Backup Power for Memory
Protection (H5CN-X@NM)
Contact Output Type
Internal Circuit of Control Output Contac ts
Terminal H, I, and K are for control output contacts.
External
battery 3 V
AC Power Supply
100 to 240 VAC
DC Power Supply
12 to 48 VDC
External
battery
100 to 240 VAC
Load circuit voltage
(250 V A C, 30 VDC max.)
Load 2
Load 1
Load
Load voltage
(30 VDC max.)
External
battery
8Digital Timer H5CN
Connecti on of Loa d Circuit
Load 1 connected in series with NO contact (between terminals I
and K) is normally open, and the load circ uit voltage will be applied
to it after the lapse of the set time . The load circuit v oltage i s normally
applied to load 2 connec ted in ser ies with NC contact (between ter-
minals H and K), which will be open after the lapse of the set time.
4. Connection of Reset Input
Connection of the reset input contact or an open collector transistor
between terminals A and C (between terminals C and G for mod-
els with backup power for memory protection) permits the timer to
reset when contact is made or the transistor turns ON. Use of a high-
reliability gold-plated contact is recommended for the reset input. For
the reset input transistor, select the one satisfying the following elec-
trical ratings:
VCEO = 20 V min.
IC = 50 mA min.
ICEO (leakage current) = 0.5 mA max.
VCE(sat) (residual voltage) = 2 V max.
Model without Backup Power for Memory
Protection
Model wi th Backup Power for Memory
Protection (H5CN-X@NM)
5. Connection of Gate Input
Connection of the gate input contact or an open collector transistor
between terminals A and D (between ter minals C and E for mod-
els with backup power for memory protection) permits the timer to
stop operation while contact is mad e or the transistor tur ns O N. Use
of a high-reliability gold-plated contact is recommended for the gate
input. For the gate input transistor, select the one satisfying the fol-
lowing electrical ratings:
VCEO = 20 V min.
IC = 50 mA min.
ICEO (leakage current) = 0.1 mA max.
VCE(sat) (residual voltage) = 2 V max.
Use a gate input contact with a shor t bounce time because the con-
tact bounce time causes an error in the operate time of the timer for a
period equalling the bounce time.
Model without Backup Power for Memory
Protection
Model with Backup Power for Memory
Protection (H5CN-X@NM)
6. Battery Connections when Using
Backup Power for Memory Protection
Always con nect a batter y when using m odels with backup power for
memory protection (H5CN-X@NM). Any 3-V battery can be used, but
the backup time will depend on the capacity of the batter y.
When using the Unit for the first time after purchase, apply power
and reset the Unit once before using it. When pow er is turned ON for
the first time, outputs may be produced at the same time, so do not
connect the output terminals.
When connecting the battery using a Socket (P2CF-11 or P3GA-11),
check the terminal numbers on the Socket and connect the positive
side of the battery to terminal D and the negative side to terminal A.
Note: The maximum load current is 3 A (resistive load).
Load circuit
voltage
(250 V A C,
30 VDC max.)
Load 2
Load 1
External
battery
Reset input
transistor
(Timer resets
when transistor
is ON.)
Reset input
contact
(Timer resets
when contact is
made.)
Reset input
transistor
(Timer resets
when transistor
is ON.)
Reset input
contact
(Timer resets
when contact is
made.)
External
battery
External
battery
Gate input contact
(Timer stops when
contact is made.)
Gate input transistor
(Timer stops when
transistor is ON.)
Gate input transistor
(Timer stops when
transistor is ON.)
Gate input contact
(Timer stops when
contact is made.)
External
battery
External
battery
Digital Timer H5CN 9
Operation
■Timing Chart
Digital Display
UP Display DOWN Display
Reset input
Gate input
Time up
Setting value
0
Control output
Power supply
Time up indication
Digital display
Reset input
Gate input
Time up
Setting value
0
Control output
Time up indication
Digital display
Power supply
No digital
display
No digital
display
Power ON Power ON
10 Digital Timer H5CN
Dimensions
Note: All units are in millimeters unless otherwise indicated.
■Dimensions without Flush Mounting Adapt er
■Dimensions with Flush Mounting Adapter
■Dimensions with Front Connecting Socket
Note: These dimensions vary with the kind of DIN track (reference value).
H5CN-X@N/-Y@N/-X@NS (Flush Mounting/Surface Mounting Models)
H5CN-X@NM (Flush Mounting/Surface Mounting Models)
44.8 × 44.8
44.8 × 44.8
▲
▲
8 pins
11 pins
Panel Y92F-30 (order separately)
Flush Mounting Adapter
H5CN-X@N/-Y@N/-X@NS (Adapter Ordered Separately)
H5CN-X@NM (Adapter Ordered Separately)
P3GA-11 (order separately)
Back Connecting Socket
Panel Y92F-30 (order separately)
Flush Mounting Adapter
95.1
P3G-08 (order separately)
Back Connecting Socket
Panel Cutout
Note: 1. Panel thickness: 1 to 5 mm
3. No cover:
N = (48n − 2.5) +1/−0
With hard cover:
N = {48n − 2.5 + (n − 1) x 3} +1/−0
N
2. When gang-mounting the Unit, the
orientation of the Adapter must be
changed depending on whether
Units are mounted horizontally or
vertically.
45 +0.6
−0
45 +0.6
−0
45 +0.6
−0
The standard panel cutout is as below.
(Panel cutout conforms to DIN 43700.)
Gang-mounting of more than 2 units
(horizontally)
H5CN
-X@N,Y@N,
X@NS
H5CN
-X@NM
P2CF-08 P2CF-11
Digital Timer H5CN 11
■Accessories (Order Separately)
Note: All units are in millimeters unless otherwise indicated.
20.3 max.
7.8 34.5
35.4
4
40±0.2
70 max.
50 max. 20.3 max.
Track Mounting/Front Connecting Socket
P2CF-08
Surface Mounting Hole
s
Two, 4.5 dia. or two, M4
Terminal Arrangement/
Internal Connections
(T op View)
Eight,
M3.5 x 7.5 sems
Two, 4.5 dia.
holes
40±0.2
7.8 34.5
35.4
4
Track Mounting/Front Connecting Socket
P2CF-11 Surface Mounting Hole
s
Two, 4.5 dia. or two, M4
70 max.
50 max. 31.2 max.
Terminal Arrangement/
Internal Connections
(T op View)
Eleven,
M3.5 x 7.5 sems
Two, 4.5 dia.
holes
45
45 4.9 17
45
45
25.6
4.5 16.3 6.2
27 dia.
Back Connecting Socket
P3G-08
P3GA-11 27 dia.
Terminal Arrangement/
Internal Connections
(Bottom View)
Terminal Arrangement/
Internal Connections
(Bottom View)
12 Digital Timer H5CN
Y92F-30
Flush Mounting Adapter
Y92S-20
Backup Battery
Y92A-48D (See note 1.)
Soft Cover Y92A-48B (See note 2.)
Hard Cover
Note: 1. The soft protective cover allows the set value to be set by
depressing the thumbwheel switches through it. It may be,
however, difficult to make setting changes of the Timer
with the Y92A-48D Protective Cover attached, which must
be taken into consideration before using the Y92A-48D
Protective Cover.
2. The hard protective cover prevents the set value from be-
ing altered due to accidental contact with the push type
thumbwheel switch.
4.5 dia. hole
22.5 dia. Red lead wire (0.18 × 12 conductors)
L=120 mm
Note: Always connect a battery to models with
backup power for memory protection
(H5CN-@M).
4.5
15 25 25 25 25 *
10 10
7.3±0.15
35±0.3 27±0.15
1
4.5
15 25 25 25 25 15
10 10
1,000
27 24
16
29.2
11.5
50
11.5
10
6.2 1.8
135.5 35.3
1.8
1.3
4.8
516
12
44.3
16.5
10
34.8
35±0.3
Mounting T rack
PFP-100N, PFP-50N PFP-100N2
End Plate
PFP-M Spacer
PFP-S
1,000 (500)
(See note.)
Note: The values shown in parentheses are for the PFP-50N.
M4 x 8
pan head
screw
Digital Timer H5CN 13
Safety Precautions
■Precautions for Correct Use
Battery Connections when Using
Backup Power for Memory Protection
Always connect a battery when using models with backup power for
memory protection. Any 3-V battery can be used, but the backup
time will depend on the capacity of the battery. When using the Unit
for the first time after purchase, apply pow er and reset the Unit once
before using it. When power is turned ON for the first time, outputs
may be produced at the same time, so do not connect the output
terminals.
If a power interruption contin ues for 10 minut es or more when a
battery is not connected, the count value and displays may be
meaningless, and outputs may be produced unpredictably ev en if the
power supply recov ers. If this happens, apply power to the reset input
once before using the Unit further. (The Unit can be used after
turning ON the reset input, regardless of whether a battery is
connected or not.)
Regular battery replacem ent (every 4 to 5 years) is recommended.
The lif e of the battery depends on the frequency of power f ailures.
Connection Methods
Setting of Operating Time
Time Setting Range
1. The H5CN Timer is capable of reading the input data at any time
during norm al operation. This means that the set time can be
changed during power application. This feature sets back the
output from the timer by temporarily setting the longer time or
quickens the output by setting the shorter time. During norm al
operation, the set time may be accidentally changed by touching
a thumbwheel switch. To prevent this possibility, use the optional
Y92A-48@ Protective Cover.
2. When the set time is all zeroes (e.g., 000.0 s or 00 h 00 min),
there will be a momentary control output upon power application,
which can be used to check normal output. When changing the
set time during normal operation, pa y special attention not to alter
the set value to this all zeroes.
3. When changing the set time while power is being supplied, an
inadequate push of the thumbwheel switches will display two
numbers in one digital display window, causing the operating time
to drift widely. Therefore, press the thumb-wheel switches surely.
Take particular care when the other three digits are all zeroes,
because the improper setting of the fourt h switch to create four
zeroes will cause an instantaneous output.
Undesi rable S etti ng
4. Take particular care with the H5CN-@Z@, which is capable of
setting in 1/1000th of a second because there is an error of
between 0.03 to 0.05 ms. (Repeat accuracy is 1 to 2 ms.)
Operation Examples
•During Incremental Operation
If the set value is changed to a value higher than the currently
displayed present value, the timer will time out for the new set
value.
•During Decremental Operation
When the set value changes, the difference between the new set
v alue and old set value will be added or subtracted from the
present value.
Example:
The Y92S-20 Backup Battery used for the H5CN-X@NM is a lithium
battery (non-explosion-proof). Do not short-circuit the positive and
negative sides of the battery, recharge or disassemble the battery,
deform the battery under pressure, or dispose of the battery in fire.
Doing so may occasionally cause the battery to burst, ignite, or leak.
Use only the specified battery. Otherwise, the battery may leak or
burst, occasionally causing damage to the equipment or minor injury.
!WARNING
Y92S-20 or
equivalent 3-V battery
To terminal No. 4
To terminal No. 1
Y92S-20
P2CF-11
To terminal No. 1
Y92S-20
P3GA-11
To terminal No. 4
Setti ng r a nge Models
0.001 to 9.999 s H5CN-@Z@
0.01 to 99.99 s H5CN-@A@
0.1 to 999.9 s H5CN-@B@
1 s to 99 min 59 s H5CN-@C@
1 min to 99 h 59 min H5CN-@D@
Old set value New set value
200 s -> 100 s
Present value
(before changing setting) Present set value
(after changing setting)
160 s -> 60 s
min sec
5 min 30 s
hours min
00h00min
(Instant output)
Changing unwanted
settings
Conceivable
operating time
14 Digital Timer H5CN
Power Supply
Leave the power supply OFF for at least 0.5 s before turning it back
ON (power supply reset).
Inputs and Outputs
•Do not apply voltage externally to input terminals A, C, and D.
•When using contacts for the rese t input and gate input, use gold-
plated contacts with good contact reliability. Use gate input
contacts with short contact bounce (chattering).
Operation during Power Failures
•When Units without backup power f or memory protection are used,
the timer status during momentary power f ailures is as shown i n the
following diagrams.
A. Power Failure of 0.01 s Max.
B. Power Failure of 0.5 s Min.
C. Power Failure of 0.01 to 0.5 s Max.
•Units with backup power f or memory protection will restart from the
status before the power failure as shown in example A, regardless
of the length of time of the power failure.
Power failure
*Restarts from status before power failure.
m m+1 m+2
m−1m−2
*Restarts from initial status after power reset.
m 123m−1m−2
Power failure
*Either A or B are undefined.
m 123
m m+1 m+2
m−1m−2
Power failure
16
In the interest of product improv eme nt, sp eci fica tions are subject to change witho ut notic e.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03 937. To convert grams into ounces, multiply by 0.03527.
Cat. No. L052-E1-10
OMRON Corporation
Industrial Automation Company
Industrial Devices and Components Division H.Q.
Industrial Control Components Department
Shiokoji Horikawa, Shimogyo-ku,
Kyoto, 600-8530 Japan
Tel: (81)75-344-7119/Fax: (81)75-344-7149 Printed in Japan
1203-0.5C (0696) (M)
Warranty and Application Cons iderations
Warranty and Limitations of Liability
WARRANTY
OMRON's exclusiv e warranty is that the products are free from def ects in materials and workmanship for a period of one year (or
other period if specified) from date of sale by OMRON.
OMRON MAKES NO W ARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT,
MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR US ER
ACKNO WLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET
THE REQUIREMENTS OF THEIR INTENDE D USE. OMRON DI SCLAIMS ALL OTHE R WARRANTIE S, EXPRESS OR
IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS,
OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON
CONTRAC T, WARRANTY, NEGLIGEN CE , OR ST RICT LIAB IL IT Y.
In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE
PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED,
INSTALLED, AND M AINTAINED AN D NOT SUBJECT TO CONTAMI NATI O N, ABUSE, MI SUSE, OR IN APPROPRIATE
MODI FICATION OR REPAIR.
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for con formi ty with any standards, codes, or regula tions that apply to the combination of
products in the cust omer's applicatio n or use of the produ cts.
Ta ke all necessary steps to det ermine the suit ability of the product for the systems, machines, and equipment wi th w hich it will
be used.
Know and observe all prohibitions of use applicable to this produ ct.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIO US RISK TO L IFE OR PROPERTY WITHOUT
ENSURING THAT THE SYSTEM AS A W H OLE HAS B E EN DESIGNED TO AD DRESS TH E RISKS , AND THAT THE OMRON
PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE O VERALL EQUIPMENT OR
SYSTEM.
Disclaimers
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons. Consult with
your OMRON representative at any time to confirm actual specifications of purchased product.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
