SUMICON 1600 SERIES RECTANGULAR CONNECTORS [the SUMICON 1600 series are multi-contact connec- tors designed by Hirose. 8, 12, 16, 20, 24, 28, 34, 45 and 60-contact models available (same as the 1300 series). The connector units are available in three types: soldering, wrapping, and crimping. Accessories Standard Type General In the SUMICON 1600 series, the connector unit is completely separated from the accessories such as the cases and stoppers to diversify the specifications and Material and Finish are C case, CA case, CBA case, ST stopper, STA stop-\\ per, and STB stopper. By combining the many options noted above, the SUMICON 1600 series connectors meet a wide variety of applications. facilitate wiring connection. The SUMICON 1600 series are specified in the NTT specifications No.1931. Ordering Information Electrical Characteristics Part Material Finish Glass filled Item Standard Insulator diallylphthalate resin Blue Contact 7mQ or less : . Civare Resistance at DC1A Male Terminal Brass Type A: Silver-plated Insulation 4000M Q or mote Female Terminal Phosphor bronze Type B: Gold-plated Resistance at DC500V . j Plug Case ABS resin (black) NTT spec: ABS resin, Withstand 2.5PB 6.0/2.0 (color) AC1000V for 1 minute Voltage Treatment with chromate Stopper Bracket Steel over zinc platin Current Rating 3A P g Voltage Rating AC300V Wire Wrapping Specifications AWG 26 28 30 Applicable Applicable 0.41 0.32 0.26 wire wire (mm) Max.coating 0.D.(mm) 0.95 0.75 0.6 . Ordinary Coating Coating Wrapping method wrapping one wrap one wrap Effective number of wrappings about 8 about 8 about 9 Number of wrappings 2 wrap per terminal PW-16 34 (1) (2) (3) (4) (1) Shape of terminal opening P: Male terminal S: Female terminal (2) Terminal connection method No sign: Soldering W: Wrapping C: Crimp (8) Series No. 16: 1600 series (4) Number of contacts 34: 34 contacts (5) Serial sign for connector units Provided with a sequence of upper-case alphabetic charac- ters. No sign or sign other than W: Soldering Sequence: No sign, B,C,D,E ... (6) Plating A: Silver-plated B: Gold-plated (7) Signs for accessories I C: Plug case oAaA-c Oo Q (5) (6) (7) (8) (9) ST: Stopper bracket with horizontal cable inlet opening J: Jack Case H: Handle DB: Deep bracket (8) Serial signs for accessories Each accessory (C,ST,J,H,DB) is provided with sequence of upper-case alphabetic characters. Sequence: No sign, A,B,C... Accessories, C,ST, or J followed by no sign: Side lock types Accessories, C and ST followed By A: Top touch lock type Note: The space for no sign is filled sequentially. (9) Special specification number For a special specification, ( ) is filled with a serial number, except for the case and bracket, for which the following ap- (01): Bracket only (20): Case only : JCross Reference to NTT No. ( Type NTT No. Short Form HRS No. Part No. Type NTT No. Short Form HRS No. Part No. CN-3320GLWPMSA; 20GLWPMSA |CL216-0247-5-01| P-1620BA-CA(01) CN-5445GJMSA 45GJMSA CL216-0257-9-01 | P-1645BA-STA(01) CN-4028GLWPMSA| 28GLWPMSA GL216-0249-0-01| P-1628BA-CA(01) CN-6760GJMSA 60GJMSA CL216-0258-1-01 | P-1660BA-STA(01) CN-4534GLWPMSA| 34GLWPMSA /|CL216-0250-0-01| P-1634BA-CA(01) CN-3320G2JMSA 20G2JMSA |CL216-0292-0-01 IPW-1620BA-STA(01)} CN-~5S445GLWPMSA; 45GLWPMSA |CL216-0251-2-01} P-1645BA-CA(01) CN-3724G2JMSA 24G2JMSA_ |CL216-0293-2-01 IPW-1624BA-STA(01) CN-6760GLWPMSA| 60GLWPMSA |GL216-0252-5-01| P-i660BA-CA(01) GN~4028G2JMSA 28G2JMSA | CL216-0294-5-01 [PW-1628BA-STA(01}} Plug CN-3320GLWPFSA| 20GLWPFSA |CL216-0153-3-01] S-1620A-CA(01) CN~4534G2JMSA 34G2JMSA |CL216-0296-0-01 | PW-1634A~STA(01) CN-3724GLWPFSA| 24GLWPFSA |CL216-0154-6-01| S-1624A-CA(01) CN~-6760G2JMSA 60G2JMSA |CL216-0298-6-01 |PW-1660BA-STA(01}} Receptacle CN-4028GLWPFSA| 28GLWPFSA |CL216-0155-9-01| S-1628A-CA(01) CN-3320GJFSA 20GJFSA CL216-0151-8-01} S-1620A-STA(01} CN-4534GLWPFSA| 34GLWPFSA |CL216-0126-0-01| S-1634A-CA(01) CN-3724GJFSA 24GJFSA CL216-0148-3-01| S-1624A-STA(01) CN-5445GLWPFSA| 45GLWPFSA |CL216-0127-3-01| S-1645A-CA(01) CN~-4028GJFSA 28GJFSA CL216-0152-0-01) S-1628A-STA(01) CN-6760GLWPFSA| 60GLWPFSA |CL216-0128-6-01] S-1660A-CA(01} CN~4028G2JFSA 28G2UFSA CL216-0313-8-01 | SW~1628A-STA(01) ( , CN-3724GJMSA 24GJMSA CL216-0254-0-01| P-1624BA-STA(01} CN-4634G2JFSA 34G2JFSA CL216-0299-9~01 | SW-1634A~STA(01) Receptacle | CN-4028GJMSA 28GJMSA CL216-0255~3-01| P-1628BA-STA(01) CN-5445G2JFSA 45G2JUFSA CL216-0300-6-01 | SW-1645A-STA(01) CN-4534GJMSA 34GJMSA CL216~0256-6-01| P-1634BA-STA(01) GN-6760G2JFSA 60G2JFSA CL216-0301-9-01 | SW-1660A-STA(01) Note: NTT Types are all assembled with connector inserts and piug shells or stopper brackets. fo 112CL216-0177-1 P-1634BA ee Solder Hole No. of| A Type G Type Pins HRS No. Part No. HRS No. Part No. 8 * CL216-0171-5-09 P-1608BA(09) *CL216-0180-6-09 P-1608BG(09) 25 12 * CL216-0172-8-09 P-1612BA(09) * CL216-0181-9-09 P-1612BG(09) 30 16 * CL216-0173-0-09 P-1616BA(09) * CL216-0182-1-09 P~1616BG(09) 35 20 * CL216-0174-3-09 P-1620BA(09) * CL216-0183~4-09 P~1620BG(09) 33 11 24 * CL216-0175-6-09 P-1624BA(09) * CL216-0184-7-09 P-1624BG(09) 37 11 28 * CL216-0176-9-09 P-1628BA(09) * CL216-0185-0-09 P-1628BG(09) 40 11 34 * CL216-0177-1-09 P-1634BA(09) * CL216-0186-2-09 P-1634BG(09) 45 11 45 * CL216-0178-4-09 P~1645BA(09) * CL216-0187-5-09 P-1645BG(09) 54 11 60 * CL216-0179-7-09 P-1660BA(09) * CL216-0188-8-09 P-1660BG(09) 67 11 *: Standard ( Female Connector CL216-0007-1 S-1634A Solder Hole be tr | Unit: mm No.of A Type G Type Pin HRS No. Part No. HRS No. Part No. 8 * CL216-0001-5-09 S-1608A(09) * CL216-0055-4-09 S~1608G(09) 25 12 * CL216-0002-8-09 S-1612A(09) * CL216-0056-7-09 $-1612G(09) 30 16 * CL216-0003-0-09 S$-1616A(09) * CL216-0057-0-09 $-1616G(09) 35 20 * CL216-0004-3-09 S-1620A(09) * CL216-0058-2-09 S-1620G(09) 33 VW 24 * CL216-0005-6-09 S~1624A(09) * CL216-0059-5-09 $-1624G(09) 37 11 28 * CL216-0006-9-09 S-1628A(09) %* CL216-0060-4-09 S-1628G(09) 40 11 34 * CL216-0007-1-09 S$-1634A(09) * CL216-0061-7-09 $-1634G(09) 45 11 45 * CL216-0008-4-09 S-1645A(09) * CL216-0062-0-09 $-1645G(09) 54 11 60 * CL216-0009-7-09 S-1660A(09) * CL216-0063-2-09 $~1660G(09) 67 11 %*: Standard 113Wire Wrapping Pin Connector (hale connector oo 4.5 6 be 2-2.99 4.5 b-3.5 }+_D f a i LS he Wrap Post 0.50.7 14.2 Unit: mm Type A Type G No.of Ails|iclole Pin HRS No. Part No. HRS No. Part No. 8 *CL216-0198-1-09 | PW-1608BA(09) | CL216-0216-1-09 | PW-1608BG(09) | 25] 19 | 10} 13] 8 CL216-0204-2 12 | %*GL216-0199-4-09 | PW-1612BA(09) | CL216-0217-4-09 | PW-1612Ba(09) | 30] 24| 10] 18] 8 ( PW-1634BA 16 | *CL216-0200-1-09 | PW-1616BA(09) | CL216-0218-7-09 | PW-1616BG(09) | 35 | 29 | 10 | 23] 8 20 %* CL216-0201-4-09 PW-1620BA(09) | CL216-0219-0-09 | PW~-1620BG(09) | 33 | 27 | 13 | 21 | 11 24 * CL216-0202-7-09 PW-1624BA(09) | CL216-0220-9-09 | PW-1624BG(09) | 37 | 31 | 13 | 26 | 11 28 * CL216-0203-0-09 PW-1628BA(09) | CL216-0221-1-09 | PW-1628BG(09) | 40 | 34 | 13 | 28] 11 34 * CL216-0204-2-09 PW-1634BA(D9) | CL216-0222-4-09 | PW-1634BG(09} | 45 | 39 | 13 | 33 | 11 45 * CL216-0205-5-09 PW-1645BA(09) | CL216-0223-7-09 | PW-1645BG(09) | 54 | 48 | 13 | 42 | 11 60 * CL216-0206-8-09 PW-1660BA(09) | CL216-0224-0-09 | PW~1660BG(09) | 67 | 61 | 13 | 58 | 11 \ *; Standard ( remate connector \ | | ( Wrap Post 0.5x0.7 Unit; mm Type A Type G No.of alelelole a HRS No. Part No. HRS No. Part No. 8 *CL216-0189-0-09 | SW-1608A(09) | CL216-0207-0-09 | SwW-1608G(09) | 25] 19] 10| 13] 8 12 %* GL216-0190-0-09 SW-1612A(09) CL216-0208-3-09 SW-1612G(09) 30 | 24] 10) 18) 8 CL216-0195-3 SW-1634A 16 * CL216-0191~2-09 SW-1616A(09) GL216-0209-6-09 SW~-1616G(09) 35 | 29/10] 23] 8 20 * CL216-0192-5-09 SW-1620A(09) CL216-0210-5-09 SW-1620G(09) | 33 | 27 | 13 | 21.111 24 * CL216-0193-8-09 SW-~1624A(09} CL216~0211-8-09 SW-1624G(09) | 37 | 31 | 13 | 26 | 11 28 * CL216-0194-0-09 SW-1628A(09) CL216-0212-0-09 SW-1628G(09) | 40 | 34 | 13 | 28 | 11 7 34 * CL216-0195-3-09 SW-1634A(09) CL216-0213-3-09 SW-1634G(09) | 45 | 39 | 13 | 33 | 14 ( 45 * CL216-0196-6-09 SW-~-1645A(09) CL216-0214-6-09 SW-1645G(09) | 54) 48 | 13 | 42 | 11 60 %* GL216-0197-9-09 SW-1660A(09) CL216~0215-9-09 SW-1660G(09) | 67 | 61 | 13] 55] 11 *; Standard SD 114Side Touch Lock Type Plug Shell CL216-00344-20 P-1634A-C(20) NN Side Touch ~ CL216-0052-6-01 P-1634A-ST(01) a O a p Loo | ( [ | ) = 4 { }=-"7}. Unit: mm No.of Pin HRS No. Part No. AB C/D;)/E!]FiIG{H * CL216-0028-1-20 P-1608A-C(20)| 29 | 20 14.5 42 |7.5 12.5] 12.5 12 * CL216-0029-4-20 P~1612A-C(20)| 34 | 20 14.5}43 517.5] 9 13.5] 13.5 16 * CL216-0030-3-20 P-1616A-C(20)| 39 | 20 14.5 46 | 7.5 11.5)14.5:14.5 20 * CL216-0031-6-20 P-1620A-C(20)| 37 | 23 17.5] 45. -O| 11 | 11 14.5] 14.5 24 * CL216-0032-9-20 P-1624A-C(20)| 41 | 23 17.5} 46. 5] 11] 12; 15] 156 28 * CL216-0033-1-20 P-1628A-C(20)| 44 | 23 17.5) 47. -5{ 11) 13 15.5} 15.5 34 * CL216-0034-4-20 P-1634A-C(20)| 49 | 23 17.5|50. 5} 11 | 16 | 17 | 17 45 * CL216-0035-7-20 P-1645A-C(20)| 58 | 23 18.5 54.5, 11 | 19 18.5] 19.5 60 * CL216-0036-0-20 P-1660A~C(20)| 71 | 23 18.5] 59. 5] 11 | 24 | 21 | 22 Note: All these products are plug cases only. Order connector units separately. The cases can be used for both male and female connector units. cases marked with an asterisk ar of standard specifications. A Lock Type Receptacle Bracket B D The *: Standard | 1 J Chr: . + ea 2-M2.6x 0.4510 8.5 Unit: mm NooF HRS No. Part No. aAlspic|pje 8 | *CL216-0046-3-01| P-1608A-ST(01) | 27 | 19 |13.6| 9.2 |15.5 12 | *CL216-0047-6-01} P-1612A-ST(O1) | 32 | 24 | 13.6] 9.2 | 15.5 16 | *CL216-0048-9-01; P-1616A-ST(01) | 37 | 29 |13.6! 11 [15.5 20 | *CL216-0049-1-01| P-1620A-ST(01) | 35 | 27 116.6] 11 118.5 24 | *CL216-0050-0-01| P-1624A-ST(01) | 39 | 31 116.6] 11 /18.5 28 | *CL216-0051-3-01| P-1628A-ST(01) | 42 | 34 [16.6] 11 |18.5 34 | *CL216-0052-6-01| P-1634A-ST(01) | 47 | 39 |16.6 1118.5 45 | *CL216-0053-9-01} P-1645A-ST(01) | 56 | 48 |16.6/ 15 118.5 60 | *CL216-0054-1-01| P-1660A-ST(O1) | 69 | 61 /16.6! 15 |18.5 Note: All these products are stopper brackets only. Order connector units separately. The cases can be used for both male and female con- nector units. The brackets marked with an asterisk are of standard specifications. *: StandardTop Touch Lock Type Plug Shell A hata Soot B + o le 2 Ly o oo _ 4 o Cc aw So mM gg Vv CL216-0111-3-20 P-1634A-CA(20) Unit: mm Noot HRS No. Part No. Ala ilc|pol]el]e|e 20 * CL216-0149-6-20 P-1620A-CA(20) 37 | 20 | 61 | 11 |] 11 | 18 | 146 24 * CL216-0147-0-20 P~1624A-CA(20) 41 | 20 | 51 | 11 | 12 | 18.5] 15 28 %* CL216-0150-5-20 P-1628A-CA(20) 44} 20 | 53 |] 11 | 13 | 20 | 155 34 * CL216-0111-3-20 P-1634A-CA(20) 49 | 20 | 56 | 11 | 16 | 21.6] 17 45 * CL216-0112-6-20 P-1645A-CA(20) 58 | 20 | 60 | 11 | 19 | 24 | 185 60 * CL216-0113-9-20 P-14660A-CA(20) 71 | 20 | 65 | 11 | 24 | 26.5} 21 Note: All these products are Plug cases only. Order connector units separately. The cases can be used for both male and female connector units. The cases marked with an asterisk are of standard specifications. * Standard Top Touch Lock Type Stopper Bracket Koa) LS rr CL216-0123-2-01 P-1634A-STA (01) 116 15.7 9.7 2 M2.6x0.45x10_/ Unit: mm No.0 HRS No. Part No. A|B 20 *.CL216-0156-1-01 P-1620A-STA(01) | 33 | 27 24 %* CL216-0157-4-01 P-1624A-STA(O1) = 137) 31 28 %* CL216-0158-7-01 P-1628A-STA(01) | 40 | 34 34 * CL216-0123-2-01 P-1634A-STA(01) | 45] 39 45 * CL216-0124-5-01 P-1645A-STA(O1) | 54| 48 60 * CL216-0125-8-01 P-1660A-STA(O1) |67| 61 Note: Ali these products are stopper brackets only. Order connector units separately. The cases can be used for both male and female connec- tor units. The brackets marked with an asterisk are of standard specifications. %: StandardSide Touch Lock Type Jack Shell (For Extension Cable) XN Top Touch Lock Type Stopper Bracket CL216-0142-7-20 $-1634A-J (20) foal a [oo] 1 ] cq Unit: mm Not HRS No. Part No. aAlspijcilojelrlel x 20 | CL216-0139-2-20 | s-1620A-u(20) | 37 | 23 [17.slassl 11 | 11 [1451145 24 | CL216-0140-1-20 | s-1624A-u(20) | 41 | 23 lizslaes| 41] 12 118 [15 28 | cL216-0141-4-20 | _s-1628A-u(20) | 44 | 23 |17.5/47.5] 11 | 13 [165/155 34 | CL216-0142-7-20 | s-1634A-u(20) | 49 | 23 |17.5/50.5| 111 16 |17 |17 45 | CL216-0225-2-20 | _s-1645A-u(20) | 58 | 23 [185/546 11 | 19 [185/195 60 | CL216-0226-5-20 | s-1660A-u(20) | 71 | 23 [1asls05! 11 | 24 [21 122 Note: All these products are jack cases only. cases can be used for female connector units only. Order connector units separately. The CL216-0325-7 1645STA-DC ( g J fo, sg A wera el Unit: mm No.of HRS No. Part No. A Pin 20 | CL216-0321-6 1620STA-DC | 38.3 24 | CL216-0322-9 16248TA-DC | 42.3 28 | CL216-0323-1 4628STA-DC | 45.3 34 | CL216-0324-4 1634STA-DC | 50.3 45 | CL216-0325-7 16458TA-DC | 59.3 60 | CL216-0326-0 4660STA-DC | 72.3 117SHOULDER-TOUCH LOCK TYPE General The shoulder-touch lock type plug cases are highly re- packaging plug cases, including the top-touch lock liable, lightweight, sturdy, and operable. 8,12,and_ type, are available in 8 to 60-contact models. 16-contact models are available. Hirose high-density Material and Finish Description Material Finish Plug case Polypropylene resin Black St Steel Treated with chromate opper ee over zinc plating Plug Shell ( ) ~Y (OT CX c} B Unit: mm No.of HRS No. Part No. alsp|c!oplelr CL216-0418-6 pin 1616-CBA 8 | *CL216-0416-0 1608-CBA 14 | 35 | 40 | 45 7.5 > 12 | *CL216-0417-3-01| 1612-CBA(01) 14 | 40 | 41 46 9 7.5 16 | *CL216-0418-6 1616-CBA 14 | 45 | 42 | 47 | 11.51) 7.5 *: Standard Note: Order connector units separately. The cases can be used for both male and female connector units. The cases marked with an asterisk are of standard specifications. How to Mount Connector Unit Stopper M2.6 Screw 2.76 76 HRS No. Part No. Remark CL216-0302-1 *CL216-0302-1 | 1600-STB | Common for any size 1600-STB * : Standard . Note: Order connector units separately. The cases Note: Mounted on a connector unit marked with an asterisk are of standard speci- (Each package contains two stoppers) fications. 1181600 SUMICON CRIMP TYPE CONNECTORS General r The SUMICON 1600 series are high-performance compact crimp type connectors developed for labor saving in connection work. 8, 12, 16, 20, 24, 34, 45 and 60- contact models are available. All models are compatible with our previous top-lock type plug cases. For using the connectors separately, easy-to-mount plastic locks are available to expand their functions. NY Electrical and Environmental Characteristics Material and Finish ~ r Item Standard Part Material Finish Contact Resistance 7mQ or less at DC 1A (contact only) Glass~containing Insulator . Biue Insulatio polycarbonate resin UL94V-0 nsulation Resistance 5,000MQ or more at DC 500V Male Brass Gold-plated . ; Terminal Silver- plated Withstand Voltage AC 1,000V for 1minute - Female Gold-plated Rating Current 3A Terminal Phosphor bronze Sllver-plated Applicable Cable AWG # 24-28 (Coating O.D. 1.6 $-0.99) Cable AWG #24 AWG # 26 AWG # 28 Crimping strength - (Unit: kg or more) | Crimping 36 24 16 force . / . . K Features / (1) Since this is a press-fit type connector, anyone can perform wiring securely with high reliability. (2) For contact, a two-point contact system is em- ployed for outstanding reliability, It aslso offers su- perior mechanical strength. (3) The Sumicon 1600 Series Press-Fit Type Connec- tors are interchangeable with the conventional sol- der, DIP and tapping type connectors. They are applicable, therfore, to a wider range of applica- tions. (4) (5) To use the connector unit separately, jointly em- ploying an easily installable plastic lock will pre- vent vibrations and/or cable dead weight from un- plugging the connector. The plastic lock, moreov- er, can be used with either center-suspension or panel-mount system. All wiring spliced with the connector is hidden completely inside the housing, allowing for perfect insulation. 120Housing ht 2-2.9 P h 19.5 Unit: mm Unit: mm HRS No. Noo! Part No. Lleplw HRS No. No-ofl part No. L|plw | CL216-0335-0 | 8 Pc-1608 | 25 | 19 | 10 *| CL216-0344-1 | 8 sc-1608 | 25 | 19 | 10 | cL216-033e-3 | 12 | Ppc-1e12 | 30 | 24 | 10 | cl2ie-0345-4 | 12 | sc-1e12 | 30 | 24 | 10 | cL216-0337-6 | 16 | pc-te1e | 35 | 29 | 10 | cL216-0346-7 | 16 | sc-tere | 35 | 29 | 10 | cL216-0338-9 | 20 | pc-1e20 | 33 | 27 | 13 | cL216-0347-0 | 20 | sc-1e20 | 33 | 27 | 13 | cL2te-0330-1 | 24 | Ppo-te24 | 37 | 31 | 13 | cL2ie-os4s-2 | 24 | sc-1624 | 37 | 31 | 13 *| cLete-o340-0 | 28 | Pco-te28 | 40 | 34 | 13 | cLete-oa49-5 | 28 | sc-t628 | 40 | 34 | 13 *| cL2te-0341-3 | 34 | Pc-1634 | 48 | 39 | 13 | cL216-0350-4 | 34 | sc-1634 | 45 | 99 | 13 | cL2ie-0342-6 | 45 | po-te4s | 54 | 48 | 13 | oL216-0351-7 | 45 | sc-16e45 | 54 | 48 | 13 *! cL216-0343-9 | 60 | Pc-te60 | 67 | 61 | 13 | cL216-0352-0 | 60 | sc-16e60 | 67 | 61 | 13 \ *: Standard *: Standard / Contact {Pin Connector Socket Connector 17.5 | | 17.5 | Type HRS No. Part No. Plating Type HRS No. Part No. Plating * CL216-0331-0 PC~-1600-111 Gold * CL216-0333~5 SC~1600-1114 Gold Loose Loose * CL216-0332-2 PC-1600-112 Silver * CL216-0334-8 SC-1600-112 Silver CL216-0363-6 PC~1600-211 Gold * CL216-0365-1 SC-1600-211 Gold Chain Chain * CL216-0364-9 PC-1600-212 Silver * CL216-0366-4 SC-1600-212 Silver *: Standard *: Standard Note: Loose-piece terminals are available in packs. Each pack contains 100 terminals. Strip terminals are available in reels. Each reel contains 10,000 terminals. 121Tools NY Type HRS No. Part No. Manual crimping tool CL250-0003-1 TC-1600-111 Contact extractor CL250-0004-4 TC-1600-21 Hand Crimp Tool TC-16001111 Ordering Information Contact Extractor TC160021 yy Ne @ Housing No.of Pin Series No. Crimp type P:Male, S:Felmale Using the Connectors Contact 1: Gold-plated 2: Silver-plated Applicable cable 1: AWG # 24-28 1: Loose piece contact 2: Strip contact Series No. Crimp type P: Male contact S: Female contact] f (1) (2) (3) 122 Take care when removing the connectors to pull out by the housing and not tug on the wires. The male terminals of the connectors will be bent if the connectors are twisted when being removed. Take care to pull the characters out straight. The plastic locks are sufficiently strong to ensure that the connector engagement will not be loosened by vibration or the weight of the wires. Their strength is not sufficient for other loads. When strength for some other load is required, use the top-touch lock type plug case (common for both solder and wrapping types). ~ (4) Both gold-plated and silver-plated terminals are available. Use the gold-plated type in adverse en- vironments. In other environments. we recommend the economical silver-plated type. (5) For crimping, use a manual crimping device for low-volume crimping and maintenance. For high- volume crimping. we recommend the automatic crimping machine shown on page 124. (6) For plug-in uses, we recommend Sumicon 1600 series solder or wrapping types for improved func- tionality. SAssembling Procedure cr Ne Pin contact oe vs) Socket contact ee Crimped state Procedure for Contact Extraction 4 ~ Pin contact housing Low-numbered side After assembling, pull the wire slightly and make sure if the con- tact is mounted as shown above. Socket contact housing J (, case of extracting a contact from the housing due to insertion error or circuit change, foliow the steps as shown below. Fig. 1 Extraction rt Oe Shell > N Hold the Contact Extractor as shown in Fig.1, plac- ing the tip of the Extractor on the tip of a contact, then insert it between the contact and the housing. When the tip of the Extractor comes into contact with a stepped part in the housing, the spring will come off from the stepped part with a snap which can be felt. Then, extract the contact by pulling the wire. ~ (Caution: Pushing the tip of the extractor forcibly before the spring has come off from the stepped part may damage the contact). Above Fig.1 and Fig.2 show how to extract a con- tact from socket housing. The same procedure can be employed to extract a contact from pin housing. 123Hints on Use of Connectors with Respect to Polarity (to prevent mis-insertion of connectors) ( ctarization of SUMICON 1600 series can be achieved by contact arrangement. The crimp type contacts are designed to float a little, so that the use of a Polarizing In Case of 8,12 and 16 pin 1. When crimp types are used in both the male and female, do noi fill all cavities with contacts. Use Polarizing Key at minimum 2 cavities of Socket housing as shown below and do not fill pin con- tacts at the corresponding cavities of male hous- ing. 1. SUMICON 1600 series are naturally polarized in all cavities filled with contacts. When all cavities are not filled, Polarizing Keys shall be inserted in vacant cavities to the minimum for preventing reverse coupling. But when Top Touch Lock Plug Shell is used, Polarizing Keys are not necessary 124 2. When male crimp type is used in combination with In Case of Multi Pin Type more than 20 pin 2. When male crimp type is used with some vacant Key is recommended in order to ensure positive nota ization. solder or wire wrap female type, the connector coupling shall be done corefully not to couple in reverse position. Coupling shall be made by matching of traiangle marks on connector inserts. because Plug Shell has polarized mechanism. cavities in combination with solder or wire wrap female type, Top Touch Lock Plug Shell is recom- mended.~ y, ~ Handle Unit: mm No.of HRS No. PartNo. |A|B |C]D Pin + 16 | CL216-0135-1 | 1616-H | 36| 25] 6 | 29 be oiote-0196-4 meen 34 | CL216-0136-4 | 1634-H_ | 46/30 | 6 | 39 ED: 694-H KR Hy 60 | CL216-0137-7 | 1660-H | 68| 30] 8 | 61 Deep Bracket 68: 12.8 Unit: mm $ F No-of | HRS No. Part No. , i b+} (> 4 . 34 | CL216-0138-0 | 1634-DB CL216-0138-0 fa-3a6 1634-DB Crimp or any Connector Unit How to Mount HRS No. Part No. Molding * CL216-0354-5 1600-LC fo *: Standard . Common for solder, wire wrap, 1600LC crimp or any connector unit Polarizing Key HRS No. Part No. How to Mount * CL216-0487-9 Polarizing Key %* : Standard Polarizing Key Molding this manual. Le : N The polarizing key (material: SC-16 any type of female housing. For handling, see connector polarity (prevention of misinsertion on 124page of ") can be used for Notes on 125Terminal Arrangment and Numbers r \ The figure shows a male connector as viewed from the termination side \ ) Connector Mounting Hole Dimensions ( > Unit: mm No.of A B c screw Pin 8 | 19 |135] a5 7A 12 | 24 |185| 385 ____-__ p______ 16 | 20 | 235] 85 20 | 27 [215/115 } 24 | 31 | 255| 11.5 M2.6 c 28 | 34 | 2851 11.5 { 34 | 39 | 335/115 23 45 | 48 | 425/115 60 | 61 |555| 115 126SUMICON 1600 SERIES DIP SOLDERING CONNECTORS General (~ Y\ The SUMICON 1600 series are original Hirose rec- tangular dip soldering connectors 8,12,16,20,24,34,45 and 60-contact models are available. All models are compatible with the previous 1600 series in mounting and accessories. Ne S Features Allows straight dip soldering onto a PCB, and is 3. effective in PCB-to-PCB and PCB-to-cable con- nection. 4. Suitable for use in interfaces, being compact -and lightweight and meeting high-density packaging requirements. Main Applications Computers, peripherals and terminals, data com- munications equipment, measuring instruments, Further cuts interconnection costs when simple locks are used. A wide variety of combinations of connection methods availabie, e.g., dip soldering, wrapping, and crimping, to meet your requirements. signal equipment, mobile radio equipment, copier and FAX machine. LY KEY Electrical and Environmental Material and Finish Glass-Filled diatlylphtalate resin Brass Type A: Silver-plated Phosphor bronze Type B: Gold-plated Performance Contact 7mQ or less at DC 1A Insulator Resistance Male Terminal Insulation 1,000M or higher ; Resistance at DC 500V Female Terminal Withstand AC 1,000V for 1 minute Voltage Current capacity 3A Ordering Information 16 34 ( o (4) Number of contacts (5) Serial sign for connector units Provided with sequence of upper-case alphabetic characters. OA I | (1) (2) (3) (4) (5) (6) (7) (8) (1) Shape of terminal opening Sequence: No sign, B,C,D,E... P: Male terminal (6) Plating S: Female terminal A: Silver plated (2). Terminal connection method B: Gold plated D: Dip soldering (7) Signs for accessories (3) Series No. SP: Spacer for dip soldering 16: 1600 series (8) Serial signs for accessories SP 0 tl J / Each accessory is provided with a sequence A of upper-case alphabetic characters. Sequence: No sign, A,B.,... yy, 127Dip Soldering Type Connector (Male Connector me ( { Dip Post 0.50.5 D @| i 4 2-2.9 7.2 - Unit: mm Type A Type G Not aAlepic|ole a HRS No. Part No. HRS No. Part No. 8 * GL216-0388-7-09 PD-1608BA(09) CL216-0406-7-09 PD-1608BG(09) | 26/719 | 10]13] 8 42 %* CL216-0389-0-09 PD-1612BA(09) GL216-0407-0-09 PD-1612BG(09) | 30] 24/10/18] 8 ( 16 %* CL216-0390-9-09 PD-1616BA(09) GL216-0408-2-09 PD-1616BG(09) | 35 | 29] 10 | 23] 8 20 % CL216-0391~1-09 PD-1620BA(09)} CL216-0409-5-09 PD-1620BG(09) | 33 | 27] 13 | 21} 11 24 %* CL216-0392-4-09 PD-1624BA(09) CL216-0410-4-09 PD-1624BG(09) | 37 | 31 | 13 | 25 | 11 CL216-0394-0 28 * CL216-0393-7-09 PD-1628BA(09) CL216-0411-7-09 PD-1628BG(09) | 40 | 34 | 13 | 28 | 11 PD-1634BA 34 * CL216-0394-0-09 PD-1634BA(09) CL216-0412-0-09 PD-1634BG(09) | 45} 39 | 13 | 33 | 11 45 #* CL216-0395-2-09 PD-1645BA(09) CL216-0413-2-09 PD-1645BG(09) | 54 | 48 | 13 | 42 | 11 60 %* CL216-0396-5-09 PD-1660BA(09) CL216-0414-5-09 PD-1660B8G(09) | 67 | 61 | 13 | 56 | 11 * \ Standard S) (" cemale Connector Dip Post 0.50.5 bag A. ~ 8 B 7] 3.5 D c | ( Tat | cs (6) e| [I @| = Lat Pt i Th 4 2-2.9 ol Unit: mm Type A Type G No.of ype yee ajelclole Pin HRS No. Part No. HRS No. Part No. 8 % CL216-0379~6-09 SD~1608A(09) CL216-0397-8-09 SD-1608G(09) 26119] 10/13 | 8 12 * CL216-0380-5-09 SD-1612A(09) CL216-0398-0-09 $D-1612G(09) 30 | 24] 10] 18} 8 16 * CL216-0381-8-09 SD-1616A(09) CL216-0399-3~09 SD-1616G(09) 35 | 29 | 10] 23) 8 20 * CL216-0382-0-09 SD-1620A(09) CL216-0400-0-09 SD-1620G(09) 33 | 27) 13] 21] 11 24 * CL216-0383-3-09 $D-1624A(09) CL216-0401-3-09 SD-1624G(09) 37 | 31) 13] 25 | 11 CL216-0385~9 28 #* CL216-0384-6-09 SD-1628A(09) CL216-0402-6-09 SD-1628G(09) 40 | 34 | 13 | 28 | 11. SD-1634A 34 %* CL216-0385-9-09 SD-1634A(09) CL216-0403~-9-09 SD~1634G(09) 45 | 39 | 13] 33) 11 ( 46 * CL216-0386-1-09 SD-1645A(09) CL216-0404-1-09 SD-1645BG(09) | 54] 48 | 13 | 42] 11 60 * CL216-0387~4-09 SD~1660A(09) CL216-0405-4-09 SD-1660BG(09) | 67 | 61 | 13 | 56 | 11 *: Standard NN yy 128Dip Spacer HRS No. Part No. Application Connector unit packing * CL216-0419-9 D-1600-SPA (applicable for models with any number of contacts) *CL216-0420-8 D-1600-SPB For packing with Connector unit stopper (applicable for models with any number of contacts) * Standard Mounting screws must be supplied by the customer Pin connectors Pin connectors Socket Connector Socket Connector | ~ without Brackets without Brackerts 47 1 pe ane eee cal Tana on Leper ty =| _D-1600-SPA iit =} p-1600-sPa Fay et rT tke : i \ : mY . P.C.B : m P.C.B Nut M2.6X0.45 4 | Nut (M2.6X0.45) [19 Screw M2.6X0.45X12 18 Screw (M2.6X0.45X12) D -1600SPA Male connector with side-lock type stopper bracket Female connector with side-lock type stopper bracket Male connector Female connector = with ST with ST le CUS 1.7 Oo | 27 b-1600-SPB O} D-1600-SPB Ouik = atte 10 } ms } Ls 3 = UC \ PCB {| PCB Nut (M2.6X0.45) \\ Nut (M2.60.45) Screw (M2.6X0.45X 12) ? < Screw (M2.6X0.45X 12) Lo ! * 2.7 Male connector with top-touch-lock type stopper | Female connector with top-touch-lock type stopper [ I a bracket bracket Female connector Male connector ee with ST __ with ST D~1600-SPB ( To) yu aN 134 b-4600-sPB ey 12.6 D-1600-SPB 1 - - too . 1 1th ob Te Be a CY) \ PCB 7 XK PCB 18 Nut (M2.6X0.45) 18 Nut (M2.6X0.45) Ed Screw (M2.6X0.45 X 12) * Screw (M2.6X0.45 X 12) Note 1: The connector unit packaging spacer (SPA) cannot be used for packing with the connector unit stopper bracket. The packaging spacer with connector unit stopper bracket (SPB) cannot be used for packaging the connector unit. Note 2: Provide two spacers (SPA and SPB) for each connector unit. * The dimensions marked with an asterisk (*) are for PCBs of 1.6mm in thickness. How to use connectors (1) When disconnecting, pull it as straight as possible, because the male pins might be damaged if it is twisted. (2) Connectors are available with gold to. be used in adverse environmental conditions and silver- plated pins be used in ordinary conditions. 129Recommended Dip Soldering Pattern of Connector rr When dip soldering the connectors to a PCB, drill holes as shown below. The figures indicate the num- ber of contacts. Signs 4 indicate the V-shaped mark (direction of the Recommended Dip Soldering Pattern of Pin Connector (View of the connector-mounting surface of substrate) (om) \ connector unit) on the mating face of the connector unit. PD1608 PD-1612 PD-1620 14.25 1] | 7 | 10.50 PD-1634 \ 130 PD-1624 29 ,Q__ . 24 .0m [r9.25e7=9.25] }-19.0+| 6.75 6.75 1.0 6.757 5.75 16-1.0 4.25 jet. 25 S108 4.25 3.25 08 4.25 3.25 : 1.75 0.75 1.75 1.75 f 0.75 1.75 1-75 0,75 1.75 a ST T ary v om A ot p<} et 4 Coby ON = T i Ta 1.75 at TTT 1.75 a a a 1.75 vo \ 22.96 2-2.99 22.94 ( PD-1616 PD1628 5.00 PD-1645PD1660 [-24.0->| [19.0 >| 81.0 6.75 6.75 ; 4. 225 : 4.25 3.25 1271.06 2.00 1.75 ' 0.75 2.00 ot T =O a tty yp ly ON ait rp rts 2.00 2-2.9 SD1608 SD-1612 SD-1616 10. SD-1620 SD-1624 SD-1628 N S 13114,25 | 75 | 3 75 34-1.0 60 3.00 50 on SD1634 SD-1645 2.50 - 00 7.50 10. 12.50 15.00 SD1660 mm . No. Appli- Recommended Mounting Hole of | A B c cable Pin Screw fgg A 8 19 13.5 8.5 B 12 24 18.5 8.5 f 16 29 23.5 8.5 @ 20 27 21.5 11,5 i 24 31 25.5 11.5 M2.6 ( 2-34 28 34 28.5 11.5 ~ 34 39 33.5 11.5 45 48 42.5 11.5 \ 60 61 55.5 11.5 SS) 132Function Chart 1 r Top-Touch Lock Side-Touch Lock Shoulder-Touch Lock CA Shell Plain Lock Polarizing Key * STA Stopper Bracket cg 4 Crimp Pin Contact Crimp Socket Contact Pes | pe 9 I | Li | TL Crimping Male Housing Female Housing STB Stopper Bracket ) Handle > J __S)) Soldering Eyelet Pin Insert Socket Insert | | Wire Wrapping Pin Insert Socket Insert f Straight Dip Soldering Socket Insert > | | Pin Insert * Dust cap is available for STA Stopper Bracket. 133SUMICON 1600 SERIES RIGHT-ANGLE DIP SOLDERING CONNECTORS (MALE) General The SUMICON 1600 series are Hirose right-angle dip soldering connectors (male). All models are compatible with the existing soldering type, wrapping type, crimping type, and straight dip soldering type connectors including their accessories. 20, 28, 34 and 60-contact models are available. fo? py f Ge? : fof Gf i Gd | fofod / / / | / j | | iLL | Features Direct dip soldering on a PCB~ enables conve- nient parallel connection with cable plugs. Suitable as an interface, being lightweight and capable of high-density packaging. Further cuts interconnection costs by using crimp- ing type plugs with plastic locks for simple cable connection, so no cases are needed. 4. A wide variety of connection methods available, e.g., dip soldering, wrapping, and crimping, to meet your requirements. Available with or without a top-touch lock type bracket and side-lock type bracket, offering you many choices for your applications. Highly solvent-resistant, using insulating materials with high heat resistance and chemical-resistance. Main Applications Electronic equipment such as computers, peripherals and terminals, control equipment, and measuring instru- ments. Electrical and Environmental Material and Finish \ Glass-Filled diallylphtalate resin Blue Type A: Silver-plated Brass Type 8: Gold~plated Polybutylenephthalate resin Blue(UL94V-0) Treated with chromate Steel over zinc plating ( Electrical Characteristics Current 3A Insulation Rating Contact Voltage AC 300V Rating Right Angle Contact 10m orless at DO1A Resistance Stopper Bracket Insulation 1000M Q or higher Resistance at DC 500V Withstand 1,000 Vr.m.s. for 1 minute \ Voltage 135Ordering Information ( Ul T \ Provided with a sequence of upper-case alphabe- tic characters. P R- 16 34 (1) (2) (3) (4): 5 ) ( 6 ) (7) (8 ) (1} Shape of terminal opening (6) Plating P: Male terminal A: Silver-plated (2) Terminal connection method G: Gold-plated R: Right-angle dip soldering (7) Accessories (3) Series No. ST: Side-lock type stopper bracket 16: 1600 series STA: Top-touch type stopper bracket (4) Number of contacts (8) R: Indicates a connector on which the STA bracket -(5) Serial sign for connector units is mounted in the reverse direction against the standard. (the standard refers to the direction in which both 4 marks on the STA bracket and con- nector unit are in the same direction). S Right Angle Dip Soldering Pin Connectors _ With Stopper Bracker for Top-Touch Lock Plug Shell XN 136 Unit: mm 4.3 3.5 A 2-6 2.9 ) Dip post0.5x0.5 wl [Fe & ~ ae tor T7 of N con 6 al Ol =) || a il V ~ B uw s c TSC ] a . CL. A Type No.of yp Alplc Pin HRS No. Part No. 20 CL216-0448-7 * PR-1620BA-STA 27 | 33 | 36 28 CL216-0450-9 * PR-1628BA~STA 34 | 40 | 43 34 CL216-0451~-1 * PR-1634BA-STA 39 | 45 | 48 CL216-0451-1 60 CL216-0453-7 * PR-1660BA-STA 61 | 67 | 70 PRAGSABA-STA *: Standard Gold plated type are available options. (With Stopper Bracket for Side-Touch Lock Plug Shell Unit: mm 14.3 3.5 (2,75 Dip Post 0.5x0.5 Type A N oor AlBic in HRS No. Part No. 20 CL216-0455-2 + PR-1620BA-ST 27 | 35 | 36 28 CL216-0457-8 * PR-1628BA-ST 34 | 42 | 43 34 CL216-0458-0 * PR-1634BA-ST 839 | 47 | 48 CL216-0458-0 PR-1634BA-ST 60 CL216-0460-2 * PR-1660BA-ST 61 | 69 | 70 \ *: Standard Gold plated type are available options / Connector Unit Only Without Bracket Unit: mm \ 2-$2.9 A ; | mle l ape tt ft Ss sl & & 1 iO L, | I= S | c he Yo Type A No.of AlBlc Pin HRS No. Part No. 20 | cL216-0461-5 * PR-1620BA 27 | 33 | 36 2g | cL216-0463-0 * PR-1628BA 34 | 40 | 43 CL216-0464-3 34 | CL216-0464-3 *PR-1634BA 39 | 45 | 48 PR-1634BA 60 | GL216-0466-9 * PR-1660BA 61 | 67 | 70 \ *: Standard Gold plated type are available options / 137With Stopper Bracket for Top Touch Lock Plug Shell in Reverse Position CL216-0498-5 PR-1634BA-STAR How to Use (Example) 14.3 3.5 {1.35} Unit: mm ) A 2-9 2.9 Post 0.5x0.5 | i we | +- & x a} | [@ oye| 4 a ln im ~ BS oa v LW J - A _ B | 15.7 so} | c El (oa wy wd A Type A No.of AlB/c HRS No. Part No. 20 | *CL216-0495-7-09 | PR-1620BA-STAR(09) | 27 | 33 | 36 28 | *CL216-0497-2-09 | PR-1628BA-STAR(09) | 34 | 40 | 43 34 | *CL216-0498-5-09 | PR~1634BA-STAR(09) | 39 | 45 | 48 60 | *CL216-0500-5-09 | PR-1660BA-STAR (09) | 61 | 67 | 70 *: Standard Gold plated types are available options. Note: When this type is used the mounting direction of socket insert In plug shell shall be in reverse position against the triangle mark on plug shell, cr Connector Mounting Side PCB 138 PR-16 ,BCI-STA With Top Touch Lock Bracket Top Touch Lock Plug Shell ; ~How to Use Right Angle Dip Soldering Connectors (, . The standard use of this type is to mount it on the left side of a vertical PC board. (Fig. 1) No. of pin PCB Fig. 1 NY 13 Right Angle | Connector ' _ c : Left side of PCB ~~ Pin No. nnector , . Mounting Side Dip Soldering Side / (, It is possible to mount it on the right side of PCB but special caution is necessary to be opposite all pin loca- tions on dip soldering surface. (Fig. 2) Pin No. Right Angle Connector Right side of PCB Dip soldering Side \ Fig. 2 Connector Mounting Side 1394 \ 3. When Top Touch Lock Type Plug Shell and Stop- Exit are upside down. per Bracket are used with mounts on the right side So, the Reverse Mount Stopper Bracket is con- of a PCB, not only the pin locations become oppo- veniet in such case.(Fig.3) site, but also the Lock Release Button and Cable Connector Mounting Side Lock Release Button A Mark 4 Mark fi Right side of PCB om | P] O08 2 | 4 | trys, 3 PE (: : 5 | Cable Exit cane ui / Top Tou | Touch Lock Top Tove | Shell | Dei u PCB Connector with Reverse Mount Stopper Bracket Socket Insert- Fig. 3 Plug Connector e Right Angle Connector with Reverse Mount Stopper Bracket 4. M2.6 screws are recommended to mount Right Angle Dip Soldering Pin Connectors. Please choose PC board thinner than 2.4mm. 6. In extracting plug connector, please pull it up straight out to prevent male pin from bending. 7. The standard plating is silver but gold is also an f available option. (" 8. Note: The dip soldering pattern on PCB of Right Angle Type and Straight Type are different from each other. 9. Before using a solvent other than trichloroethylene, chlorosene, methanol, isopropanol, or ethyalchol to wash soldered connectors, contact our engineer- ing department. a 140Recommended Dip Soldering Pattern ( NM 20- 1 2-M2.6 hole 0.5 2 dl YY A 19 47l + + i ~ os o _ ww a Mma rp (ot a PCB End 6.755. ot 43s PR-1620B 19.5 14.25 14.25 11.75 | 11.75 8.25 | 9.25 5.75|6.75 tir 2-M2.6 hole 0.75 | 1.75 oN Pin No. I a WV + + + + + + + + + 21-4224 pg ____________ 1+ PCB End 7 |5.5 9.5 | 8 13 10.5 PR-1634B same mark on the connector unit. Note 1. The triangle mark represents the position of the nm 34 a 11.75 | 11.75 9.25 | 9.25 5.75) 6.75 25)4.25 28- 1 t 2-M2.6 hole 0.75)1.75, oF A 4 I + + > VY OT48T 4 97 3 Pin No. PCB End Vin avy ays 10.5 | 8 PR-1628B 61 2-M2.6 hole 1.25 | 3. 25 3.75 PIn No. PCB End 6.25] 6.25 8.75 | 8.75 1.25 | 11.25 13.75 13.75 16.25 16.25 18.75 18.75 23.75 21.25 PR-1660B 2. Above pattern is shown from view direction of the connector mounting side. ) 141Recommended Mounting Pattern cr * Post hole I . | 7 mr NN an om Pin No. PCB End _ Connector With top-touch-lock type stopper bracket re 7.5 max 2-M2.6 hole 4 1 7.9 max. >} 10.4 max. { | 1 . o / Te PCB End Connector With side-lock type stopper bracket A 2-M2.6 hole Post hole | ; x [Set | ! E ! 7 ee g r ! | =) | KI] FI | ts -- -- NAT ot \_Pin No. No. tt _ __ PCB End Connector Connector Unit Type The triangle mark represents the position of the same mark on the connector unit. Above pattern is shown from view direction of the con- nector mounting side. 142 For insertion-soldering in the PCB, drill mounting holes as shown in the figure below. N eon A 20 27 28 34 34 39 60 61 ooFunction Chart 2 7 Top-Touch Lock | | | | 0 *Right-Angle Dip STA stopper bracket Side-Touch Lock Right-Angle Dip ST stopper bracket Right-Angle Dip Connector Unit *Dust cap is available for STA stopper bracket. Crimp Socket Contact Plain Lock (only for the combination ieee with Right Angle Dip Connector Unit) Socket Insert + f Socket Insert Socket Insert Crimping Female Housing Soldering Eyelet Wire Wrapping > | Straight-Dip Soldering ~ 143