LM78LXX Series 3-Terminal Positive Regulators General Description The LM78LXX series of three terminal positive regulators is available with several fixed output voltages making them useful in a wide range of applications. When used as a zener diode/resistor combination replacement, the LM78LXX usually results in an effective output impedance improvement of two orders of magnitude, and lower quiescent current. These regulators can provide local on card regulation, eliminating the distribution problems associated with single point regulation. The voltages available allow the LM78LXX to be used in logic systems, instrumentation, HiFi, and other solid state electronic equipment. The LM78LXX is available in the plastic TO-92 (Z) package, the plastic SO-8 (M) package and a chip sized package (8Bump micro SMD) using National's micro SMD package technology. With adequate heat sinking the regulator can deliver 100mA output current. Current limiting is included to limit the peak output current to a safe value. Safe area protection for the output transistors is provided to limit internal power dissi- pation. If internal power dissipation becomes too high for the heat sinking provided, the thermal shutdown circuit takes over preventing the IC from overheating. Features LM78L05 in micro SMD package Output voltage tolerances of 5% over the temperature range Output current of 100mA Internal thermal overload protection Output transistor safe area protection Internal short circuit current limit Available in plastic TO-92 and plastic SO-8 low profile packages No external components Output voltages of 5.0V, 6.2V, 8.2V, 9.0V, 12V, 15V See AN-1112 for micro SMD considerations Connection Diagrams SO-8 Plastic (M) (Narrow Body) 8-Bump micro SMD 774402 Top View 774424 Top View (Bump Side Down) (TO-92) Plastic Package (Z) micro SMD Marking Orientation 774403 Bottom View 774433 Top View (c) 2012 Texas Instruments Incorporated 7744 SNVS754H www.ti.com LM78LXX Series 3-Terminal Positive Regulators January 15, 2012 LM78LXX Series Ordering Information Package Type NSC Drawing Output Voltage Operating Temperature Range micro SMD BPA08AAB 5.0V -40C to 85C 5.0V -40C to 85C 9.0V -40C to 85C Thin micro SMD TPA08AAA 0C to 125C 5.0V -40C to 125C SOIC Narrow TO-92 www.ti.com M08A Z03A 12V 0C to 125C 15V 0C to 125C 5.0V Order Number Supplied As LM78L05IBP OBSOLETE LM78L05IBPX OBSOLETE LM78L05ITP Reel of 250 LM78L05ITPX Reel of 3000 LM78L09ITP OBSOLETE LM78L09ITPX Reel of 3000 LM78L05ACM Rail of 95 LM78L05ACMX Reel of 2500 LM78L05AIM Rail of 95 LM78L05AIMX Reel of 2500 LM78L12ACM Rail of 95 LM78L12ACMX Reel of 2500 LM78L15ACM Rail of 95 LM78L15ACMX Reel of 2500 0C to 125C LM78L05ACZ Box of 1800 6.2V 0C to 125C LM78L62ACZ Box of 1800 8.2V 0C to 125C LM78L82ACZ OBSOLETE 9.0V 0C to 125C LM78L09ACZ OBSOLETE 12V 0C to 125C LM78L12ACZ Box of 1800 15V 0C to 125C LM78L15ACZ Box of 1800 2 If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. Power Dissipation (Note 5) Input Voltage Storage Temperature ESD Susceptibility (Note 2) Internally Limited 35V -65C to +150C 1kV 0C to 125C 0C to 125C -40C to 125C -40C to 85C -40C to 85C 235C 260C (lead time) LM78LXX Electrical Characteristics Limits in standard typeface are for TJ = 25C, Bold typeface applies over the entire operating temperature range of the indicated package. Limits are guaranteed by production testing or correlation techniques using standard Statistical Quality Control (SQC) methods. Unless otherwise specified: IO = 40mA, CI = 0.33F, CO = 0.1F. LM78L05AC / LM78L05I Unless otherwise specified, VIN = 10V Symbol VO Parameter Conditions Output Voltage Min Typ Max 4.8 5 5.2 Units 7V VIN 20V 1mA IO 40mA (Note 3) 1mA IO 70mA (Note 3) VO Line Regulation VO Load Regulation IQ Quiescent Current IQ Quiescent Current Change Vn 8V VIN 20V 10 54 1mA IO 100mA 20 60 1mA IO 40mA 5 30 3 1.0 1mA IO 40mA 0.1 f = 120 Hz Peak Output Current JA Thermal Resistance (8-Bump micro SMD) IO = 5mA 47 mV mA 40 V 62 dB 140 mA -0.65 mV/C 6.7 230.9 3 V 5 8V VIN 20V Ripple Rejection Minimum Value of Input Voltage Required to Maintain Line Regulation 5.25 75 f = 10 Hz to 100 kHz (Note 4) VIN (Min) 4.75 18 Output Noise Voltage Average Output Voltage Tempco 5.25 7V VIN 20V 8V VIN 16V IPK 4.75 7 V C/W www.ti.com LM78LXX Series Operating Junction Temperature LM78LxxACZ, TO-92 LM78LxxACM, SO-8 LM78LxxAIM, SO-8 LM78LxxIBPX, micro SMD LM78LxxITP, Thin micro SMD Soldering Information Infrared or Convection (20 sec.) Wave Soldering (10 sec.) Absolute Maximum Ratings (Note 1) LM78LXX Series LM78L62AC Unless otherwise specified, VIN = 12V Symbol VO Parameter Conditions Output Voltage Min Typ Max 5.95 6.2 6.45 Units 8.5V VIN 20V 1mA IO 40mA (Note 3) 1mA IO 70mA (Note 3) VO Line Regulation VO Load Regulation IQ Quiescent Current IQ Quiescent Current Change Vn 6.5 5.9 6.5 8.5V VIN 20V 65 175 9V VIN 20V 55 125 1mA IO 100mA 13 80 1mA IO 40mA 6 40 2 5.5 8V VIN 20V 1.5 1mA IO 40mA 0.1 Output Noise Voltage f = 10 Hz to 100 kHz (Note 4) Ripple Rejection f = 120 Hz 10V VIN 20V IPK 5.9 40 Peak Output Current Average Output Voltage Tempco VIN (Min) IO = 5mA Minimum Value of Input Voltage Required to Maintain Line Regulation V mV mA 50 V 46 dB 140 mA -0.75 mV/C 7.9 V LM78L82AC Unless otherwise specified, VIN = 14V Symbol VO Parameter Conditions Output Voltage Min Typ Max 7.87 8.2 8.53 Units 11V VIN 23V 1mA IO 40mA (Note 3) 1mA IO 70mA (Note 3) VO VO Line Regulation Load Regulation IQ Quiescent Current IQ Quiescent Current Change Vn www.ti.com 8.6 175 12V VIN 23V 70 125 1mA IO 100mA 15 80 1mA IO 40mA 8 40 2 5.5 12V VIN 23V 1.5 1mA IO 40mA 0.1 f = 10 Hz to 100 kHz (Note 4) Ripple Rejection f = 120 Hz 4 7.8 80 Output Noise Voltage Peak Output Current 8.6 11V VIN 23V 12V VIN 22V IPK 7.8 39 V mV mA 60 V 45 dB 140 mA Parameter Conditions Average Output Voltage Tempco VIN (Min) Min IO = 5mA Minimum Value of Input Voltage Required to Maintain Line Regulation Typ Max Units -0.8 mV/C 9.9 V LM78L09AC / LM78L09I Unless otherwise specified, VIN = 15V Symbol VO Parameter Conditions Output Voltage Min Typ Max 8.64 9.0 9.36 Units 11.5V VIN 24V 1mA IO 40mA (Note 3) 1mA IO 70mA (Note 3) VO Line Regulation VO Load Regulation IQ Quiescent Current IQ Quiescent Current Change Vn Output Noise Voltage 8.55 9.45 8.55 9.45 11.5V VIN 24V 100 200 13V VIN 24V 90 150 1mA IO 100mA 20 90 1mA IO 40mA 10 45 2 5.5 11.5V VIN 24V 1.5 1mA IO 40mA Ripple Rejection f = 120 Hz 15V VIN 25V IPK VIN (Min) mV mA 0.1 38 Peak Output Current Average Output Voltage Tempco V IO = 5mA Minimum Value of Input Voltage Required to Maintain Line Regulation 70 V 44 dB 140 mA -0.9 mV/C 10.7 V LM78L12AC Unless otherwise specified, VIN = 19V Symbol VO Parameter Conditions Output Voltage Min Typ Max 11.5 12 12.5 Units 14.5V VIN 27V 1mA IO 40mA (Note 3) 1mA IO 70mA (Note 3) VO VO Line Regulation Load Regulation IQ Quiescent Current IQ Quiescent Current Change Vn Output Noise Voltage 11.4 12.6 11.4 12.6 14.5V VIN 27V 30 180 16V VIN 27V 20 110 1mA IO 100mA 30 100 1mA IO 40mA 10 50 3 5 16V VIN 27V 1 1mA IO 40mA 0.1 80 5 V mV mA V www.ti.com LM78LXX Series Symbol LM78LXX Series Symbol Parameter Conditions Ripple Rejection f = 120 Hz 15V VIN 25 IPK Min Typ 40 54 dB 140 mA -1.0 mV/C Peak Output Current Average Output Voltage Tempco VIN (Min) IO = 5mA Minimum Value of Input Voltage Required to Maintain Line Regulation Max Units 13.7 14.5 V Min Typ Max Units 14.4 15.0 15.6 LM78L15AC Unless otherwise specified, VIN = 23V Symbol VO Parameter Conditions Output Voltage 17.5V VIN 30V 1mA IO 40mA (Note 3) 1mA IO 70mA (Note 3) VO Line Regulation VO Load Regulation IQ 14.25 15.75 14.25 15.75 17.5V VIN 30V 37 250 20V VIN 30V 25 140 1mA IO 100mA 35 150 1mA IO 40mA 12 75 3 5 Quiescent Current IQ Vn Quiescent Current Change 20V VIN 30V 1 1mA IO 40mA 0.1 Output Noise Voltage Ripple Rejection f = 120 Hz 18.5V VIN 28.5V IPK Peak Output Current Average Output Voltage Tempco VIN (Min) IO = 5mA Minimum Value of Input Voltage Required to Maintain Line Regulation 37 V mV mA 90 V 51 dB 140 mA -1.3 mV/C 16.7 17.5 V Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Electrical specifications do not apply when operating the device outside of its stated operating conditions. Note 2: Human body model, 1.5 k in series with 100pF. Note 3: Power dissipation 0.75W. Note 4: Recommended minimum load capacitance of 0.01F to limit high frequency noise. Note 5: Typical thermal resistance values for the packages are: Z Package: JC = 60 C/W, = JA = 230 C/W M Package: JA = 180 C/W micro SMD Package: JA = 230.9C/W www.ti.com 6 LM78LXX Series Typical Performance Characteristics Maximum Average Power Dissipation (Z Package) Peak Output Current 774414 774416 Dropout Voltage Ripple Rejection 774417 774418 Output Impedance Quiescent Current 774420 774419 7 www.ti.com LM78LXX Series Quiescent Current 774421 Equivalent Circuit LM78LXX 774407 www.ti.com 8 LM78LXX Series Typical Applications Fixed Output Regulator 774408 *Required if the regulator is located more than 3 from the power supply filter. **See (Note 4) in the electrical characteristics table. Adjustable Output Regulator 774409 VOUT = 5V + (5V/R1 + IQ) R2 5V/R1 > 3 IQ, load regulation (Lr) [(R1 + R2)/R1] (Lr of LM78L05) Current Regulator 774410 IOUT = (VOUT/R1) + IQ >IQ = 1.5mA over line and load changes 5V, 500mA Regulator with Short Circuit Protection 774411 *Solid tantalum. **Heat sink Q1. ***Optional: Improves ripple rejection and transient response. Load Regulation: 0.6% 0 IL 250mA pulsed with tON = 50ms. 9 www.ti.com LM78LXX Series 15V, 100mA Dual Power Supply 774412 *Solid tantalum. Variable Output Regulator 0.5V-18V 774413 *Solid tantalum. VOUT = VG + 5V, R1 = (-VIN/IQ LM78L05) VOUT = 5V (R2/R4) for (R2 + R3) = (R4 + R5) A 0.5V output will correspond to (R2/R4) = 0.1 (R3/R4) = 0.9 www.ti.com 10 LM78LXX Series Physical Dimensions inches (millimeters) unless otherwise noted NOTES: UNLESS OTHERWISE SPECIFIED 1. EPOXY COATING 2. 63Sn/37Pb EUTECTIC BUMP 3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD. 4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION. REMAINING PINS ARE NUMBERED COUNTERCLOCKWISE. 5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT. 6. REFERENCE JEDEC REGISTRATION MO-211, VARIATION BC. 8-Bump micro SMD NS Package Number BPA08AAB X1 = 1.285mm X2 = 1.285mm X3 = 0.850mm 11 www.ti.com LM78LXX Series 8-Bump Thin micro SMD NS Package Number TPA08AAA X1 = 1.285mm X2 = 1.285mm X3 = 0.500mm S.O. Package (M) NS Package Number M08A www.ti.com 12 LM78LXX Series Molded Offset TO-92 (Z) NS Package Number Z03A 13 www.ti.com LM78LXX Series 3-Terminal Positive Regulators Notes www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated