LP2998 www.ti.com SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 LP2998 DDR-I and DDR-II Termination Regulator Check for Samples: LP2998 FEATURES DESCRIPTION * * * * * * * * The LP2998 linear regulator is designed to meet JEDEC SSTL-2 and JEDEC SSTL-18 specifications for termination of DDR1-SDRAM and DDR-II memory. The device contains a high-speed operational amplifier to provide excellent response to load transients. The output stage prevents shoot through while delivering 1.5A continuous current as required for DDR1-SDRAM termination, and 0.5A continuous current as required for DDR-II termination. The LP2998 also incorporates a VSENSE pin to provide superior load regulation and a VREF output as a reference for the chipset and DIMMs. 1 2 Source and Sink Current Low Output Voltage Offset No External Resistors Required Linear Topology Suspend to Ram (STR) Functionality Low External Component Count Thermal Shutdown Available in SOIC-8, SO PowerPAD-8 Packages APPLICATIONS * * * * An additional feature found on the LP2998 is an active low shutdown (SD) pin that provides Suspend To RAM (STR) functionality. When SD is pulled low, the VTT output will tri-state providing a high impedance output, while VREF remains active. A power savings advantage can be obtained in this mode through lower quiescent current. DDR-I, DDR-II and DDR-III Termination Voltage SSTL-18 Termination SSTL-2 and SSTL-3 Termination HSTL Termination Typical Application Circuit LP2998 AVIN = 2.5V AVIN VDDQ = 1.8V VDDQ + CIN CREF VSENSE PVIN + VREF = 0.9V VREF SD SD VTT = 0.9V VTT GND + COUT 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2007-2013, Texas Instruments Incorporated LP2998 SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 www.ti.com Connection Diagrams Top View GND 1 8 VTT SD VSENSE 2 7 PVIN 3 6 VREF 4 5 AVIN VDDQ GND Figure 1. SO PowerPAD-8 Package See Package Number DDA0008A Top View GND 1 8 VTT SD VSENSE 2 7 PVIN 3 6 VREF 4 5 AVIN VDDQ Figure 2. SOIC-8 Package See Package Number D0008A Pin Descriptions SOIC-8 Pin or SO PowerPAD-8 Pin Name Function 1 GND 2 SD 3 VSENSE 4 VREF Buffered internal reference voltage of VDDQ /2. 5 VDDQ Input for internal reference equal to VDDQ/2. 6 AVIN Analog input pin. 7 PVIN Power input pin. 8 VTT Output voltage for connection to termination resistors. EP Exposed pad thermal connection. Connect to Ground (SO PowerPAD-8 only). Ground. Shutdown. Feedback pin for regulating VTT. These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 LP2998 www.ti.com SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 Absolute Maximum Ratings (1) (2) AVIN to GND -0.3V to +6V PVIN to GND -0.3V to AVIN VDDQ (3) -0.3V to +6V Storage Temp. Range -65C to +150C Junction Temperature 150C Lead Temperature (Soldering, 10 sec) 260C SOIC-8 Thermal Resistance (JA) 151C/W SO PowerPAD-8 Thermal Resistance (JA) Minimum ESD Rating (1) (2) (3) (4) 43C/W (4) 1kV Absolute maximum ratings indicate limits beyond which damage to the device may occur. Operating range indicates conditions for which the device is intended to be functional, but does not ensure specific performance limits. For ensured specifications and test conditions see Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. VDDQ voltage must be less than 2 x (AVIN - 1) or 6V, whichever is smaller. The human body model is a 100 pF capacitor discharged through a 1.5 k resistor into each pin. Operating Range Junction Temp. Range (1) -40C to +125C AVIN to GND (1) 2.2V to 5.5V At elevated temperatures, devices must be derated based on thermal resistance. The device in the SOIC-8 package must be derated at JA = 151.2 C/W junction to ambient with no heat sink. Electrical Characteristics Specifications with standard typeface are for TJ = 25C and limits in boldface type apply over the full Operating Temperature Range (TJ = -40C to +125C) (1). Unless otherwise specified, VIN = AVIN = PVIN = 2.5V. Parameter VREF Voltage (DDR I) VREF Voltage (DDR II) VREF VREF Voltage (DDR III) ZVREF (1) VREF Output Impedance Min Typ Max Units VIN = VDDQ = 2.3V Test Conditions 1.135 1.158 1.185 V VIN = VDDQ = 2.5V 1.235 1.258 1.285 V VIN = VDDQ = 2.7V 1.335 1.358 1.385 V PVIN = VDDQ = 1.7V 0.837 0.860 0.887 V PVIN = VDDQ = 1.8V 0.887 0.910 0.937 V PVIN = VDDQ = 1.9V 0.936 0.959 0.986 V PVIN = VDDQ = 1.35V 0.669 0.684 0.699 V PVIN = VDDQ = 1.5V 0.743 0.758 0.773 V PVIN = VDDQ = 1.6V 0.793 0.808 0.823 IREF = -30 to +30 A 2.5 V k Limits are 100% production tested at 25C. Limits over the operating temperature range are specified through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate Average Outgoing Quality Level (AOQL). Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 3 LP2998 SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 www.ti.com Electrical Characteristics (continued) Specifications with standard typeface are for TJ = 25C and limits in boldface type apply over the full Operating Temperature Range (TJ = -40C to +125C) (1). Unless otherwise specified, VIN = AVIN = PVIN = 2.5V. Parameter Test Conditions Min Typ Max Units VIN = VDDQ = 2.3V 1.120 1.159 1.190 V VIN = VDDQ = 2.5V 1.210 1.259 1.290 V VIN = VDDQ = 2.7V 1.320 1.359 1.390 V VIN = VDDQ = 2.3V 1.125 1.159 1.190 V VIN = VDDQ = 2.5V 1.225 1.259 1.290 V VIN = VDDQ = 2.7V 1.325 1.359 1.390 V PVIN = VDDQ = 1.7V 0.822 0.856 0.887 V PVIN = VDDQ = 1.8V 0.874 0.908 0.939 V PVIN = VDDQ = 1.9V 0.923 0.957 0.988 V PVIN = VDDQ = 1.7V 0.820 0.856 0.890 V PVIN = VDDQ = 1.8V 0.870 0.908 0.940 V PVIN = VDDQ = 1.9V 0.920 0.957 0.990 V PVIN = VDDQ = 1.35V 0.656 0.677 0.698 V PVIN = VDDQ = 1.5V 0.731 0.752 0.773 V PVIN = VDDQ = 1.6V 0.781 0.802 0.823 V IOUT = +0.2A, AVIN = 2.5V PVIN = VDDQ = 1.35V 0.667 0.688 0.710 V IOUT = -0.2A, AVIN = 2.5V PVIN = VDDQ = 1.35V 0.641 0.673 0.694 V IOUT = +0.4A, AVIN = 2.5V PVIN = VDDQ = 1.5V 0.740 0.763 0.786 V IOUT = -0.4A, AVIN = 2.5V PVIN = VDDQ = 1.5V 0.731 0.752 0.773 V IOUT = +0.5A, AVIN = 2.5V PVIN = VDDQ = 1.6V 0.790 0.813 0.836 V IOUT = -0.5A, AVIN = 2.5V PVIN = VDDQ = 1.6V 0.781 0.802 0.823 V IOUT = 0A -30 0 30 mV IOUT = -1.5A -30 0 30 mV IOUT = +1.5A -30 0 30 mV IOUT = 0A -30 0 30 mV IOUT = -0.5A -30 0 30 mV IOUT = +0.5A -30 0 30 mV IOUT = 0A -30 0 30 mV IOUT = 0.2A -30 0 30 mV IOUT = 0.4A -30 0 30 mV IOUT = 0.5A -30 0 30 mV 320 500 IOUT = 0A VTT Output Voltage (DDR I) (2) IOUT = +/- 1.5A IOUT = 0A, AVIN = 2.5V VTT Output Voltage (DDR II) (2) IOUT = +/- 0.5A, AVIN = 2.5V VTT IOUT = 0A, AVIN = 2.5V VTT Output Voltage (DDR III) (2) VTT Output Voltage Offset (VREF - VTT) for DDR I (3) VTT Output Voltage Offset (VREF - VTT) for DDR II (3) VOSVtt VTT Output Voltage Offset (VREF - VTT) for DDR III IQ ZVDDQ ISD (2) (3) (4) 4 Quiescent Current (4) (3) IOUT = 0A VDDQ Input Impedance Quiescent current in shutdown 100 (4) SD = 0V 115 A k 150 A VTT load regulation is tested by using a 10 ms current pulse and measuring VTT. VTT load regulation is tested by using a 10 ms current pulse and measuring VTT. Quiescent current is defined as the current flow into AVIN. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 LP2998 www.ti.com SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 Electrical Characteristics (continued) Specifications with standard typeface are for TJ = 25C and limits in boldface type apply over the full Operating Temperature Range (TJ = -40C to +125C) (1). Unless otherwise specified, VIN = AVIN = PVIN = 2.5V. Parameter IQ_SD Shutdown leakage current VIH Minimum Shutdown High Level VIL Maximum Shutdown Low Level Iv VTT leakage current in shutdown ISENSE TSD Test Conditions SD = 0V VTT = 1.25V (5) TSD_HYS Thermal Shutdown Hysteresis (5) Typ Max Units 2 5 A 1.9 VSENSE Input current Thermal Shutdown Min SD = 0V V 1 0.8 V 10 A 13 nA 165 C 10 C The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction to ambient thermal resistance, JA, and the ambient temperature, TA. Exceeding the maximum allowable power dissipation will cause excessive die temperature and the regulator will go into thermal shutdown. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 5 LP2998 SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics Unless otherwise specified VIN = AVIN = PVIN = 2.5V Iq vs AVIN 1050 350 900 300 750 250 600 IQ (uA) IQ (uA) Iq vs AVIN in SD 400 200 450 150 300 100 150 50 0 2 2.5 3 3.5 4 4.5 5 5.5 2 2.5 3 3.5 AVIN (V) 4 4.5 5 5.5 AVIN (V) Figure 3. Figure 4. VIH and VIL VREF vs VDDQ 4 3 3.5 2.5 3 VREF (V) VSD (V) 2 2.5 2 1.5 1 1.5 0.5 1 0.5 0 2 2.5 3 3.5 4 4.5 5 5.5 0 1 2 AVIN (V) 4 5 6 VDDQ (V) Figure 5. Figure 6. VTT vs VDDQ ISD vs AVIN over Temperature 3 400 2.5 350 -40C 300 ISD (PA) 2 VTT (V) 3 1.5 250 25C 85C 200 125C 1 150 0.5 100 0 50 0 1 2 3 4 5 6 2.5 3 3.5 4 4.5 5 5.5 AVIN (V) VDDQ (V) Figure 7. 6 2 Figure 8. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 LP2998 www.ti.com SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 Typical Performance Characteristics (continued) Unless otherwise specified VIN = AVIN = PVIN = 2.5V Maximum Sourcing Current vs AVIN (VDDQ = 1.8V, PVIN = 1.8V) Iq vs AVIN over Temperature 1.4 1050 25oC IQ (PA) 750 1.2 OUTPUT CURRENT (A) 900 -40oC 600 85oC o 125 C 450 300 1 0.8 0.6 0.4 0.2 150 0 2 0 2.5 3 3.5 4 4.5 5 5.5 2 2.5 3 3.5 4 4.5 5 5.5 AVIN (V) Figure 9. Figure 10. Maximum Sinking Current vs AVIN (VDDQ = 1.8V) Maximum Sourcing Current vs AVIN (VDDQ = 2.5V, PVIN = 1.8V) 2.4 1.4 2.2 1.2 2 1 OUTPUT CURRENT (A) OUTPUT CURRENT (A) AVIN (V) 1.8 1.6 1.4 1.2 0.8 0.6 0.4 0.2 1 0 2 2.5 3 3.5 4 4.5 5 5.5 2 2.5 3 AVIN (V) 3.5 4 4.5 5 5.5 AVIN (V) Figure 11. Figure 12. Maximum Sourcing Current vs AVIN (VDDQ = 2.5V, PVIN = 2.5V) Maximum Sourcing Current vs AVIN (VDDQ = 2.5V, PVIN = 3.3V) 1.8 3 1.7 OUTPUT CURRENT (A) OUTPUT CURRENT (A) 2.8 1.6 1.5 1.4 1.3 2.6 2.4 2.2 1.2 1.1 2 2 2.5 3 3.5 4 4.5 5 5.5 AVIN (V) 3 3.5 4 4.5 5 5.5 AVIN (V) Figure 13. Figure 14. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 7 LP2998 SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) Unless otherwise specified VIN = AVIN = PVIN = 2.5V Maximum Sinking Current vs AVIN (VDDQ = 2.5V) Maximum Sourcing Current vs AVIN (VDDQ = 1.8V, PVIN = 3.3V) 3.0 3 2.8 OUTPUT CURRENT (A) OUTPUT CURRENT (A) 2.8 2.6 2.4 2.2 2.0 2.6 2.4 2.2 1.8 1.6 2 2 2.5 3 3.5 4 4.5 5 5.5 AVIN (V) 3.5 4 4.5 5 5.5 AVIN (V) Figure 15. 8 3 Figure 16. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 LP2998 www.ti.com SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 Block Diagram VDDQ SD PVIN AVIN 50k VREF + - + 50k VTT VSENSE GND DETAILED DESCRIPTION The LP2998 is a linear bus termination regulator designed to meet the JEDEC requirements of SSTL-2 and SSTL-18. The output, VTT is capable of sinking and sourcing current while regulating the output voltage equal to VDDQ / 2. The output stage has been designed to maintain excellent load regulation while preventing shoot through. The LP2998 also incorporates two distinct power rails that separates the analog circuitry from the power output stage. This allows a split rail approach to be utilized to decrease internal power dissipation. It also permits the LP2998 to provide a termination solution for the next generation of DDR-SDRAM memory (DDRII). The LP2998 can also be used to provide a termination voltage for other logic schemes such as SSTL-3 or HSTL. Series Stub Termination Logic (SSTL) was created to improve signal integrity of the data transmission across the memory bus. This termination scheme is essential to prevent data error from signal reflections while transmitting at high frequencies encountered with DDR-SDRAM. The most common form of termination is Class II single parallel termination. This involves one RS series resistor from the chipset to the memory and one RT termination resistor. Typical values for RS and RT are 25 Ohms, although these can be changed to scale the current requirements from the LP2998. This implementation can be seen below in Figure 17. VDD VTT RT RS MEMORY CHIPSET VREF Figure 17. SSTL-Termination Scheme Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 9 LP2998 SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 www.ti.com Pin Descriptions AVIN AND PVIN AVIN and PVIN are the input supply pins for the LP2998. AVIN is used to supply all the internal control circuitry. PVIN, however, is used exclusively to provide the rail voltage for the output stage used to create VTT. These pins have the capability to work off separate supplies, under the condition that AVIN is always greater than or equal to PVIN. For SSTL-18 applications, it is recommended to connect PVIN to the 1.8V rail used for the memory core and AVIN to a rail within its operating range of 2.2V to 5.5V (typically a 2.5V supply). PVIN should always be used with either a 1.8V or 2.5V rail. This prevents the thermal limit from tripping because of excessive internal power dissipation. If the junction temperature exceeds the thermal shutdown threshold, the part will enter a shutdown state identical to the manual shutdown where VTT is tri-stated and VREF remains active. A lower rail, such as 1.5V can be used but it will reduce the maximum output current. Therefore it is not recommended for most termination schemes. VDDQ VDDQ is the input used to create the internal reference voltage for regulating VTT. The reference voltage is generated from a resistor divider of two internal 50k resistors. This ensures that VTT will precisely track VDDQ / 2. The optimal implementation of VDDQ is as a remote sense. This can be achieved by connecting VDDQ directly to the 1.8V rail at the DIMM instead of PVIN. This ensures that the reference voltage precisely tracks the DDR memory rails without a large voltage drop from the power lines. For SSTL-18 applications, VDDQ will be a 1.8V signal, which will create a 0.9V termination voltage at VTT (See Electrical Characteristics Table for exact values of VTT over temperature). VSENSE The purpose of the sense pin is to provide improved remote load regulation. In most motherboard applications, the termination resistors will connect to VTT in a long plane. If the output voltage was regulated only at the output of the LP2998, then the long trace will cause a significant IR drop resulting in a termination voltage lower at one end of the bus than the other. The VSENSE pin can be used to improve this performance by connecting it to the middle of the bus. This will provide a better distribution across the entire termination bus. If remote load regulation is not used, then the VSENSE pin must still be connected to VTT. Care should be taken when a long VSENSE trace is implemented in close proximity to the memory. Noise pickup in the VSENSE trace can cause problems with precise regulation of VTT. A small 0.1uF ceramic capacitor placed next to the VSENSE pin can help filter any high frequency signals and prevent errors. SHUTDOWN The LP2998 contains an active low shutdown pin that can be used for suspend to RAM functionality. In this condition, the VTT output will tri-state while the VREF output remains active providing a constant reference signal for the memory and chipset. During shutdown, VTT should not be exposed to voltages that exceed PVIN. With the shutdown pin asserted low the quiescent current of the LP2998 will drop. However, VDDQ will always maintain its constant impedance of 100k for generating the internal reference. Therefore, to calculate the total power loss in shutdown, both currents need to be considered. For more information refer to the Thermal Dissipation section. The shutdown pin also has an internal pull-up current. Therefore, to turn the part on, the shutdown pin can either be connected to AVIN or left open. VREF VREF provides the buffered output of the internal reference voltage VDDQ / 2. This output should be used to provide the reference voltage for the Northbridge chipset and memory. Since the inputs typically have an extremely high impedance, there should be little current drawn from VREF. For improved performance, an output bypass capacitor can be placed, close to the pin, to help with noise. A ceramic capacitor in the range of 0.1 F to 0.01 F is recommended. This output remains active during the shutdown state and thermal shutdown events for the suspend to RAM functionality. VTT VTT is the regulated output that is used to terminate the bus resistors. It is capable of sinking and sourcing current while regulating the output precisely to VDDQ / 2. The LP2998 is designed to handle continuous currents of up to +/- 1.5A with excellent load regulation. If a transient is expected to last above the maximum continuous current rating for a significant amount of time, then the bulk output capacitor should be sized large enough to prevent an excessive voltage drop. If the LP2998 is to operate in elevated temperatures for long durations, care should be taken to ensure that the maximum operating junction temperature is not exceeded. Proper thermal de-rating should always be used (Please refer to the Thermal Dissipation section). If the junction temperature exceeds the thermal shutdown threshold, VTT will tri-state until the part returns below the temperature hysteresis trip-point. Component Selections INPUT CAPACITOR The LP2998 does not require a capacitor for input stability, but it is recommended for improved performance during large load transients to prevent the input rail from dropping. The input capacitor should be located as close as possible to the PVIN pin. Several recommendations exist and is dependent on the application required. A typical value recommended for AL electrolytic capacitors is 22 F. Ceramic capacitors can also be used. A value in the range of 10 F with X5R or better would be an ideal choice. The input capacitance can be reduced if the LP2998 is placed close to the bulk capacitance from the output of the 1.8V DC-DC converter. For the AVIN pin, a small 0.1uF ceramic capacitor is sufficient to prevent excessive noise from coupling into the device. 10 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 LP2998 www.ti.com SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 OUTPUT CAPACITOR The LP2998 has been designed to be insensitive of output capacitor size or ESR (Equivalent Series Resistance). This allows the flexibility to use any capacitor desired. The choice for output capacitor will be determined solely on the application and the requirements for load transient response of VTT. As a general recommendation the output capacitor should be sized above 100 F with a low ESR for SSTL applications with DDR-SDRAM. The value of ESR should be determined by the maximum current spikes expected and the extent at which the output voltage is allowed to droop. Several capacitor options are available on the market and a few of these are highlighted below: AL - It should be noted that many aluminum electrolytics only specify impedance at a frequency of 120 Hz, which indicates they have poor high frequency performance. Only aluminum electrolytics that have an impedance specified at a higher frequency (100 kHz) should be used for the LP2998. To improve the ESR several AL electrolytics can be combined in parallel for an overall reduction. An important note to be aware of is the extent at which the ESR will change over temperature. Aluminum electrolytic capacitors tend to have rapidly increasing ESR at cold temperatures. Ceramic - Ceramic capacitors typically have a low capacitance, in the range of 10 to 100 F. They also have excellent AC performance for bypassing noise because of very low ESR (typically less than 10 m). However, some dielectric types do not have good capacitance characteristics as a function of voltage and temperature. Because of the typically low value of capacitance, it is recommended to use ceramic capacitors in parallel with another capacitor such as an aluminum electrolytic. A dielectric of X5R or better is recommended for all ceramic capacitors. Hybrid - Several hybrid capacitors such as OS-CON and SP are available from several manufacturers. These offer a large capacitance while maintaining a low ESR. These are the best solution when size and performance are critical, although their cost is typically higher than any other capacitor type. Thermal Dissipation Since the LP2998 is a linear regulator, any current flow from VTT will result in internal power dissipation and heat generation. To prevent damaging the part by exceeding the maximum allowable operating junction temperature, care should be taken to derate the part based on the maximum expected ambient temperature and power dissipation. The maximum allowable internal temperature rise (TRmax) can be calculated given the maximum ambient temperature (TAmax) of the application and the maximum allowable junction temperature (TJmax). TRmax = TJmax - TAmax (1) From this equation, the maximum power dissipation (PDmax) of the part can be calculated: PDmax = TRmax / JA (2) The JA of the LP2998 will depend on several variables: the package used; the thickness of copper; the number of vias and the airflow. For instance, the JA of the SOIC-8 is 163C/W with the package mounted to a standard 8x4 2-layer board with 1oz. copper, no airflow, and 0.5W dissipation at room temperature. This value can be reduced to 151.2C/W by changing to a 3x4 board with 2 oz. copper that is the JEDEC standard. Figure 18 shows how the JA varies with airflow for the two boards mentioned. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 11 LP2998 SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 www.ti.com 180 170 160 150 SOP Board TJA 140 130 120 110 JEDEC Board 100 90 80 0 200 400 600 800 1000 AIRFLOW (Linear Feet per Minute) Figure 18. JA vs Airflow (SOIC-8) Additional improvements can be made by the judicious use of vias to connect the part and dissipate heat to an internal ground plane. Using larger traces and more copper on the top side of the board can also help. With careful layout, it is possible to reduce the JA further than the nominal values shown in Figure 18. Optimizing the JA and placing the LP2998 in a section of a board exposed to lower ambient temperature allows the part to operate with higher power dissipation. The internal power dissipation can be calculated by summing the three main sources of loss: output current at VTT, either sinking or sourcing, and quiescent currents at AVIN and VDDQ. During the active state (when shutdown is not held low) the total internal power dissipation can be calculated from the following equations: PD = PAVIN + PVDDQ + PVTT (3) Where, PAVIN = IAVIN * VAVIN PVDDQ = VVDDQ * IVDDQ = VVDDQ2 x RVDDQ (4) (5) To calculate the maximum power dissipation at VTT, both the sinking and sourcing current conditions need to be examined. Although only one equation will add into the total, VTT cannot source and sink current simultaneously. PVTT = VVTT x ILOAD (Sinking) or PVTT = ( VPVIN - VVTT) x ILOAD (Sourcing) (6) (7) The power dissipation of the LP2998 can also be calculated during the shutdown state. During this condition the output VTT will tri-state. Therefore, that term in the power equation will disappear as it cannot sink or source any current (leakage is negligible). The only losses during shutdown will be the reduced quiescent current at AVIN and the constant impedance that is seen at the VDDQ pin. PD = PAVIN + PVDDQ PAVIN = IAVIN x VAVIN PVDDQ = VVDDQ * IVDDQ = VVDDQ2 x RVDDQ (8) (9) (10) Typical Application Circuits Several different application circuits have been shown in Figure 19 through Figure 28 to illustrate some of the options that are possible in configuring the LP2998. Graphs of the individual circuit performance can be found in the Typical Performance Characteristics section of the datasheet. These curves illustrate how the maximum output current is affected by changes in AVIN and PVIN. SSTL-2 APPLICATIONS For the majority of applications that implement the SSTL-2 termination scheme it is recommended to connect all the input rails to the 2.5V rail. This provides an optimal trade-off between power dissipation and component count and selection. An example of this circuit can be seen in Figure 19. 12 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 LP2998 www.ti.com SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 LP2998 VREF = 1.25V VREF SD SD + VDDQ VDDQ = 2.5V VDD = 2.5V CIN + AVIN VSENSE PVIN VTT CREF VTT = 1.25V + GND COUT Figure 19. Recommended SSTL-2 Implementation If power dissipation or efficiency is a major concern then the LP2998 has the ability to operate on split power rails (see Figure 20). The output stage (PVIN) can be operated on a lower rail such as 1.8V and the analog circuitry (AVIN) can be connected to a higher rail such as 2.5V, 3.3V or 5V. This allows the internal power dissipation to be lowered when sourcing current from VTT. The disadvantage of this circuit is that the maximum continuous current is reduced because of the lower rail voltage, although it is adequate for all motherboard SSTL-2 applications. Increasing the output capacitance can also help if periods of large load transients will be encountered. LP2998 VREF = 1.25V VREF SD SD + VDDQ = 2.5V VDDQ AVIN = 2.2V to 5.5V AVIN VSENSE PVIN PVIN = 1.8V VTT = 1.25V VTT + CIN CREF + GND COUT Figure 20. Lower Power Dissipation SSTL-2 Implementation The third option for SSTL-2 applications in the situation that a 1.8V rail is not available and it is not desirable to use 2.5V, is to connect the LP2998 power rail to 3.3V (see Figure 21). In this situation AVIN will be limited to operation on the 3.3V or 5V rail as PVIN can never exceed AVIN. This configuration has the ability to provide the maximum continuous output current at the downside of higher thermal dissipation. Care should be taken to prevent the LP2998 from experiencing large current levels which cause the device to exceed the maximum operating junction temperature. Because of this risk it is not recommended to supply the output stage with a voltage higher than a nominal 3.3V rail. LP2998 VREF SD SD VREF = 1.25V + VDDQ VDDQ = 2.5V AVIN = 3.3V or 5V AVIN PVIN = 3.3V VSENSE PVIN CIN + CREF VTT = 1.25V VTT GND + COUT Figure 21. SSTL-2 Implementation With Higher Voltage Rails Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 13 LP2998 SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 www.ti.com DDR-II APPLICATIONS With the separate VDDQ pin and an internal resistor divider it is possible to use the LP2998 in applications utilizing DDR-II memory. Figure 22 and Figure 23 show several implementations of recommended circuits with output curves displayed in the Typical Performance Characteristics. Figure 22 shows the recommended circuit configuration for DDR-II applications. The output stage is connected to the 1.8V rail and the AVIN pin can be connected to either a 2.5, 3.3V or 5.5V rail. LP2998 + 0.01 PF AVIN = 2.5V AVIN VDDQ = 1.8V VDDQ VSENSE PVIN + VREF = 0.9V VREF SD SD VTT = 0.9V VTT + GND 47 PF 220 PF Figure 22. Recommended DDR-II Termination If it is not desirable to use the 1.8V rail it is possible to connect the output stage to a 3.3V rail. Care should be taken to not exceed the maximum operating junction temperature as the thermal dissipation increases with lower VTT output voltages. For this reason it is not recommended to power PVIN with a rail higher than the nominal 3.3V. The advantage of this configuration is that it has the ability to source and sink a higher maximum continuous current. LP2998 VDDQ = 1.8V VREF = 0.9V VREF SD SD + VDDQ AVIN = 3.3V or 5.5V AVIN PVIN = 3.3V VSENSE PVIN CIN + CREF VTT = 0.9V VTT GND + COUT Figure 23. DDR-II Termination With Higher Voltage Rails LEVEL SHIFTING If standards other than SSTL-2 are required, such as SSTL-3, it may be necessary to use a different scaling factor than 0.5 times VDDQ for regulating the output voltage. Several options are available to scale the output to any voltage required. One method is to level shift the output by using feedback resistors from VTT to the VSENSE pin. This has been illustrated in Figure 24 and Figure 25. Figure 24 shows how to use two resistors to level shift VTT above the internal reference voltage of VDDQ/2. To calculate the exact voltage at VTT the following equation can be used. VTT = VDDQ/2 (1 + R1/R2) 14 (11) Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 LP2998 www.ti.com SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 LP2998 VDDQ VDDQ VDD VTT VTT AVIN R1 PVIN CIN + VSENSE + GND COUT R2 Figure 24. Increasing VTT by Level Shifting Conversely, the R2 resistor can be placed between VSENSE and VDDQ to shift the VTT output lower than the internal reference voltage of VDDQ/2. The equation relating to VTT and the resistors can be used as shown: VTT = VDDQ/2 (1 - R1/R2) (12) LP2998 VDDQ VDDQ VDD R2 VSENSE AVIN R1 + CIN VTT VTT PVIN + GND COUT Figure 25. Decreasing VTT by Level Shifting HSTL APPLICATIONS The LP2998 can be easily adapted for HSTL applications by connecting VDDQ to the 1.5V rail. This will produce a VTT and VREF voltage of approximately 0.75V for the termination resistors. AVIN and PVIN should be connected to a 2.5V rail for optimal performance. LP2998 VREF SD SD VREF = 0.75V + VDDQ VDDQ = 1.5V AVIN VDD = 2.5V VSENSE PVIN CIN + CREF VTT = 0.75V VTT GND + COUT Figure 26. HSTL Application QDR APPLICATIONS Quad data rate (QDR) applications utilize multiple channels for improved memory performance. However, this increase in bus lines increases the current levels required for termination. The recommended approach in terminating multiple channels is to use a dedicated LP2998 for each channel. This simplifies layout and reduces the internal power dissipation for each regulator. Separate VREF signals can be used for each DIMM bank from the corresponding regulator with the chipset reference provided by a local resistor divider or one of the LP2998 signals. Because VREF and VTT are expected to track and the part to part variations are minor, there should be little difference between the reference signals of each LP2998. Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 15 LP2998 SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 www.ti.com OUTPUT CAPACITOR SELECTION For applications utilizing the LP2998 to terminate SSTL-2 I/O signals the typical application circuit shown in Figure 27 can be implemented. LP2998 + AVIN = 2.5V AVIN VDDQ = 1.8V VDDQ CREF VSENSE PVIN CIN VREF = 0.9V VREF SD SD VTT = 0.9V VTT + + GND COUT Figure 27. Typical SSTL-2 Application Circuit This circuit permits termination in a minimum amount of board space and component count. Capacitor selection can be varied depending on the number of lines terminated and the maximum load transient. However, with motherboards and other applications where VTT is distributed across a long plane, it is recommended to use multiple bulk capacitors in addition to high frequency decoupling. Figure 28 depicts an example circuit where 2 bulk output capacitors could be situated at both ends of the VTT plane for optimal placement. Large aluminum electrolytic capacitors are typically used for their low ESR and low cost. LP2998 SD VDDQ = 2.5V VDDQ VDD = 2.5V AVIN 47 PF + 0.01 PF VSENSE PVIN + VREF = 1.25V VREF SD VTT GND VTT = 1.25V + 330 PF + 330 PF Figure 28. Typical SSTL-2 Application Circuit for Motherboards In most PC applications, an extensive amount of decoupling is required because of the long interconnects encountered with the DDR-SDRAM DIMMs mounted on modules. As a result, bulk aluminum electrolytic capacitors in the range of 1000uF are typically used. PCB Layout Considerations 1. The input capacitor for the power rail should be placed as close as possible to the PVIN pin. 2. VSENSE should be connected to the VTT termination bus at the point where regulation is required. For motherboard applications an ideal location would be at the center of the termination bus. 3. VDDQ can be connected remotely to the VDDQ rail input at either the DIMM or the Chipset. This provides the most accurate point for creating the reference voltage. 4. For improved thermal performance excessive top side copper should be used to dissipate heat from the package. Numerous vias from the ground connection to the internal ground plane will help. Additionally these can be located underneath the package if manufacturing standards permit. 5. Care should be taken when routing the VSENSE trace to avoid noise pickup from switching I/O signals. A 0.1uF ceramic capacitor located close to the SENSE can also be used to filter any unwanted high frequency signal. This can be an issue especially if long SENSE traces are used. 6. VREF should be bypassed with a 0.01 F or 0.1 F ceramic capacitor for improved performance. This capacitor should be located as close as possible to the VREF pin. 16 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 LP2998 www.ti.com SNVS521I - DECEMBER 2007 - REVISED APRIL 2013 REVISION HISTORY Changes from Revision H (April 2013) to Revision I * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 16 Submit Documentation Feedback Copyright (c) 2007-2013, Texas Instruments Incorporated Product Folder Links: LP2998 17 PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Top-Side Markings (3) (4) LP2998MA/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LP2998 MA LP2998MAE/NOPB ACTIVE SOIC D 8 250 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LP2998 MA LP2998MAX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LP2998 MA LP2998MR/NOPB ACTIVE SO PowerPAD DDA 8 95 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 LP2998 MR LP2998MRE/NOPB ACTIVE SO PowerPAD DDA 8 250 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 LP2998 MR LP2998MRX/NOPB ACTIVE SO PowerPAD DDA 8 2500 Green (RoHS & no Sb/Br) CU SN Level-3-260C-168 HR -40 to 125 LP2998 MR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 11-Apr-2013 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing LP2998MAE/NOPB SOIC SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant D 8 250 178.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LP2998MAX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LP2998MRE/NOPB SO Power PAD DDA 8 250 178.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LP2998MRX/NOPB SO Power PAD DDA 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 8-Apr-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP2998MAE/NOPB SOIC D LP2998MAX/NOPB SOIC D 8 250 210.0 185.0 35.0 8 2500 367.0 367.0 35.0 LP2998MRE/NOPB SO PowerPAD DDA LP2998MRX/NOPB SO PowerPAD DDA 8 250 213.0 191.0 55.0 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 MECHANICAL DATA DDA0008A MRA08A (Rev D) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated