NCV1117ST33T3G - ON Semiconductor

April, 2012 − Rev. 24

1Publication Order Number:

NCP1117/D

NCP1117, NCV1117

1.0 A Low-Dropout Positive

Fixed and Adjustable

Voltage Regulators

The NCP1117 series are low dropout positive voltage regulators that

are capable of providing an output current that is in excess of 1.0 A

with a maximum dropout voltage of 1.2 V at 800 mA over

temperature. This series contains nine fixed output voltages of 1.5 V,

1.8 V, 1.9 V, 2.0 V, 2.5 V, 2.85 V, 3.3 V, 5.0 V, and 12 V that have no

minimum load requirement to maintain regulation. Also included is an

adjustable output version that can be programmed from 1.25 V to

18.8 V with two external resistors. On chip trimming adjusts the

reference/output voltage to within ±1.0% accuracy. Internal protection

features consist of output current limiting, safe operating area

compensation, and thermal shutdown. The NCP1117 series can

operate with up to 20 V input. Devices are available in SOT−223 and

DPAK packages.

Features

•Output Current in Excess of 1.0 A

•1.2 V Maximum Dropout Voltage at 800 mA Over Temperature

•Fixed Output Voltages of 1.5 V, 1.8 V, 1.9 V, 2.0 V, 2.5 V, 2.85 V,

3.3 V, 5.0 V, and 12 V

•Adjustable Output Voltage Option

•No Minimum Load Requirement for Fixed Voltage Output Devices

•Reference/Output Voltage Trimmed to ±1.0%

•Current Limit, Safe Operating and Thermal Shutdown Protection

•Operation to 20 V Input

•NCV Prefix for Automotive and Other Applications Requiring Site

and Control Changes

•Pb−Free Packages are Available

Applications

•Consumer and Industrial Equipment Point of Regulation

•Active SCSI Termination for 2.85 V Version

•Switching Power Supply Post Regulation

•Hard Drive Controllers

•Battery Chargers

2Output

Input NCP1117

XTXX

Figure 1. Fixed

Output Regulator

2Output

Input NCP1117

XTA

Figure 2. Adjustable

Output Regulator

3NCP1117

XT285

110 W

4.75 V

5.25 V

18 to 27

Lines

Figure 3. Active SCSI Bus Terminator

TYPICAL APPLICATIONS

SOT−223

ST SUFFIX

CASE 318H

DPAK

DT SUFFIX

CASE 369C

Pin: 1. Adjust/Ground

2. Output

3. Input

Heatsink tab is connected to Pin 2.

See detailed ordering and shipping information in the package

dimensions section on page 12 of this data sheet.

ORDERING INFORMATION

See general marking information in the device marking

section on page 15 of this data sheet.

DEVICE MARKING INFORMATION

123

Tab

(Top View)

http://onsemi.com

NCP1117, NCV1117

http://onsemi.com

MAXIMUM RATINGS

Rating Symbol Value Unit

Input Voltage (Note 1) Vin 20 V

Output Short Circuit Duration (Notes 2 and 3) −Infinite −

Power Dissipation and Thermal Characteristics

Case 318H (SOT−223)

Power Dissipation (Note 2)

Thermal Resistance, Junction−to−Ambient, Minimum Size Pad

Thermal Resistance, Junction−to−Case

Case 369A (DPAK)

Power Dissipation (Note 2)

Thermal Resistance, Junction−to−Ambient, Minimum Size Pad

Thermal Resistance, Junction−to−Case

RqJA

RqJC

RqJA

RqJC

Internally Limited

160

Internally Limited

6.0

°C/W

Maximum Die Junction Temperature Range TJ−55 to 150 °C

Storage Temperature Range Tstg −65 to 150 °C

Operating Ambient Temperature Range

NCP1117

NCV1117

TA0 to +125

−40 to +125

°C

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the

Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect

device reliability.

1. This device series contains ESD protection and exceeds the following tests:

Human Body Model (HBM), Class 2, 2000 V

Machine Model (MM), Class B, 200 V

Charge Device Model (CDM), Class IV, 2000 V.

2. Internal thermal shutdown protection limits the die temperature to approximately 175°C. Proper heatsinking is required to prevent activation.

The maximum package power dissipation is:

PD+TJ(max) *TA

RqJA

3. The regulator output current must not exceed 1.0 A with Vin greater than 12 V.

NCP1117, NCV1117

http://onsemi.com

ELECTRICAL CHARACTERISTICS (Cin = 10 mF, C out = 10 mF, for typical value TA = 25°C, for min and max values TA is the

operating ambient temperature range that applies unless otherwise noted. (Note 4)

Characteristic Symbol Min Typ Max Unit

Reference Voltage, Adjustable Output Devices

(Vin–Vout = 2.0 V, Iout = 10 mA, TA = 25°C)

(Vin–Vout = 1.4 V to 10 V, Iout = 10 mA to 800 mA) (Note 4)

Vref

1.238

1.225

1.25

−

1.262

1.270

Output Voltage, Fixed Output Devices

1.5 V (Vin = 3.5 V, Iout = 10 mA, TA = 25 °C)

(Vin = 2.9 V to 11.5 V, Iout = 0 mA to 800 mA) (Note 4)

1.8 V (Vin = 3.8 V, Iout = 10 mA, TA = 25 °C)

(Vin = 3.2 V to 11.8 V, Iout = 0 mA to 800 mA) (Note 4)

1.9 V (Vin = 3.9 V, Iout = 10 mA, TA = 25 °C)

(Vin = 3.3 V to 11.9 V, Iout = 0 mA to 800 mA) (Note 4)

2.0 V (Vin = 4.0 V, Iout = 10 mA, TA = 25 °C)

(Vin = 3.4 V to 12 V, Iout = 0 mA to 800 mA) (Note 4)

2.5 V (Vin = 4.5 V, Iout = 10 mA, TA = 25 °C)

(Vin = 3.9 V to 10 V, Iout = 0 mA to 800 mA,) (Note 4)

2.85 V (Vin = 4.85 V, Iout = 10 mA, TA = 25 °C)

(Vin = 4.25 V to 10 V, Iout = 0 mA to 800 mA) (Note 4)

(Vin = 4.0 V, Iout = 0 mA to 500 mA) (Note 4)

3.3 V (Vin = 5.3 V, Iout = 10 mA, TA = 25 °C)

(Vin = 4.75 V to 10 V, Iout = 0 mA to 800 mA) (Note 4)

5.0 V (Vin = 7.0 V, Iout = 10 mA, TA = 25 °C)

(Vin = 6.5 V to 12 V, Iout = 0 mA to 800 mA) (Note 4)

12 V (Vin = 14 V, Iout = 10 mA, TA = 25 °C)

(Vin = 13.5 V to 20 V, Iout = 0 mA to 800 mA) (Note 4)

Vout

1.485

1.470

1.782

1.755

1.872

1.862

1.970

1.960

2.475

2.450

2.821

2.790

3.267

3.235

4.950

4.900

11.880

11.760

1.500

−

1.800

−

1.900

2.000

−

2.500

−

2.850

−

3.300

−

5.000

−

12.000

−

1.515

1.530

1.818

1.845

1.929

1.938

2.030

2.040

2.525

2.550

2.879

2.910

3.333

3.365

5.050

5.100

12.120

12.240

Line Regulation (Note 5) Adjustable (Vin = 2.75 V to 16.25 V, Iout = 10 mA) Regline −0.04 0.1 %

1.5 V (Vin = 2.9 V to 11.5 V, Iout = 0 mA)

1.8 V (Vin = 3.2 V to 11.8 V, Iout = 0 mA)

1.9 V (Vin = 3.3 V to 11.9 V, Iout = 0 mA)

2.0 V (Vin = 3.4 V to 12 V, Iout = 0 mA)

2.5 V (Vin = 3.9 V to 10 V, Iout = 0 mA)

2.85 V (Vin = 4.25 V to 10 V, Iout = 0 mA)

3.3 V (Vin = 4.75 V to 15 V, Iout = 0 mA)

5.0 V (Vin = 6.5 V to 15 V, Iout = 0 mA)

12 V (Vin = 13.5 V to 20 V, Iout = 0 mA)

−

0.3

0.4

0.5

0.8

0.9

1.0

2.5

3.0

4.5

6.0

7.5

Load Regulation (Note 5) Adjustable (Iout = 10 mA to 800 mA, Vin = 4.25 V) Regline −0.2 0.4 %

1.5 V (Iout = 0 mA to 800 mA, Vin = 2.9 V)

1.8 V (Iout = 0 mA to 800 mA, Vin = 3.2 V)

1.9 V (Iout = 0 mA to 800 mA, Vin = 3.3 V)

2.0 V (Iout = 0 mA to 800 mA, Vin = 3.4 V)

2.5 V (Iout = 0 mA to 800 mA, Vin = 3.9 V)

2.85 V (Iout = 0 mA to 800 mA, Vin = 4.25 V)

3.3 V (Iout = 0 mA to 800 mA, Vin = 4.75 V)

5.0 V (Iout = 0 mA to 800 mA, Vin = 6.5 V)

12 V (Iout = 0 mA to 800 mA, Vin = 13.5 V)

−

2.3

2.6

2.7

3.0

3.3

3.8

4.3

6.7

5.5

6.0

7.5

8.0

4. NCP1117: Tlow = 0°C , Thigh = 125°C

NCV1117: Tlow = −40°C, Thigh = 125°C

5. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.

NCP1117, NCV1117

http://onsemi.com

ELECTRICAL CHARACTERISTICS (Cin = 10 mF, C out = 10 mF, for typical value TA = 25°C, for min and max values TA is the

operating ambient temperature range that applies unless otherwise noted. (Note 6)

Characteristic Symbol Min Typ Max Unit

Dropout Voltage (Measured at Vout − 100 mV)

(Iout = 100 mA)

(Iout = 500 mA)

(Iout = 800 mA)

Vin−Vout

−

0.95

1.01

1.07

1.10

1.15

1.20

Output Current Limit (Vin−Vout = 5.0 V, TA = 25°C, Note 7) Iout 1000 1500 2200 mA

Minimum Required Load Current for Regulation, Adjustable Output Devices

(Vin = 15 V)

IL(min) −0.8 5.0 mA

Quiescent Current

1.5 V (Vin = 11.5 V)

1.8 V (Vin = 11.8 V)

1.9 V (Vin = 11.9 V)

2.0 V (Vin = 12 V)

2.5 V (Vin = 10 V)

2.85 V (Vin = 10 V)

3.3 V (Vin = 15 V)

5.0 V (Vin = 15 V)

12 V (Vin = 20 V)

−

3.6

4.2

4.3

4.5

5.2

5.5

6.0

Thermal Regulation (TA = 25°C, 30 ms Pulse) −0.01 0.1 %/W

Ripple Rejection (Vin−Vout = 6.4 V, Iout = 500 mA, 10 Vpp 120 Hz Sinewave)

Adjustable

1.5 V

1.8 V

1.9 V

2.0 V

2.5 V

2.85 V

3.3 V

5.0 V

12 V

−

Adjustment Pin Current (Vin = 11.25 V, Iout = 800 mA) Iadj −52 120 mA

Adjust Pin Current Change

(Vin−Vout = 1.4 V to 10 V, Iout = 10 mA to 800 mA)

DIadj −0.4 5.0 mA

Temperature Stability ST−0.5 −%

Long Term Stability (TA = 25°C, 1000 Hrs End Point Measurement) St−0.3 −%

RMS Output Noise (f = 10 Hz to 10 kHz) N−0.003 −%Vout

6. NCP1117: Tlow = 0°C , Thigh = 125°C

NCV1117: Tlow = −40°C, Thigh = 125°C

7. The regulator output current must not exceed 1.0 A with Vin greater than 12 V.

NCP1117, NCV1117

http://onsemi.com

Vin − Vout, DROPOUT VOLTAGE (V)

TA, AMBIENT TEMPERATURE (°C)

Iadj, ADJUST PIN CURRENT (mA)

Iout = 10 mA

100

Figure 4. Output Voltage Change

vs. Temperature

Figure 5. Dropout Voltage

vs. Output Current

Figure 6. Output Short Circuit Current

vs. Differential Voltage

Figure 7. Output Short Circuit Current

vs. Temperature

Figure 8. Adjust Pin Current

vs. Temperature

Figure 9. Quiescent Current Change

vs. Temperature

0.5

1.0

1.5

2.0

0 2 4 6 8 101214161820

Load pulsed at 1.0% duty cycle

Vin − Vout, VOLTAGE DIFFERENTIAL (V)

Iout, OUTPUT CURRENT (A)

TJ = 25°C

0.2

0.4

0.6

0.8

1.0

1.2

1.4

0 200 400 600 800 1000

Load pulsed at 1.0% duty cycle

Iout, OUTPUT CURRENT (mA)

TJ = −40°C

TJ = 25°C

TJ = 125°C

Vout, OUTPUT VOLTAGE CHANGE (%)

−2.0

−1.5

−1.0

−0.5

0.5

1.0

1.5

2.0

−50 −25 0 25 50 75 100 125 150

TA, AMBIENT TEMPERATURE (°C)

Vin = Vout + 3.0 V

Iout = 10 mA

Adj, 1.5 V,

1.8 V, 2.0 V,

2.5 V

2.85 V, 3.3 V,

5.0 V, 12.0 V

1.0

1.2

1.4

1.6

1.8

2.0

−50 −25 0 25 50 75 100 125 150

−20

−15

−10

−5.0

5.0

−50 −25 0 25 50 75 100 125 150

TA, AMBIENT TEMPERATURE (°C)

Iout, OUTPUT CURRENT (A)

Vin = 5.0 V

Load pulsed at 1.0% duty cycle

TA, AMBIENT TEMPERATURE (°C)

IQ, QUIESCENT CURRENT CHANGE (%)

−50 −25 0 25 50 75 100 125 150

NCP1117, NCV1117

http://onsemi.com

100

10 100 1.0 k 10 k 100 k

100

0 200 400 600 800 1000

Iout, OUTPUT CURRENT (mA)

RR, RIPPLE REJECTION (dB)

fripple = 20 kHz

Vripple v 0.5 VP−P

Vout = 5.0 V

Vin − Vout = 3.0 V

Cout = 10 mF

Cadj = 25 mF

TA = 25°C

fripple, RIPPLE FREQUENCY (Hz)

RR, RIPPLE REJECTION (dB)

Vout = 5.0 V

Vin − Vout = 3.0 V

Iout = 0.5 A

Cout = 10 mF

Cadj = 25 mF, f > 60 Hz

Vripple v 3.0 VP−P Vripple v 0.5 VP−P

Vin − Vout w 3.0 V

Figure 10. NCP1117XTA Ripple Rejection

vs. Output Current

Figure 11. NCP1117XTA Ripple Rejection

vs. Frequency

Figure 12. Output Capacitance vs. ESR Figure 13. Typical ESR vs. Output Current

fripple = 120 Hz

Vripple v 3.0 VP−P

Vin − Vout w Vdropout

Cadj = 200 mF, f v 60 Hz

TA = 25°C

0.1

100

0.001 0.01 0.1 1 10

ESR, EQUIVALENT SERIES RESISTANCE (W)

OUTPUT CAPACITANCE (mF)

Vin = 3.0 V

Vout = 1.25 V

Iload = 5 mA − 1 A

Cin = 10 mF MLCC

TJ = 25°C

Region of Instability

Region of Stability

0.01

0.1

0 100 500 900 1000

Iout, OUTPUT CURRENT (mA)

ESR, EQUIVALENT SERIES RESISTANCE (W)

Vin = 3.0 V

Vout = 1.25 V

Cin = 10 mF MLCC

Cout = 10 mF

TJ = 25°C

Region of Instability

Region of Stability

200 600300 700400 800

50E−9

100E−9

150E−9

200E−9

250E−9

10 100 1.0 k 10 k 100 k

FREQUENCY (Hz)

V/sqrt (Hz)

Cin = 10 mF Tantalum

Cout = 10 mF Tantalum

Vin − Vout = 3.0 V

Figure 14. Output Spectral Noise Density vs.

Frequency, Vout = 1V5

300E−9

350E−9

1 A

0.5 A

0.1 A

NCP1117, NCV1117

http://onsemi.com

t, TIME (ms)

−20

7.5

6.5

0 40 80 120 160

OUTPUT VOLTAGE

DEVIATION (mV)

INPUT

VOLTAGE (V)

200

Figure 15. NCP1117XT285

Line Transient Response

Figure 16. NCP1117XT285

Load Transient Response

Figure 17. NCP1117XT50

Line Transient Response

Figure 18. NCP1117XT50

Load Transient Response

Cin = 10 mF

Cout = 10 mF

Vin = 6.5 V

Preload = 0.1 A

TA = 25°C

t, TIME (ms)

0.5

0.1

−0.1

0 40 80 120 160

LOAD CURRENT

CHANGE (A)

OUTPUT VOLTAGE

DEVIATION (V)

200

Cin = 10 mF

Cout = 10 mF

Vin = 4.5 V

Preload = 0.1 A

TA = 25°C

t, TIME (ms)

0.5

0.1

−0.1

0 40 80 120 160

LOAD CURRENT

CHANGE (A)

OUTPUT VOLTAGE

DEVIATION (V)

200

t, TIME (ms)

−20

5.25

4.25

0 40 80 120 160

OUTPUT VOLTAGE

DEVIATION (mV)

INPUT

VOLTAGE (V)

200

Cin = 1.0 mF

Cout = 10 mF

Iout = 0.1 A

TA = 25°C

Cin = 1.0 mF

Cout = 10 mF

Iout = 0.1 A

TA = 25°C

Figure 19. NCP1117XT12 Line

Transient Response

Figure 20. NCP1117XT12 Load

Transient Response

t, TIME (ms)

Cin = 10 mF

Cout = 10 mF

Vin = 13.5 V

Preload = 0.1 A

TA = 25°C

0.5

0.1

−0.1

0 40 80 120 160 200

LOAD CURRENT

CHANGE (A)

OUTPUT VOLTAGE

DEVIATION (V)

t, TIME (ms)

−20

14.5

13.5

0 40 80 120 160

OUTPUT VOLTAGE

DEVIATION (mV)

INPUT

VOLTAGE (V)

200

Cin = 1.0 mF

Cout = 10 mF

Iout = 0.1 A

TA = 25°C

NCP1117, NCV1117

http://onsemi.com

100

120

140

160

180

0.4

0.6

0.8

1.0

1.2

1.4

1.6

010203025155.0

L, LENGTH OF COPPER (mm)

PD(max) for TA = 50°C

100

010203025155.0

L, LENGTH OF COPPER (mm)

0.6

0.8

1.0

1.2

1.4

1.6

Figure 21. SOT−223 Thermal Resistance and Maximum

Power Dissipation vs. P.C.B. Copper Length

RqJA, THERMAL RESISTANCE,

JUNCTION−TO−AIR (°CW)

PD, MAXIMUM POWER DISSIPATION (W)

RqJA, THERMAL RESISTANCE,

JUNCTION−TO−AIR (°CW)

0.4

Figure 22. DPAK Thermal Resistance and Maximum

Power Dissipation vs. P.C.B. Copper Length

Minimum

Size Pad

PD, MAXIMUM POWER DISSIPATION (W)

ÎÎÎÎ

2.0 oz. Copper

RqJA

Minimum

Size Pad

PD(max) for TA = 50°C

RqJA

2.0 oz. Copper

ÎÎÎ

NCP1117, NCV1117

http://onsemi.com

APPLICATIONS INFORMATION

Introduction

The NCP1117 features a significant reduction in dropout

voltage along with enhanced output voltage accuracy and

temperature stability when compared to older industry

standard three−terminal adjustable regulators. These

devices contain output current limiting, safe operating area

compensation and thermal shutdown protection making

them designer friendly for powering numerous consumer

and industrial products. The NCP1117 series is pin

compatible with the older LM317 and its derivative device

types.

Output Voltage

The typical application circuits for the fixed and

adjustable output regulators are shown in Figures 23 and 24.

The adjustable devices are floating voltage regulators. They

develop and maintain the nominal 1.25 V reference voltage

between the output and adjust pins. The reference voltage is

programmed to a constant current source by resistor R1, and

this current flows through R2 to ground to set the output

voltage. The programmed current level is usually selected to

be greater than the specified 5.0 mA minimum that is

required for regulation. Since the adjust pin current, Iadj, is

significantly lower and constant with respect to the

programmed load current, it generates a small output

voltage error that can usually be ignored. For the fixed

output devices R1 and R2 are included within the device and

the ground current Ignd, ranges from 3.0 mA to 5.0 mA

depending upon the output voltage.

External Capacitors

Input bypass capacitor Cin may be required for regulator

stability if the device is located more than a few inches from

the power source. This capacitor will reduce the circuit’s

sensitivity when powered from a complex source impedance

and significantly enhance the output transient response. The

input bypass capacitor should be mounted with the shortest

possible track length directly across the regulator’s input

and ground terminals. A 10 mF ceramic or tantalum

capacitor should be adequate for most applications.

Figure 23. Fixed Output Regulator

2Output

Input NCP1117

XTXX

Cout

Cin

Ignd

Frequency compensation for the regulator is provided by

capacitor Cout and its use is mandatory to ensure output

stability. A minimum capacitance value of 4.7 mF with an

equivalent series resistance (ESR) that is within the limits of

33 mW (typ) to 2.2 W is required. See Figures 12 and 13. The

capacitor type can be ceramic, tantalum, or aluminum

electrolytic as long as it meets the minimum capacitance

value and ESR limits over the circuit’s entire operating

temperature range. Higher values of output capacitance can

be used to enhance loop stability and transient response with

the additional benefit of reducing output noise.

Figure 24. Adjustable Output Regulator

2Output

Input NCP1117

XTA

Cout

Cin

Iadj

+Cadj

Vref R1

Vout +Vref ǒ1)R2

R1Ǔ)Iadj R2

The output ripple will increase linearly for fixed and

adjustable devices as the ratio of output voltage to the

reference voltage increases. For example, with a 12 V

regulator, the output ripple will increase by 12 V/1.25 V or

9.6 and the ripple rejection will decrease by 20 log of this

ratio or 19.6 dB. The loss of ripple rejection can be restored

to the values shown with the addition of bypass capacitor

Cadj, shown in Figure 24. The reactance of Cadj at the ripple

frequency must be less than the resistance of R1. The value

of R1 can be selected to provide the minimum required load

current to maintain regulation and is usually in the range of

100 W to 200 W.

Cadj u1

2pfripple R1

The minimum required capacitance can be calculated

from the above formula. When using the device in an

application that is powered from the AC line via a

transformer and a full wave bridge, the value for Cadj is:

fripple +120 Hz, R1 +120 W, then Cadj u11.1 mF

The value for Cadj is significantly reduced in applications

where the input ripple frequency is high. If used as a post

regulator in a switching converter under the following

conditions:

fripple +50 kHz, R1 +120 W, then Cadj u0.027 mF

Figures 10 and 11 shows the level of ripple rejection that

is obtainable with the adjust pin properly bypassed.

NCP1117, NCV1117

http://onsemi.com

Protection Diodes

The NCP1117 family has two internal low impedance

diode paths that normally do not require protection when

used in the typical regulator applications. The first path

connects between Vout and Vin, and it can withstand a peak

surge current of about 15 A. Normal cycling of Vin cannot

generate a current surge of this magnitude. Only when Vin

is shorted or crowbarred to ground and Cout is greater than

50 mF, it becomes possible for device damage to occur.

Under these conditions, diode D1 is required to protect the

device. The second path connects between Cadj and V

out, and

it can withstand a peak surge current of about 150 mA.

Protection diode D2 is required if the output is shorted or

crowbarred to ground and Cadj is greater than 1.0 mF.

Figure 25. Protection Diode Placement

2Output

Input NCP1117

XTA

Cout

Cin

+Cadj

1N4001

A combination of protection diodes D1 and D2 may be

required in the event that Vin is shorted to ground and Cadj

is greater than 50 mF. The peak current capability stated for

the internal diodes are for a time of 100 ms with a junction

temperature of 25°C. These values may vary and are to be

used as a general guide.

Load Regulation

The NCP1117 series is capable of providing excellent

load regulation; but since these are three terminal devices,

only partial remote load sensing is possible. There are two

conditions that must be met to achieve the maximum

available load regulation performance. The first is that the

top side of programming resistor R1 should be connected as

close to the regulator case as practicable. This will minimize

the voltage drop caused by wiring resistance RW + from

appearing in series with reference voltage that is across R1.

The second condition is that the ground end of R2 should be

connected directly to the load. This allows true Kelvin

sensing where the regulator compensates for the voltage

drop caused by wiring resistance RW −.

Figure 26. Load Sensing

2Output

Input NCP1117

XTA

+Cout

Cin R1

Remote

Load

RW+

RW−

Thermal Considerations

This series contains an internal thermal limiting circuit

that is designed to protect the regulator in the event that the

maximum junction temperature is exceeded. When

activated, typically at 175°C, the regulator output switches

off and then back on as the die cools. As a result, if the device

is continuously operated in an overheated condition, the

output will appear to be oscillating. This feature provides

protection from a catastrophic device failure due to

accidental overheating. It is not intended to be used as a

substitute for proper heatsinking. The maximum device

power dissipation can be calculated by:

PD+TJ(max) *TA

RqJA

The devices are available in surface mount SOT−223 and

DPAK packages. Each package has an exposed metal tab

that is specifically designed to reduce the junction to air

thermal resistance, RqJA, by utilizing the printed circuit

board copper as a heat dissipater. Figures 21 and 22 show

typical RqJA values that can be obtained from a square

pattern using economical single sided 2.0 ounce copper

board material. The final product thermal limits should be

tested and quantified in order to insure acceptable

performance and reliability. The actual RqJA can vary

considerably from the graphs shown. This will be due to any

changes made in the copper aspect ratio of the final layout,

adjacent heat sources, and air flow.

NCP1117, NCV1117

http://onsemi.com

Figure 27. Constant Current Regulator Figure 28. Slow Turn−On Regulator

Figure 29. Regulator with Shutdown Figure 30. Digitally Controlled Regulator

Figure 31. Battery Backed−Up Power Supply Figure 32. Adjusting Output of Fixed

Voltage Regulators

The 50 W resistor that is in series with the ground pin of the

upper regulator level shifts its output 300 mV higher than the

lower regulator. This keeps the lower regulator off until the

input source is removed.

Resistor R2 sets the maximum output voltage. Each

transistor reduces the output voltage when turned on.

Constant Current

Output

Input NCP1117

XTA

Iout +Vref

R)Iadj

2Output

Input NCP1117

XTA

1N4001

50 k

2N2907

2Output

Input NCP1117

XTA

120

2N2222

360

1.0 k

Output Control

Off

2Output

Input NCP1117

XTA

2N2222

50 W

2Output

Input NCP1117

XT50

RCHG

NCP1117

XT50

−

6.6 V

5.3 V AC Line

5.0 V Battery

2Output

Input NCP1117

XT50

+10

2.0 k

5.0 V to

12 V

Vout(Off) +Vref

Output Voltage Control

NCP1117, NCV1117

http://onsemi.com

ORDERING INFORMATION

Device Nominal Output Voltage Package Shipping†

NCP1117DTA

Adjustable

DPAK

75 Units / Rail

NCP1117DTAG DPAK

(Pb−Free)

NCP1117DTARK DPAK

2500 / Tape & Reel

NCP1117DTARKG DPAK

(Pb−Free)

NCP1117DTAT5 DPAK

NCP1117DTAT5G DPAK

(Pb−Free)

NCP1117STAT3 SOT−223

4000 / Tape & Reel

NCP1117STAT3G SOT−223

(Pb−Free)

NCP1117DT12

DPAK

75 Units / Rail

NCP1117DT12G DPAK

(Pb−Free)

NCP1117DT12RK DPAK

2500 / Tape & Reel

NCP1117DT12RKG DPAK

(Pb−Free)

NCP1117ST12T3 SOT−223

4000 / Tape & Reel

NCP1117ST12T3G SOT−223

(Pb−Free)

NCP1117DT15

1.5

DPAK

75 Units / Rail

NCP1117DT15G DPAK

(Pb−Free)

NCP1117DT15RK DPAK

2500 / Tape & Reel

NCP1117DT15RKG DPAK

(Pb−Free)

NCP1117ST15T3 SOT−223

4000 / Tape & Reel

NCP1117ST15T3G SOT−223

(Pb−Free)

NCP1117DT18

1.8

DPAK

75 Units / Rail

NCP1117DT18G DPAK

(Pb−Free)

NCP1117DT18RK DPAK

2500 / Tape & Reel

NCP1117DT18RKG DPAK

(Pb−Free)

NCP1117DT18T5 DPAK

NCP1117DT18T5G DPAK

(Pb−Free)

NCP1117ST18T3 SOT−223

4000 / Tape & Reel

NCP1117ST18T3G SOT−223

(Pb−Free)

NCP1117DT19RKG 1.9 DPAK

(Pb−Free)

2500 / Tape & Reel

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging

Specifications Brochure, BRD8011/D.

*NCV prefix is for automotive and other applications requiring site and control changes.

NCP1117, NCV1117

http://onsemi.com

ORDERING INFORMATION

Device Shipping†

PackageNominal Output Voltage

NCP1117DT20

2.0

DPAK

75 Units / Rail

NCP1117DT20G DPAK

(Pb−Free)

NCP1117DT20RK DPAK

2500 / Tape & Reel

NCP1117DT20RKG DPAK

(Pb−Free)

NCP1117ST20T3 SOT−223

4000 / Tape & Reel

NCP1117ST20T3G SOT−223

(Pb−Free)

NCP1117DT25

2.5

DPAK

75 Units / Rail

NCP1117DT25G DPAK

(Pb−Free)

NCP1117DT25RK DPAK

2500 / Tape & Reel

NCP1117DT25RKG DPAK

(Pb−Free)

NCP1117DT25T5 DPAK

NCP1117DT25T5G DPAK

(Pb−Free)

NCP1117ST25T3 SOT−223

4000 / Tape & Reel

NCP1117ST25T3G SOT−223

(Pb−Free)

NCP1117DT285

2.85

DPAK

75 Units / Rail

NCP1117DT285G DPAK

(Pb−Free)

NCP1117DT285RK DPAK

2500 / Tape & Reel

NCP1117DT285RKG DPAK

(Pb−Free)

NCP1117ST285T3 SOT−223

4000 / Tape & Reel

NCP1117ST285T3G SOT−223

(Pb−Free)

NCP1117DT33

3.3

DPAK

75 Units / Rail

NCP1117DT33G DPAK

(Pb−Free)

NCP1117DT33RK DPAK

2500 / Tape & Reel

NCP1117DT33RKG DPAK

(Pb−Free)

NCP1117DT33T5 DPAK

NCP1117DT33T5G DPAK

(Pb−Free)

NCP1117ST33T3 SOT−223

4000 / Tape & Reel

NCP1117ST33T3G SOT−223

(Pb−Free)

NCP1117DT50

5.0

DPAK

75 Units / Rail

NCP1117DT50G DPAK

(Pb−Free)

NCP1117DT50RK DPAK

2500 / Tape & Reel

NCP1117DT50RKG DPAK

(Pb−Free)

NCP1117ST50T3 SOT−223

4000 / Tape & Reel

NCP1117ST50T3G SOT−223

(Pb−Free)

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging

Specifications Brochure, BRD8011/D.

*NCV prefix is for automotive and other applications requiring site and control changes.

NCP1117, NCV1117

http://onsemi.com

ORDERING INFORMATION

Device Shipping†

PackageNominal Output Voltage

NCV1117DTARK*

Adjustable

DPAK

2500 / Tape & Reel

NCV1117DTARKG* DPAK

(Pb−Free)

NCV1117STAT3* SOT−223

4000 / Tape & Reel

NCV1117STAT3G* SOT−223

(Pb−Free)

NCV1117ST12T3*

SOT−223

NCV1117ST12T3G* SOT−223

(Pb−Free)

NCV1117DT15RK*

1.5

DPAK

2500 / Tape & Reel

NCV1117DT15RKG* DPAK

(Pb−Free)

NCV1117ST15T3* SOT−223

4000 / Tape & Reel

NCV1117ST15T3G* SOT−223

(Pb−Free)

NCV1117DT18RKG*

1.8

DPAK

(Pb−Free)

2500 / Tape & Reel

NCV1117DT18T5* DPAK

NCV1117DT18T5G* DPAK

(Pb−Free)

NCV1117ST18T3G* SOT−223

(Pb−Free) 4000 / Tape & Reel

NCV1117DT20RK*

2.0

DPAK

2500 / Tape & Reel

NCV1117DT20RKG* DPAK

(Pb−Free)

NCV1117ST20T3* SOT−223

4000 / Tape & Reel

NCV1117ST20T3G* SOT−223

(Pb−Free)

NCV1117DT25RK*

2.5

DPAK

2500 / Tape & Reel

NCV1117DT25RKG* DPAK

(Pb−Free)

NCV1117ST25T3* SOT−223

4000 / Tape & Reel

NCV1117ST25T3G* SOT−223

(Pb−Free)

NCV1117DT33T5*

3.3

DPAK

2500 / Tape & Reel

NCV1117DT33T5G* DPAK

(Pb−Free)

NCV1117ST33T3* SOT−223

4000 / Tape & Reel

NCV1117ST33T3G* SOT−223

(Pb−Free)

NCV1117DT50RK*

5.0

DPAK

2500 / Tape & Reel

NCV1117DT50RKG* DPAK

(Pb−Free)

NCV1117ST50T3G* SOT−223

(Pb−Free) 4000 / Tape & Reel

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging

Specifications Brochure, BRD8011/D.

*NCV prefix is for automotive and other applications requiring site and control changes.

NCP1117, NCV1117

http://onsemi.com

117AJG

ALYWW

17−15G

ALYWW

17−18G

ALYWW

117−2G

ALYWW

17−25G

ALYWW

17285G

ALYWW

17−33G

ALYWW

117−5G

ALYWW

17−12G

ALYWW

AYW

117−AG

SOT−223

ST SUFFIX

CASE 318H

A = Assembly Location

L = Wafer Lot

Y = Year

WW, W = Work Week

G or G = Pb−Free Package

MARKING DIAGRAMS − NCP PREFIX

DPAK

DT SUFFIX

CASE 369C

Adjustable 1.5 V 1.8 V 2.0 V 2.5 V

2.85 V 3.3 V 5.0 V 12 V

Adjustable 1.5 V 1.8 V 2.0 V 2.5 V

2.85 V 3.3 V 5.0 V 12 V

(Note: Microdot may be in either location)

AYW

17−15 G

123

AYW

17−18 G

123

AYW

117−2G

123

AYW

17−25 G

123

AYW

7−285 G

123

AYW

17−33 G

123

AYW

117−5G

123

AYW

17−12 G

123

1.9 V

AYW

17−19 G

123

17−19G

ALYWW

1.9 V

NCP1117, NCV1117

http://onsemi.com

17AJVG

ALYWW

1715VG

ALYWW

1718VG

ALYWW

1172VG

ALYWW

1725VG

ALYWW

1733VG

ALYWW

1175VG

ALYWW

AYW

117AV G

SOT−223

ST SUFFIX

CASE 318H

A = Assembly Location

L = Wafer Lot

Y = Year

WW, W = Work Week

G or G = Pb−Free Package

MARKING DIAGRAMS − NCV PREFIX

DPAK

DT SUFFIX

CASE 369C

Adjustable 1.5 V 2.0 V

2.5 V 3.3 V 12 V

Adjustable 1.5 V 1.8 V 2.0 V

2.5 V 3.3 V 5.0 V

(Note: Microdot may be in either location)

AYW

1715V G

123

AYW

1172V G

123

AYW

1725V G

123

AYW

1733V G

123

AYW

1712V G

123

1.8 V

AYW

1718V G

123

NCP1117, NCV1117

http://onsemi.com

PACKAGE DIMENSIONS

SOT−223

ST SUFFIX

CASE 318H

ISSUE O

ÉÉÉ

NOTES:

1. DIMENSIONS ARE IN MILLIMETERS.

2. INTERPRET DIMENSIONS AND TOLERANCES

PER ASME Y14.5M, 1994.

3. DIMENSION E1 DOES NOT INCLUDE INTERLEAD

FLASH OR PROTRUSION. INTERLEAD FLASH OR

PROTRUSION SHALL NOT EXCEED 0.23 PER

SIDE.

4. DIMENSIONS b AND b2 DO NOT INCLUDE

DAMBAR PROTRUSION. ALLOWABLE DAMBAR

PROTRUSION SHALL BE 0.08 TOTAL IN EXCESS

OF THE b AND b2 DIMENSIONS AT MAXIMUM

MATERIAL CONDITION.

5. TERMINAL NUMBERS ARE SHOWN FOR

REFERENCE ONLY.

6. DIMENSIONS D AND E1 ARE TO BE DETERMINED

AT DATUM PLANE H.

DIM MIN MAX

MILLIMETERS

A--- 1.80

A1 0.02 0.11

b0.60 0.88

b1 0.60 0.80

b2 2.90 3.10

b3 2.90 3.05

c0.24 0.35

c1 0.24 0.30

D6.30 6.70

E6.70 7.30

E1 3.30 3.70

e2.30

e1 4.60

L0.25 ---

T0 10

0.2 C C

0.1 C S

E1 B

0.1 C S

0.08

(b)

(b2)

SECTION B−BL

ÇÇÇ

ÉÉÉÉÉÉÉ

ÇÇÇÇÇÇÇ

SECTION A−A

1.5

0.059 ǒmm

inchesǓ

SCALE 6:1

3.8

0.15

2.0

0.079

6.3

0.248

2.3

0.091

2.3

0.091

2.0

0.079

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

NCP1117, NCV1117

http://onsemi.com

PACKAGE DIMENSIONS

DPAK

DT SUFFIX

CASE 369C

ISSUE D

0.005 (0.13) C

DIM MIN MAX MIN MAX

MILLIMETERSINCHES

D0.235 0.245 5.97 6.22

E0.250 0.265 6.35 6.73

A0.086 0.094 2.18 2.38

b0.025 0.035 0.63 0.89

c2 0.018 0.024 0.46 0.61

b2 0.030 0.045 0.76 1.14

c0.018 0.024 0.46 0.61

e0.090 BSC 2.29 BSC

b3 0.180 0.215 4.57 5.46

L4 −−− 0.040 −−− 1.01

L0.055 0.070 1.40 1.78

L3 0.035 0.050 0.89 1.27

Z0.155 −−− 3.93 −−−

NOTES:

1. DIMENSIONING AND TOLERANCING PER ASME

Y14.5M, 1994.

2. CONTROLLING DIMENSION: INCHES.

3. THERMAL PAD CONTOUR OPTIONAL WITHIN DI-

MENSIONS b3, L3 and Z.

4. DIMENSIONS D AND E DO NOT INCLUDE MOLD

FLASH, PROTRUSIONS, OR BURRS. MOLD

FLASH, PROTRUSIONS, OR GATE BURRS SHALL

NOT EXCEED 0.006 INCHES PER SIDE.

5. DIMENSIONS D AND E ARE DETERMINED AT THE

OUTERMOST EXTREMES OF THE PLASTIC BODY.

6. DATUMS A AND B ARE DETERMINED AT DATUM

PLANE H.

12 3

5.80

0.228

2.58

0.102

1.60

0.063

6.20

0.244

3.00

0.118

6.17

0.243

ǒmm

inchesǓ

SCALE 3:1

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

H0.370 0.410 9.40 10.41

A1 0.000 0.005 0.00 0.13

L1 0.108 REF 2.74 REF

L2 0.020 BSC 0.51 BSC

DETAIL A

SEATING

PLANE

L2 GAUGE

PLANE

DETAIL A

ROTATED 90 CW5

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice

to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All

operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights

nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications

intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should

Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,

and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death

associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal

Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

NCP1117/D

PUBLICATION ORDERING INFORMATION

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81−3−5817−1050

LITERATURE FULFILLMENT:

Literature Distribution Center for ON Semiconductor

P.O. Box 5163, Denver, Colorado 80217 USA

Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada

Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

For additional information, please contact your local

Sales Representative